Hello All,
Im booting Linux on arm64 using FIT multi image (image + initrd + DTB). So
if I increase the initrd size (from 16 MB -> 20MB) board hangs at "starting
kernel"). However if I change the load address of bootm (from 0x2000000 to
0x1000000) it boots successfully. Any pointers on why this is booting at
lower load address? thanks in advance.
Board config : 2 GB ram (0x00000000 - 0x8000000)
Init high enabled (so initrd is relocated to high mem)
FDT_high=0xffffffffffffffff so DTB is used in place.
FDT load adress is (0x9000000)
Following is the console o/p:
## Current stack ends at 0x7f6cc6c0 * kernel: cmdline image address =
0x02000000
## Loading kernel from FIT Image at 02000000 ...
Using 'config@1' configuration
Verifying Hash Integrity ... OK
Trying 'kernel@0' kernel subimage
Description: linux-mvl-4.4
Type: Kernel Image
Compression: uncompressed
Data Start: 0x020000bc
Data Size: 12473856 Bytes = 11.9 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00080000
Entry Point: 0x00080000
Verifying Hash Integrity ... OK
kernel data at 0x020000bc, len = 0x00be5600 (12473856)
* ramdisk: using config 'config@1' from image at 0x02000000
## Loading ramdisk from FIT Image at 02000000 ...
Using 'config@1' configuration
Trying 'ramdisk@0' ramdisk subimage
Description: initramfs
Type: RAMDisk Image
Compression: lzma compressed
Data Start: 0x02be5764
Data Size: 22356891 Bytes = 21.3 MiB
Architecture: AArch64
OS: Linux
Can't get 'load' property from FIT 0x02000000, node: offset 12474104, name
ramdisk@0 (FDT_ERR_NOTFOUND)
Load Address: unavailable
Can't get 'entry' property from FIT 0x02000000, node: offset 12474104, name
ramdisk@0 (FDT_ERR_NOTFOUND)
Entry Point: unavailable
Verifying Hash Integrity ... OK
Can't get 'load' property from FIT 0x02000000, node: offset 12474104, name
ramdisk@0 (FDT_ERR_NOTFOUND)
ramdisk start = 0x02be5764, ramdisk end = 0x04137aff
* fdt: using config 'config@1' from image at 0x02000000
## Checking for 'FDT'/'FDT Image' at 02000000
## Loading fdt from FIT Image at 02000000 ...
Using 'config@1' configuration
Trying 'fdt@1' fdt subimage
Description: P1 fdt
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x0413eadc
Data Size: 28899 Bytes = 28.2 KiB
Architecture: AArch64
Verifying Hash Integrity ... OK
Loading fdt from 0x0413eadc to 0x09000000
Booting using the fdt blob at 0x9000000
of_flat_tree at 0x09000000 size 0x000070e3
Loading Kernel Image ... OK
kernel loaded at 0x00080000, end = 0x00c65600
## initrd_high = 0x80000000, copy_to_ram = 1
Loading Ramdisk to 7e179000, end 7f6cb39b ... OK
ramdisk load start = 0x7e179000, ramdisk load end = 0x7f6cb39b
using: FDT
## DT length 41187
Using Device Tree in place at 0000000009000000, end 000000000900a0e2
mci_find_sb_node.....no Device found
DevID=100001f found on MCi bus 0
DevID=1000021 found on MCi bus 1
## Transferring control to Linux (at address 80000)...
######## Starting kernel ...
--
Sent from: http://u-boot.10912.n7.nabble.com/
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
