This adds initial support for micro-DPU (uDPU) board which is based on
Armada-3720 SoC.
micro-DPU is the single-port FTTdp "distribution point unit" made by Methode
Electronics
which offers complete modularity with replaceable SFP modules both for uplink
and downlink
(G.hn over twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e
cable).
On-board features:
- 512 MiB DDR3
- 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC
- USB 2.0 Type-C connector
- 4GB eMMC
- ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type)
Cc: Luka Perkov <luka.per...@sartura.hr>
Cc: Luis Torres <luis.tor...@methode.com>
Cc: Scott Roberts <scott.robe...@telus.com>
Cc: Paul Arola <paul.ar...@telus.com>
Cc: Chris Packham <judge.pack...@gmail.com>
Signed-off-by: Vladimir Vid <vladimir....@sartura.hr>
---
v3 changes:
- removed MMC_SDHCI_MV driver which was generating error durring the build.
SDHCI_XENON driver is sufficient for the internal eMMC.
- fixed remaining warnings durring the build time (reg properties)
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/armada-3720-uDPU.dts | 201 ++++++++++++++++++++
board/Marvell/mvebu_armada-37xx/MAINTAINERS | 5 +
configs/uDPU_defconfig | 94 +++++++++
4 files changed, 301 insertions(+)
create mode 100644 arch/arm/dts/armada-3720-uDPU.dts
create mode 100644 configs/uDPU_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 5c3225bcbf..9e1e1ad8e9 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -95,6 +95,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += \
armada-3720-db.dtb \
armada-3720-espressobin.dtb \
armada-3720-turris-mox.dtb \
+ armada-3720-uDPU.dts \
armada-375-db.dtb \
armada-388-clearfog.dtb \
armada-388-gp.dtb \
diff --git a/arch/arm/dts/armada-3720-uDPU.dts
b/arch/arm/dts/armada-3720-uDPU.dts
new file mode 100644
index 0000000000..de44e317a6
--- /dev/null
+++ b/arch/arm/dts/armada-3720-uDPU.dts
@@ -0,0 +1,201 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device tree for the uDPU board.
+ * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
+ * Copyright (C) 2016 Marvell
+ * Copyright (C) 2018 Methode
+ * Copyright (C) 2018 Telus
+ *
+ * Vladimir Vid <vladimir....@sartura.hr>
+ */
+
+/dts-v1/;
+
+#include "armada-37xx.dtsi"
+
+/ {
+ model = "Methode uDPU Board";
+ compatible = "methode,udpu";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs = "console=ttyMV0,115200
earlycon=ar3700_uart,0xd0012000";
+ };
+
+ aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ spi0 = &spi0;
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+ };
+
+ mdio: mdio@32004 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+ };
+
+ scsi: scsi {
+ compatible = "marvell,mvebu-scsi";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ max-id = <1>;
+ max-lun = <1>;
+ status = "okay";
+ };
+
+ i2c1: i2c@11080 {
+ compatible = "marvell,armada-3700-i2c", "simple-bus";
+ reg = <0x0 0x11080 0x0 0x80>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ status = "okay";
+ };
+
+ uart1: serial@12200 {
+ compatible = "marvell,armada-3700-uart-ext";
+ reg = <0x0 0x12200 0x0 0x30>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ status = "okay";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ };
+
+ vcc_sd_reg0: regulator@0 {
+ compatible = "regulator-gpio";
+ regulator-name = "vcc_sd0";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-type = "voltage";
+ states = <1800000 0x1
+ 3300000 0x0>;
+ gpios = <&gpiosb 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ sfp_eth0: sfp-eth0 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c0>;
+ los-gpio = <&gpiosb 2 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&gpiosb 3 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&gpiosb 4 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ sfp_eth1: sfp-eth1 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c1>;
