hi alessandro,
El Fri, Feb 12, 2010 at 10:23:58AM +0100 Matthias Kaehlcke ha dit:
> El Fri, Feb 12, 2010 at 08:01:26AM +0100 Alessandro Rubini ha dit:
>
> > > i gave my ack after a visual review of the patch, without having
> > > tested it. i just installed a patched u-boot on one of my boards and
> > > it doesn't boot :(
> >
> > Oh. The opposite of my board.
> >
> > Then, since I don't have a 9315A but only a similar one, it's better
> > to drop the patch. I'll have a different sdram_cfg file for mine,
> > then.
>
> i'm pretty sure we'll be able to track this down, the purpose of your
> patch is correct, i actually wonder why the current code works ...
>
> if we can't solve the issue in the next days, you could still send a
> patch which only writes the GlConfig register in
> program_mode_registers(). this would fix at least on of the issues and
> make your code less different from the one in the tree
maybe i have found a clue: i think the original assembly code wasn't
correct either. the comment talks about reading from each bank, but
then code like this is excuted:
ldr r0, =0x00000000 /* A[22:21] = b00 */
str r0, [r0]
which *writes* to the bank, but doesn't read from it.
according to the errata note a bank is precharged by reading from
it. the current code does this, but before the bank is configured
properly. i suspect that is the cause for the hang i see on my
boards. i've put together some code which does the precharge after
setting up the mode registers. on my boards based on the edb9301 and
edb9307a design u-boot boots with this code.
below you find a patch, could you give it a try on your board, when
you find some time and feel well enough?
thanks
Matthias
---
diff --git a/board/edb93xx/sdram_cfg.c b/board/edb93xx/sdram_cfg.c
index 6155f0e..f3db750 100644
--- a/board/edb93xx/sdram_cfg.c
+++ b/board/edb93xx/sdram_cfg.c
@@ -47,25 +47,27 @@ void sdram_cfg(void)
early_udelay(200);
- force_precharge();
+ /*
+ * Errata of most EP93xx revisions say that PRECHARGE ALL isn't always
+ * issued, so we omit it at this point. Instead we force a precharge
+ * after having programmed the mode registers
+ */
setup_refresh_timer();
program_mode_registers();
- /* Select normal operation mode */
- writel(GLCONFIG_CKE, &sdram->glconfig);
+ force_precharge();
}
static void force_precharge(void)
{
- /*
- * Errata most EP93xx revisions say that PRECHARGE ALL isn't always
- * issued.
- *
- * Do a read from each bank to make sure they're precharged
- */
+ struct sdram_regs *sdram = (struct sdram_regs *)SDRAM_BASE;
+
+ /* Select normal operation mode */
+ writel(GLCONFIG_CKE, &sdram->glconfig);
+ /* Do a read from each bank to make sure they're precharged */
PRECHARGE_BANK(0);
PRECHARGE_BANK(1);
PRECHARGE_BANK(2);
@@ -101,6 +103,11 @@ static void setup_refresh_timer(void)
static void program_mode_registers(void)
{
+ struct sdram_regs *sdram = (struct sdram_regs *)SDRAM_BASE;
+
+ /* Select mode register update mode */
+ writel(GLCONFIG_MRS | GLCONFIG_CKE, &sdram->glconfig);
+
/*
* The mode registers are programmed by performing a read from each
* SDRAM bank. The value of the address that is read defines the value
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
