Some hardware designs connect a CPU MAC directly to the RGMII interface
of a mv88e61xx device. On such devices a delay on the RX/TX lines is
required, this can either be achieved by adding extra length to the
traces on the PCB or by implementing the delay in silicon. This is
an implementation of the latter.
Signed-off-by: Chris Packham <judge.pack...@gmail.com>
---
drivers/net/phy/Kconfig | 4 ++++
drivers/net/phy/mv88e61xx.c | 26 ++++++++++++++++++++++++++
2 files changed, 30 insertions(+)
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index f5821dfed96d..98cd57eea977 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -59,6 +59,10 @@ config MV88E61XX_PHY_PORTS
config MV88E61XX_FIXED_PORTS
hex "Bitmask of PHYless serdes Ports"
+config MV88E61XX_RGMII_DELAY
+ bool "Add delay to RGMII outputs"
+ default n
+
endif # MV88E61XX_SWITCH
config PHYLIB_10G
diff --git a/drivers/net/phy/mv88e61xx.c b/drivers/net/phy/mv88e61xx.c
index ea54a1531053..d258ba1ef0f3 100644
--- a/drivers/net/phy/mv88e61xx.c
+++ b/drivers/net/phy/mv88e61xx.c
@@ -69,6 +69,7 @@
#define PORT_REG_CTRL 0x04
#define PORT_REG_VLAN_MAP 0x06
#define PORT_REG_VLAN_ID 0x07
+#define PORT_REG_RGMII_TIMING 0x1A
/* Phy registers */
#define PHY_REG_CTRL1 0x10
@@ -122,6 +123,9 @@
#define PORT_REG_VLAN_MAP_TABLE_SHIFT 0
#define PORT_REG_VLAN_MAP_TABLE_WIDTH 11
+#define PORT_REG_RGMII_TIMING_RX_DELAY BIT(10)
+#define PORT_REG_RGMII_TIMING_TX_DELAY BIT(9)
+
#define SERDES_REG_CTRL_1_FORCE_LINK BIT(10)
#define PHY_REG_CTRL1_ENERGY_DET_SHIFT 8
@@ -705,6 +709,24 @@ unforce:
return res;
}
+static int mv88e61xx_rgmii_timing_cfg(struct phy_device *phydev)
+{
+#ifdef CONFIG_MV88E61XX_RGMII_DELAY
+ int val;
+
+ val = mv88e61xx_port_read(phydev, 6, PORT_REG_RGMII_TIMING);
+ if (val < 0)
+ return val;
+
+ val |= PORT_REG_RGMII_TIMING_RX_DELAY |
+ PORT_REG_RGMII_TIMING_TX_DELAY;
+
+ return mv88e61xx_port_write(phydev, 6, PORT_REG_RGMII_TIMING, val);
+#else
+ return 0;
+#endif
+}
+
static int mv88e61xx_fixed_port_setup(struct phy_device *phydev, u8 port)
{
int val;
@@ -774,6 +796,10 @@ static int mv88e61xx_set_cpu_port(struct phy_device
*phydev)
return val;
}
} else {
+ val = mv88e61xx_rgmii_timing_cfg(phydev);
+ if (val < 0)
+ return val;
+
val = mv88e61xx_fixed_port_setup(phydev,
CONFIG_MV88E61XX_CPU_PORT);
if (val < 0)
--
2.18.0
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