+ sfp,ethernet = <ð1>;
+ los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&comphy {
+ phy0 {
+ phy-type = <PHY_TYPE_SGMII1>;
+ phy-speed = <PHY_SPEED_1_25G>;
+ };
+ phy1 {
+ phy-type = <PHY_TYPE_SGMII0>;
+ phy-speed = <PHY_SPEED_1_25G>;
+ };
+
+ phy2 {
+ phy-type = <PHY_TYPE_USB3_HOST1>;
+ phy-speed = <PHY_SPEED_5G>;
+ };
+};
+
+ð0 {
+ pinctrl-0 = <&pcie_pins>;
+ status = "okay";
+ phy-mode = "sgmii";
+ phy = <ðphy0>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+ð1 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phy = <ðphy1>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_quad_pins>;
+ u-boot,dm-pre-reloc;
+
+ spi-flash@0 {
+ u-boot,dm-pre-reloc;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q1024a","n25q512a";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
+ m25p,fast-read;
+
+ partition@0 {
+ label = "uboot";
+ reg = <0 0x400000>;
+ };
+ };
+};
+
+&sdhci1 {
+ non-removable;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ bus-width = <4>;
+ vqmmc-supply = <&vcc_sd_reg0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio_pins>;
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mmccard: mmccard@0 {
+ compatible = "mmc-card";
+ reg = <0>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+};
+
+&usb3 {
+ status = "okay";
+};
diff --git a/board/Marvell/mvebu_armada-37xx/MAINTAINERS
b/board/Marvell/mvebu_armada-37xx/MAINTAINERS
index 9b0afeef10..f2c0a582d7 100644
--- a/board/Marvell/mvebu_armada-37xx/MAINTAINERS
+++ b/board/Marvell/mvebu_armada-37xx/MAINTAINERS
@@ -9,3 +9,8 @@ ESPRESSOBin BOARD
M: Konstantin Porotchkin <kos...@marvell.com>
S: Maintained
F: configs/mvebu_espressobin-88f3720_defconfig
+
+uDPU BOARD
+M: Vladimir Vid <vladimir....@sartura.hr>
+S: Maintained
+F: configs/uDPU_defconfig
diff --git a/configs/uDPU_defconfig b/configs/uDPU_defconfig
new file mode 100644
index 0000000000..53f2b6e746
--- /dev/null
+++ b/configs/uDPU_defconfig
@@ -0,0 +1,94 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_SYS_TEXT_BASE=0x00000000
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TARGET_MVEBU_ARMADA_37XX=y
+CONFIG_DEBUG_UART_BASE=0xd0012000
+CONFIG_DEBUG_UART_CLOCK=25804800
+CONFIG_SMBIOS_PRODUCT_NAME="uDPU"
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_FIT=y
+CONFIG_SPI_BOOT=y
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_ARCH_EARLY_INIT_R=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SYS_PROMPT="uDPU>> "
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_MVEBU_BUBT=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nor0=spi0"
+CONFIG_MTDPARTS_DEFAULT="mtdparts=spi0:4m(uboot),-(rootfs)"
+CONFIG_MAC_PARTITION=y
+CONFIG_DEFAULT_DEVICE_TREE="armada-3720-uDPU"
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_AHCI_MVEBU=y
+CONFIG_CLK=y
+CONFIG_CLK_MVEBU=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_DM_I2C_GPIO=y
+CONFIG_MISC=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_XENON=y
+CONFIG_MTD=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_PHYLIB_10G=y
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_GIGE=y
+CONFIG_E1000=y
+CONFIG_MVNETA=y
+CONFIG_PCI=y
+CONFIG_DM_PCI=y
+CONFIG_PCI_AARDVARK=y
+CONFIG_MVEBU_COMPHY_SUPPORT=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_ARMADA_37XX=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+# CONFIG_SPL_SERIAL_PRESENT is not set
+CONFIG_DEBUG_MVEBU_A3700_UART=y
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_MVEBU_A3700_UART=y
+CONFIG_MVEBU_A3700_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_ETHER_MCS7830=y
+CONFIG_USB_ETHER_RTL8152=y
+CONFIG_USB_ETHER_SMSC95XX=y
+CONFIG_LZO=y
+CONFIG_SPL_LZO=y
--
2.19.0
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
