On Mon, 21 Jan 2019 00:54:52 +0000 André Przywara <andre.przyw...@arm.com> wrote:
> On 20/01/2019 19:51, Priit Laes wrote: > > Hi, > > > On Sat, Jan 19, 2019 at 01:30:46AM +0000, Andre Przywara wrote: > >> This series enables the Allwinner MMC driver to drive all SoCs > >> with its DM_MMC variant. We use the gates clock and reset support > >> from the new clock driver, but keep the actual mod clock in its > >> somewhat hackish state. Properly supporting this via the clock > >> driver is a bit more work. The per-compatible variant struct for > >> now only holds the mod clock address (which will go away), but we > >> will need the struct later again for the various timing modes. > >> > >> This allows us to eventually enable DM_MMC for all SoCs, and get > >> rid of the nasty deprecation warning. > >> > >> The first patch adds the MMC clock gates and resets to the clock > >> driver. Patch 2/9 adds support for the A80 MMC config clock, which > >> is a bit special. I can't test this, so please give this a try if > >> you have a board. > >> > >> Patch 3 uses the new clocks in the MMC driver, the following three > >> patches add the remaining compatible strings along with their > >> required mod clock addresses. > >> > >> Patch 7 fixes the Pine64-LTS board, while patch 8 eventually > >> enables everything. Patch 9 is some comment fix to make it easier > >> to reason about what part of the driver is for DM_MMC and which is > >> not. > >> > >> I successfully compiled the HEAD for all 142 Allwinner boards, also > >> compiled all patches for selected boards. > >> > >> This was briefly tested on Pine-H64 (H6), Pine64-LTS (A64), > >> OrangePi PC 2 (H5), OrangePi Zero (H2+) and BananaPi-M1 (A20). > >> > >> Please run it on every board that you can get hold of to give this > >> series a good shake. > > > > Testing with A10 Gemei G9 Tablet, FEL mode is broken: > > > > a) With usb-boot via fel: > > > > I get following error/warning: > > Loading Environment from FAT... Card did not respond to voltage > > select! > > => mmc list > > mmc@1c0f000: 0 > > ### All commands below stalls for a bit (~2 seconds), but return > > nothing => mmc info > > => mmc dev 0 > > => mmc part > > Ah, thanks for mentioning that. Can reproduce this on the Pine64-LTS. > And I was already wondering why we wouldn't need the pinctrl parts I > was working on ... > > So if we boot from SD card, the SPL sets up the pinmux for the SD > pins, and stuff works. For U-Boot proper we rely on board_mmc_init() > to do this for us, but this gets only called for !DM_MMC > configurations. If we boot with a SPL which doesn't initialise the > MMC (booting via FEL or SPI or NAND), the pinmux setup is missing and > it fails. > > If anyone has a clever idea how to fix this without too much hacking > and without bringing in a DM_PINCTRL driver, I am all ears. > I had similar problem with imx6. The DM_PINCTRL seems to be a must-have here. There is a similar problem - driver model tends to re-configure the pinmux configuration in SPL and u-boot proper (also before relocation if asked). > Thanks for testing and the report! > > Cheers, > Andre. > > > > > b) When booting from SD-card [1], card is properly found, > > identified and even partitions are there. > > > > dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk0 seek=8 bs=1024 > > > > > >> This goes on top of current sunxi/master (543049ab5906) and is > >> available on https://github.com/apritzel/u-boot/commits/sunxi-dm. > >> > >> This replaces Jagan's v2 series "mmc: sunxi: Enable DM_MMC" in a > >> more driver model compliant way, borrowing two patches from him. > >> > >> Cheers, > >> Andre. > >> > >> Andre Przywara (7): > >> sunxi: clk: add MMC gates/resets > >> sunxi: clk: A80: add MMC clock support > >> mmc: sunxi: Add DM clk and reset support > >> mmc: sunxi: Add H6 support > >> mmc: sunxi: Add A80 support > >> mmc: sunxi: Honour non-removable property in DT > >> mmc: sunxi: Mark end of DM_MMC #ifdefs > >> > >> Jagan Teki (2): > >> mmc: sunxi: Add missing compatible strings > >> arm: sunxi: Enable DM_MMC > >> > >> arch/arm/Kconfig | 1 + > >> arch/arm/mach-sunxi/Kconfig | 1 - > >> configs/Linksprite_pcDuino3_defconfig | 1 - > >> drivers/clk/sunxi/clk_a10.c | 4 +++ > >> drivers/clk/sunxi/clk_a10s.c | 3 ++ > >> drivers/clk/sunxi/clk_a23.c | 6 ++++ > >> drivers/clk/sunxi/clk_a31.c | 8 +++++ > >> drivers/clk/sunxi/clk_a64.c | 6 ++++ > >> drivers/clk/sunxi/clk_a80.c | 28 ++++++++++++++++- > >> drivers/clk/sunxi/clk_a83t.c | 6 ++++ > >> drivers/clk/sunxi/clk_h3.c | 6 ++++ > >> drivers/clk/sunxi/clk_h6.c | 6 ++++ > >> drivers/clk/sunxi/clk_r40.c | 8 +++++ > >> drivers/mmc/sunxi_mmc.c | 59 > >> +++++++++++++++++++++++++++++------ 14 files changed, 131 > >> insertions(+), 12 deletions(-) > >> > >> -- > >> 2.14.5 > >> > >> -- > >> You received this message because you are subscribed to the Google > >> Groups "linux-sunxi" group. To unsubscribe from this group and > >> stop receiving emails from it, send an email to > >> linux-sunxi+unsubscr...@googlegroups.com. For more options, visit > >> https://groups.google.com/d/optout. > > _______________________________________________ > U-Boot mailing list > U-Boot@lists.denx.de > https://lists.denx.de/listinfo/u-boot Best regards, Lukasz Majewski -- DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lu...@denx.de
pgpAZc7hKAziI.pgp
Description: OpenPGP digital signature
_______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot