Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint OCM memory. This configuration
only has required parallel nor flash support.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.palad...@xilinx.com>
---
Changes from v3:
- None, rebased on latest master
Changes from v2:
- None
Changes from v1:
- None
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/zynq-cse-nor.dts | 88 ++++++++++++++++++++++++++++++++++++++++++
configs/zynq_cse_nor_defconfig | 50 ++++++++++++++++++++++++
3 files changed, 139 insertions(+)
create mode 100644 arch/arm/dts/zynq-cse-nor.dts
create mode 100644 configs/zynq_cse_nor_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 834a19b..6785fef 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -130,6 +130,7 @@ dtb-$(CONFIG_ARCH_UNIPHIER_SLD8) += \
dtb-$(CONFIG_ARCH_ZYNQ) += \
zynq-cc108.dtb \
zynq-cse-nand.dtb \
+ zynq-cse-nor.dtb \
zynq-cse-qspi-single.dtb \
zynq-microzed.dtb \
zynq-minized.dtb \
diff --git a/arch/arm/dts/zynq-cse-nor.dts b/arch/arm/dts/zynq-cse-nor.dts
new file mode 100644
index 0000000..ba6f9a1
--- /dev/null
+++ b/arch/arm/dts/zynq-cse-nor.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Xilinx CSE NOR board DTS
+ *
+ * Copyright (C) 2018 Xilinx, Inc.
+ */
+/dts-v1/;
+#include "zynq-7000.dtsi"
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "Zynq CSE NOR Board";
+ compatible = "xlnx,zynq-cse-nor", "xlnx,zynq-7000";
+
+ aliases {
+ serial0 = &dcc;
+ };
+
+ memory@fffc0000 {
+ device_type = "memory";
+ reg = <0xFFFC0000 0x40000>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ dcc: dcc {
+ compatible = "arm,dcc";
+ status = "disabled";
+ u-boot,dm-pre-reloc;
+ };
+
+ amba: amba {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&intc>;
+ ranges;
+
+ intc: interrupt-controller@f8f01000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0xF8F01000 0x1000>,
+ <0xF8F00100 0x100>;
+ };
+
+ slcr: slcr@f8000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "xlnx,zynq-slcr", "syscon", "simple-bus";
+ reg = <0xF8000000 0x1000>;
+ ranges;
+ clkc: clkc@100 {
+ #clock-cells = <1>;
+ compatible = "xlnx,ps7-clkc";
+ fclk-enable = <0xf>;
+ clock-output-names = "armpll", "ddrpll",
+ "iopll", "cpu_6or4x",
+ "cpu_3or2x", "cpu_2x", "cpu_1x",
+ "ddr2x", "ddr3x", "dci",
+ "lqspi", "smc", "pcap", "gem0",
+ "gem1", "fclk0", "fclk1",
+ "fclk2", "fclk3", "can0",
+ "can1", "sdio0", "sdio1",
+ "uart0", "uart1", "spi0",
+ "spi1", "dma", "usb0_aper",
+ "usb1_aper", "gem0_aper",
+ "gem1_aper", "sdio0_aper",
+ "sdio1_aper", "spi0_aper",
+ "spi1_aper", "can0_aper",
+ "can1_aper", "i2c0_aper",
+ "i2c1_aper", "uart0_aper",
+ "uart1_aper", "gpio_aper",
+ "lqspi_aper", "smc_aper",
+ "swdt", "dbg_trc", "dbg_apb";
+ reg = <0x100 0x100>;
+ };
+ };
+ };
+
+};
+
+&dcc {
+ status = "okay";
+};
diff --git a/configs/zynq_cse_nor_defconfig b/configs/zynq_cse_nor_defconfig
new file mode 100644
index 0000000..842d520
--- /dev/null
+++ b/configs/zynq_cse_nor_defconfig
@@ -0,0 +1,50 @@
+CONFIG_ARM=y
+CONFIG_SYS_CONFIG_NAME="zynq_cse"
+CONFIG_ARCH_ZYNQ=y
+CONFIG_SYS_TEXT_BASE=0xFFFC0000
+CONFIG_SPL_STACK_R_ADDR=0x200000
+CONFIG_SYS_MALLOC_LEN=0x1000
+CONFIG_ZYNQ_M29EW_WB_HACK=y
+CONFIG_DEFAULT_DEVICE_TREE="zynq-cse-nor"
+CONFIG_BOOTDELAY=-1
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_SPL=y
+CONFIG_SPL_STACK_R=y
+CONFIG_SYS_PROMPT="Zynq> "
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_CONSOLE is not set
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_BOOTM is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_FDT is not set
+# CONFIG_CMD_GO is not set
+# CONFIG_CMD_RUN is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_SPL is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+# CONFIG_CMD_EDITENV is not set
+# CONFIG_CMD_SAVEENV is not set
+# CONFIG_CMD_ENV_EXISTS is not set
+# CONFIG_CMD_CRC32 is not set
+# CONFIG_CMD_CLK is not set
+# CONFIG_CMD_DM is not set
+# CONFIG_CMD_FPGA is not set
+# CONFIG_CMD_LOADB is not set
+# CONFIG_CMD_LOADS is not set
+# CONFIG_CMD_ECHO is not set
+# CONFIG_CMD_ITEST is not set
+# CONFIG_CMD_SOURCE is not set
+# CONFIG_CMD_SETEXPR is not set
+# CONFIG_CMD_NET is not set
+# CONFIG_CMD_NFS is not set
+# CONFIG_CMD_MISC is not set
+# CONFIG_PARTITIONS is not set
+CONFIG_OF_EMBED=y
+# CONFIG_DM_WARN is not set
+# CONFIG_DM_DEVICE_REMOVE is not set
+CONFIG_SPL_DM_SEQ_ALIAS=y
+# CONFIG_MMC is not set
+CONFIG_MTD_NOR_FLASH=y
+# CONFIG_EFI_LOADER is not set
--
2.7.4
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
