All socfpga boards except for vining_fpga use DM_I2C. Enable
DM_I2C for this board and set the EEPROM defines via Kconfig
(enabling CONFIG_I2C_EEPROM from MISC).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschm...@gmail.com>
---
Changes in v4:
- fix DM_I2C case: don't call i2c_set_bus_num() since this is
done in cmd/eeprom already
Changes in v3: None
Changes in v2:
- added (this) patch to move socfpga_vining to DM_I2C
board/samtec/vining_fpga/socfpga.c | 9 +--------
configs/socfpga_vining_fpga_defconfig | 8 +++++++-
include/configs/socfpga_common.h | 26 --------------------------
include/configs/socfpga_vining_fpga.h | 9 ---------
4 files changed, 8 insertions(+), 44 deletions(-)
diff --git a/board/samtec/vining_fpga/socfpga.c
b/board/samtec/vining_fpga/socfpga.c
index d99aac6828..efc8ddf162 100644
--- a/board/samtec/vining_fpga/socfpga.c
+++ b/board/samtec/vining_fpga/socfpga.c
@@ -52,14 +52,7 @@ int misc_init_r(void)
u32 serial;
int ret;
- /* EEPROM is at bus 0. */
- ret = i2c_set_bus_num(0);
- if (ret) {
- puts("Cannot select EEPROM I2C bus.\n");
- return 0;
- }
-
- /* EEPROM is at address 0x50. */
+ /* EEPROM is at address 0x50 (at bus CONFIG_SYS_EEPROM_BUS_NUM). */
ret = eeprom_read(0x50, 0, data, sizeof(data));
if (ret) {
puts("Cannot read I2C EEPROM.\n");
diff --git a/configs/socfpga_vining_fpga_defconfig
b/configs/socfpga_vining_fpga_defconfig
index 7b47b111b7..4a7f775337 100644
--- a/configs/socfpga_vining_fpga_defconfig
+++ b/configs/socfpga_vining_fpga_defconfig
@@ -16,8 +16,8 @@ CONFIG_VERSION_VARIABLE=y
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_CMD_ASKENV=y
-CONFIG_CMD_GREPENV=y
CONFIG_CMD_EEPROM=y
+CONFIG_CMD_GREPENV=y
CONFIG_CMD_DFU=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_GPIO=y
@@ -44,6 +44,7 @@ CONFIG_DFU_RAM=y
CONFIG_DFU_SF=y
CONFIG_DM_GPIO=y
CONFIG_DWAPB_GPIO=y
+CONFIG_DM_I2C=y
CONFIG_LED_STATUS=y
CONFIG_LED_STATUS_GPIO=y
CONFIG_LED_STATUS0=y
@@ -55,6 +56,11 @@ CONFIG_LED_STATUS_BIT2=54
CONFIG_LED_STATUS3=y
CONFIG_LED_STATUS_BIT3=65
CONFIG_LED_STATUS_CMD=y
+CONFIG_MISC=y
+CONFIG_I2C_EEPROM=y
+CONFIG_SYS_I2C_EEPROM_ADDR=0x50
+CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3
+CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=70
CONFIG_DM_MMC=y
CONFIG_MMC_DW=y
CONFIG_MTD_DEVICE=y
diff --git a/include/configs/socfpga_common.h b/include/configs/socfpga_common.h
index a501b5209f..a65fc804e3 100644
--- a/include/configs/socfpga_common.h
+++ b/include/configs/socfpga_common.h
@@ -149,32 +149,6 @@
#define CONFIG_SYS_NAND_DATA_BASE SOCFPGA_NANDDATA_ADDRESS
#endif
-/*
- * I2C support
- */
-#ifndef CONFIG_DM_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_BASE SOCFPGA_I2C0_ADDRESS
-#define CONFIG_SYS_I2C_BASE1 SOCFPGA_I2C1_ADDRESS
-#define CONFIG_SYS_I2C_BASE2 SOCFPGA_I2C2_ADDRESS
-#define CONFIG_SYS_I2C_BASE3 SOCFPGA_I2C3_ADDRESS
-/* Using standard mode which the speed up to 100Kb/s */
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SPEED1 100000
-#define CONFIG_SYS_I2C_SPEED2 100000
-#define CONFIG_SYS_I2C_SPEED3 100000
-/* Address of device when used as slave */
-#define CONFIG_SYS_I2C_SLAVE 0x02
-#define CONFIG_SYS_I2C_SLAVE1 0x02
-#define CONFIG_SYS_I2C_SLAVE2 0x02
-#define CONFIG_SYS_I2C_SLAVE3 0x02
-#ifndef __ASSEMBLY__
-/* Clock supplied to I2C controller in unit of MHz */
-unsigned int cm_get_l4_sp_clk_hz(void);
-#define IC_CLK (cm_get_l4_sp_clk_hz() / 1000000)
-#endif
-#endif /* CONFIG_DM_I2C */
-
/*
* QSPI support
*/
diff --git a/include/configs/socfpga_vining_fpga.h
b/include/configs/socfpga_vining_fpga.h
index 5517ed722d..0e547a1295 100644
--- a/include/configs/socfpga_vining_fpga.h
+++ b/include/configs/socfpga_vining_fpga.h
@@ -16,15 +16,6 @@
#define CONFIG_LOADADDR 0x01000000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-/* I2C EEPROM */
-#ifdef CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_I2C_EEPROM_BUS 0
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
-#endif
-
/*
* Status LEDs:
* 0 ... Top Green
--
2.17.1
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
