Executing a command is matter of always doing the following sequence: * Waiting for the FIFO to be empty so we can fill it with the new command. * Clearing the status register. * Writing the command in the FIFO. * Waiting for the command to finish.
Add a nand_exec_cmd() helper to handle this instead of repeating the logic through the various functions. Signed-off-by: Miquel Raynal <miquel.ray...@bootlin.com> Acked-by: Boris Brezillon <boris.brezil...@bootlin.com> --- drivers/mtd/nand/sunxi_nand_spl.c | 42 +++++++++++++++++++-------------------- 1 file changed, 21 insertions(+), 21 deletions(-) diff --git a/drivers/mtd/nand/sunxi_nand_spl.c b/drivers/mtd/nand/sunxi_nand_spl.c index 913de7d442..25a0941fd2 100644 --- a/drivers/mtd/nand/sunxi_nand_spl.c +++ b/drivers/mtd/nand/sunxi_nand_spl.c @@ -177,6 +177,20 @@ static int nand_wait_int(void) return 0; } +static int nand_exec_cmd(u32 cmd) +{ + int ret; + + ret = nand_wait_cmd_fifo_empty(); + if (ret) + return ret; + + writel(NFC_ST_CMD_INT_FLAG, SUNXI_NFC_BASE + NFC_ST); + writel(cmd, SUNXI_NFC_BASE + NFC_CMD); + + return nand_wait_int(); +} + void nand_init(void) { uint32_t val; @@ -194,13 +208,7 @@ void nand_init(void) } /* reset NAND */ - nand_wait_cmd_fifo_empty(); - - writel(NFC_ST_CMD_INT_FLAG, SUNXI_NFC_BASE + NFC_ST); - writel(NFC_SEND_CMD1 | NFC_WAIT_FLAG | NAND_CMD_RESET, - SUNXI_NFC_BASE + NFC_CMD); - - nand_wait_int(); + nand_exec_cmd(NFC_SEND_CMD1 | NFC_WAIT_FLAG | NAND_CMD_RESET); } static void nand_apply_config(const struct nfc_config *conf) @@ -221,37 +229,29 @@ static int nand_load_page(const struct nfc_config *conf, u32 offs) { int page = offs / conf->page_size; - nand_wait_cmd_fifo_empty(); - writel((NFC_CMD_RNDOUTSTART << NFC_RANDOM_READ_CMD1_OFFSET) | (NFC_CMD_RNDOUT << NFC_RANDOM_READ_CMD0_OFFSET) | (NFC_CMD_READSTART << NFC_READ_CMD_OFFSET), SUNXI_NFC_BASE + NFC_RCMD_SET); writel(((page & 0xFFFF) << 16), SUNXI_NFC_BASE + NFC_ADDR_LOW); writel((page >> 16) & 0xFF, SUNXI_NFC_BASE + NFC_ADDR_HIGH); - writel(NFC_ST_CMD_INT_FLAG, SUNXI_NFC_BASE + NFC_ST); - writel(NFC_SEND_CMD1 | NFC_SEND_CMD2 | NFC_RAW_CMD | NFC_WAIT_FLAG | - ((conf->addr_cycles - 1) << NFC_ADDR_NUM_OFFSET) | NFC_SEND_ADDR, - SUNXI_NFC_BASE + NFC_CMD); - return nand_wait_int(); + return nand_exec_cmd(NFC_SEND_CMD1 | NFC_SEND_CMD2 | NFC_RAW_CMD | + NFC_SEND_ADDR | NFC_WAIT_FLAG | + ((conf->addr_cycles - 1) << NFC_ADDR_NUM_OFFSET)); } static int nand_reset_column(void) { - nand_wait_cmd_fifo_empty(); - writel((NFC_CMD_RNDOUTSTART << NFC_RANDOM_READ_CMD1_OFFSET) | (NFC_CMD_RNDOUT << NFC_RANDOM_READ_CMD0_OFFSET) | (NFC_CMD_RNDOUTSTART << NFC_READ_CMD_OFFSET), SUNXI_NFC_BASE + NFC_RCMD_SET); - writel(NFC_ST_CMD_INT_FLAG, SUNXI_NFC_BASE + NFC_ST); writel(0, SUNXI_NFC_BASE + NFC_ADDR_LOW); - writel(NFC_SEND_CMD1 | NFC_SEND_CMD2 | NFC_RAW_CMD | - (1 << NFC_ADDR_NUM_OFFSET) | NFC_SEND_ADDR | NFC_CMD_RNDOUT, - SUNXI_NFC_BASE + NFC_CMD); - return nand_wait_int(); + return nand_exec_cmd(NFC_SEND_CMD1 | NFC_SEND_CMD2 | NFC_RAW_CMD | + (1 << NFC_ADDR_NUM_OFFSET) | NFC_SEND_ADDR | + NFC_CMD_RNDOUT); } static int nand_read_page(const struct nfc_config *conf, u32 offs, -- 2.14.1 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot