Hi JJ, On 01/31/2018 12:01 AM, Jean-Jacques Hiblot wrote: > > This series adds the missing bits to enable the UHS and HS200 modes > for the TI platforms. > > Enabling support for high speed modes on omap5 requires implementing: > * io signal voltage selection > * tuning support > * pin configuration (IO delays) > > The few last patches enable the high speed modes for the DRA7 platforms and > also take care of disabling those modes in the dts for the platforms that > cannot support either the UHS or the HS200 because the voltage regulators > on board would not allow using those modes (not a SOC limitation). > > With this in place we observe significant improvements in the performances: > on a DRA72 evm: > eMMC HS200: 124 MB/s > eMMC DDR52: 78 MB/s > sd SDR104: 71 MB/s > sd SDR50: 44 MB/s > For the record, the original performances were: > SD High speed: 18 MB/s > MMC High speed: 18 MB/s > > This series has been tested on: > * DRA71-evm > * DRA72-evm > * DRA7x-evm > * DRA76-evm > * AM57x-evm > * Beaglebone Black (dt and non-dt) > > Changes in v2: > - rebased on top of u-boot/master > - enable the H200 and UHS support in the defconfigs of the DRA7 platforms > > Changes in v3: > - in omap_hsmmc_set_clock(), if mmc->clock is zero, use the max divider. > - prefer the usage of the BIT() macro over the construct ( 1 << x ) > - fixed build issue with omap3 platforms
Applied to u-boot-mmc. Sorry for late. Best Regards, Jaehoon Chung > > Jean-Jacques Hiblot (13): > mmc: omap_hsmmc: cleanup clock configuration > mmc: omap_hsmmc: set MMC mode in the UHSMS bit field > mmc: omap_hsmmc: Add tuning support > mmc: omap_hsmmc: Workaround for errata id i802 > mmc: omap_hsmmc: Reduce the max timeout for reset controller fsm > mmc: omap_hsmmc: allow the simple HS modes to use the default pinctrl > mmc: omap_hsmmc: update mmc->clock with the actual bus speed > mmc: omap_hsmmc: implement send_init_stream callback > mmc: omap_hsmmc: add signal voltage selection support > ARM: dts: dra7: Add supported MMC/SD modes in MMC dt nodes > dts: am57xx-beagle-x15: disable UHS and HS200 support > dts: am57xx-idk: disable HS200 support > configs: dra7xx_evm/dra7xx_hs_evm: Enable MMC HS200 and SD UHS support > > Kishon Vijay Abraham I (11): > mmc: omap_hsmmc: cleanup omap_hsmmc_set_ios > mmc: omap_hsmmc: add support to set default io voltage > mmc: omap_hsmmc: Enable DDR mode support > mmc: omap_hsmmc: use mmc_of_parse to populate mmc_config > ARM: OMAP5/DRA7: Enable iodelay recalibration to be done from uboot > mmc: omap_hsmmc: Add support to set IODELAY values > mmc: omap_hsmmc: Add support to get pinctrl values and max frequency > for different hw revisions > mmc: omap_hsmmc: allow mmc clock to be gated > ARM: OMAP5: set mmc clock frequency to 192MHz > ARM: dts: DRA7: use new dra7-specific compatible string > ARM: DRA7x/AM57x: Add MMC/SD fixups for rev1.0 and rev 1.1 > > arch/arm/dts/am57xx-beagle-x15.dts | 6 + > arch/arm/dts/am57xx-idk-common.dtsi | 2 + > arch/arm/dts/dra7.dtsi | 22 +- > arch/arm/include/asm/arch-omap5/clock.h | 2 +- > arch/arm/include/asm/arch-omap5/dra7xx_iodelay.h | 3 + > arch/arm/include/asm/arch-omap5/sys_proto.h | 7 + > arch/arm/include/asm/omap_mmc.h | 59 +- > arch/arm/mach-omap2/omap5/dra7xx_iodelay.c | 30 + > arch/arm/mach-omap2/omap5/hw_data.c | 10 +- > board/ti/am57xx/board.c | 30 + > board/ti/dra7xx/evm.c | 29 + > configs/dra7xx_evm_defconfig | 3 + > configs/dra7xx_hs_evm_defconfig | 3 + > drivers/mmc/omap_hsmmc.c | 952 > +++++++++++++++++++++-- > include/configs/am57xx_evm.h | 2 - > include/configs/dra7xx_evm.h | 2 - > 16 files changed, 1087 insertions(+), 75 deletions(-) > _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot