CRS305-1G-4S has a switch chip with an integrated CPU (98DX3236) and like some
of the
other simillar boards requires bin_hdr. bin_hdr (DDR3 init stage) is currently
retrieved
from the stock bootloader and compiled into the kwb image.
Adds support for U-Boot, enable UART, SPI, Winbond SPI flash chip support and
writing env to SPI flash.
arch/arm/dts: Remove unused parameters in DTS for crs305-1g-4s
arch/arm/mach-mvebu: Set the proper processor for crs305-1g-4s (98DX3236)
Signed-off-by: Luka Kovacic <m...@lukakovacic.xyz>
---
arch/arm/dts/Makefile | 3 +-
.../dts/armada-xp-crs305-1g-4s-u-boot.dtsi | 13 +++
arch/arm/dts/armada-xp-crs305-1g-4s.dts | 110 ++++++++++++++++++
arch/arm/mach-mvebu/Kconfig | 7 ++
board/mikrotik/crs305-1g-4s/.gitignore | 1 +
board/mikrotik/crs305-1g-4s/MAINTAINERS | 7 ++
board/mikrotik/crs305-1g-4s/Makefile | 14 +++
board/mikrotik/crs305-1g-4s/README | 23 ++++
board/mikrotik/crs305-1g-4s/binary.0 | 11 ++
board/mikrotik/crs305-1g-4s/crs305-1g-4s.c | 68 +++++++++++
board/mikrotik/crs305-1g-4s/kwbimage.cfg.in | 12 ++
configs/crs305-1g-4s_defconfig | 51 ++++++++
include/configs/crs305-1g-4s.h | 37 ++++++
13 files changed, 356 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/dts/armada-xp-crs305-1g-4s-u-boot.dtsi
create mode 100644 arch/arm/dts/armada-xp-crs305-1g-4s.dts
create mode 100644 board/mikrotik/crs305-1g-4s/.gitignore
create mode 100644 board/mikrotik/crs305-1g-4s/MAINTAINERS
create mode 100644 board/mikrotik/crs305-1g-4s/Makefile
create mode 100644 board/mikrotik/crs305-1g-4s/README
create mode 100644 board/mikrotik/crs305-1g-4s/binary.0
create mode 100644 board/mikrotik/crs305-1g-4s/crs305-1g-4s.c
create mode 100644 board/mikrotik/crs305-1g-4s/kwbimage.cfg.in
create mode 100644 configs/crs305-1g-4s_defconfig
create mode 100644 include/configs/crs305-1g-4s.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index dfa5b02958..f463485149 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -161,7 +161,8 @@ dtb-$(CONFIG_ARCH_MVEBU) += \
armada-38x-controlcenterdc.dtb \
armada-385-atl-x530.dtb \
armada-385-atl-x530DP.dtb \
- armada-xp-db-xc3-24g4xg.dtb
+ armada-xp-db-xc3-24g4xg.dtb \
+ armada-xp-crs305-1g-4s.dtb
dtb-$(CONFIG_ARCH_UNIPHIER_LD11) += \
uniphier-ld11-global.dtb \
diff --git a/arch/arm/dts/armada-xp-crs305-1g-4s-u-boot.dtsi
b/arch/arm/dts/armada-xp-crs305-1g-4s-u-boot.dtsi
new file mode 100644
index 0000000000..8576a02730
--- /dev/null
+++ b/arch/arm/dts/armada-xp-crs305-1g-4s-u-boot.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+&uart0 {
+ u-boot,dm-pre-reloc;
+};
+
+&spi0 {
+ u-boot,dm-pre-reloc;
+
+ spi-flash@0 {
+ u-boot,dm-pre-reloc;
+ };
+};
diff --git a/arch/arm/dts/armada-xp-crs305-1g-4s.dts
b/arch/arm/dts/armada-xp-crs305-1g-4s.dts
new file mode 100644
index 0000000000..1116f5c96c
--- /dev/null
+++ b/arch/arm/dts/armada-xp-crs305-1g-4s.dts
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for CRS305-1G-4S board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * Based on armada-xp-db.dts
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx3236.dtsi"
+#include "armada-xp-crs305-1g-4s-u-boot.dtsi"
+
+/ {
+ model = "CRS305-1G-4S";
+ compatible = "marvell,armadaxp-98dx3236", "marvell,armadaxp-mv78260",
"marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ aliases {
+ spi0 = &spi0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
+ };
+};
+
+&L2 {
+ arm,parity-enable;
+ marvell,ecc-enable;
+};
+
+&devbus_bootcs {
+ status = "okay";
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <16>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-flash", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <108000000>;
+ m25p,fast-read;
+
+ partition@u-boot {
+ reg = <0x00000000 0x00100000>;
+ label = "u-boot";
+ };
+ partition@u-boot-env {
+ reg = <0x00100000 0x00040000>;
+ label = "u-boot-env";
+ };
+ partition@unused {
+ reg = <0x00140000 0x00ec0000>;
+ label = "unused";
+ };
+
+ };
+};
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index f99bd3bf65..1d49d49203 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -157,6 +157,10 @@ config TARGET_DB_XC3_24G4XG
bool "Support DB-XC3-24G4XG"
select 98DX3336
+config TARGET_CRS305_1G_4S
+ bool "Support CRS305-1G-4S"
+ select 98DX3236
+
endchoice
config SYS_BOARD
@@ -176,6 +180,7 @@ config SYS_BOARD
default "a38x" if TARGET_CONTROLCENTERDC
default "x530" if TARGET_X530
default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG
+ default "crs305-1g-4s" if TARGET_CRS305_1G_4S
config SYS_CONFIG_NAME
default "clearfog" if TARGET_CLEARFOG
@@ -194,6 +199,7 @@ config SYS_CONFIG_NAME
default "controlcenterdc" if TARGET_CONTROLCENTERDC
default "x530" if TARGET_X530
default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG
+ default "crs305-1g-4s" if TARGET_CRS305_1G_4S
config SYS_VENDOR
default "Marvell" if TARGET_DB_MV784MP_GP
@@ -211,6 +217,7 @@ config SYS_VENDOR
default "CZ.NIC" if TARGET_TURRIS_MOX
default "gdsys" if TARGET_CONTROLCENTERDC
default "alliedtelesis" if TARGET_X530
+ default "mikrotik" if TARGET_CRS305_1G_4S
config SYS_SOC
default "mvebu"
diff --git a/board/mikrotik/crs305-1g-4s/.gitignore
b/board/mikrotik/crs305-1g-4s/.gitignore
new file mode 100644
index 0000000000..775b9346b8
--- /dev/null
+++ b/board/mikrotik/crs305-1g-4s/.gitignore
@@ -0,0 +1 @@
+kwbimage.cfg
diff --git a/board/mikrotik/crs305-1g-4s/MAINTAINERS
b/board/mikrotik/crs305-1g-4s/MAINTAINERS
new file mode 100644
index 0000000000..3823489600
--- /dev/null
+++ b/board/mikrotik/crs305-1g-4s/MAINTAINERS
@@ -0,0 +1,7 @@
+CRS305-1G-4S BOARD
+M: Luka Kovacic <m...@lukakovacic.xyz>
+S: Maintained
+F: board/mikrotik/crs305-1g-4s/
+F: include/configs/crs305-1g-4s.h
+F: configs/crs305-1g-4s_defconfig
+F: arch/arm/dts/armada-xp-crs305-1g-4s.dts
diff --git a/board/mikrotik/crs305-1g-4s/Makefile
b/board/mikrotik/crs305-1g-4s/Makefile
new file mode 100644
index 0000000000..895331beb8
--- /dev/null
+++ b/board/mikrotik/crs305-1g-4s/Makefile
@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2015 Stefan Roese <s...@denx.de>
+
+obj-y := crs305-1g-4s.o
+extra-y := kwbimage.cfg
+
+quiet_cmd_sed = SED $@
+ cmd_sed = sed $(SEDFLAGS_$(@F)) $< >$(dir $<)$(@F)
+
+SEDFLAGS_kwbimage.cfg =-e "s|^BINARY.*|BINARY $(srctree)/$(@D)/binary.0
0000005b 00000068|"
+$(src)/kwbimage.cfg: $(src)/kwbimage.cfg.in include/autoconf.mk \
+ include/config/auto.conf
+ $(call if_changed,sed)
diff --git a/board/mikrotik/crs305-1g-4s/README
b/board/mikrotik/crs305-1g-4s/README
new file mode 100644
index 0000000000..f420aabfbf
--- /dev/null
+++ b/board/mikrotik/crs305-1g-4s/README
@@ -0,0 +1,23 @@
+MikroTik CRS305-1G-4S+IN
+========================
+
+CRS305-1G-4S+IN is a 4x SFP+ switch with a Gigabit Ethernet port for
management.
+Specifications:
+ - Marvell Prestera 98DX3236 switch with an integrated ARMv7 CPU
+ - 512 MB DDR3 RAM
+ - UART @ 115200bps
+ - 4x SFP+
+ - Gigabit Ethernet (AR8033)
+ - 16 MB SPI flash (Winbond 25Q128JVSM)
+
+Currently supported hardware:
+ - UART boot (using kwboot) and console
+ - SPI boot, environment and load kernel
+
+Planned:
+ - Gigabit Ethernet support
+
+Getting binary.0
+================
+binary.0 (DDR3 init phase) can be retrieved/extracted from the integrated
bootloader on the SPI flash.
+Then binary.0 can be replaced with the extracted blob.
diff --git a/board/mikrotik/crs305-1g-4s/binary.0
b/board/mikrotik/crs305-1g-4s/binary.0
new file mode 100644
index 0000000000..8dd687286a
--- /dev/null
+++ b/board/mikrotik/crs305-1g-4s/binary.0
@@ -0,0 +1,11 @@
+--------
+WARNING:
+--------
+This file should contain the bin_hdr generated by the original Marvell
+U-Boot implementation. As this is currently not included in this
+U-Boot version, we have added this placeholder, so that the U-Boot
+image can be generated without errors.
+
+If you have a known to be working bin_hdr for your board, then you
+just need to replace this text file here with the binary header
+and recompile U-Boot.
diff --git a/board/mikrotik/crs305-1g-4s/crs305-1g-4s.c
b/board/mikrotik/crs305-1g-4s/crs305-1g-4s.c
new file mode 100644
index 0000000000..cae428ffd0
--- /dev/null
+++ b/board/mikrotik/crs305-1g-4s/crs305-1g-4s.c
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2015 Stefan Roese <s...@denx.de>
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/gpio.h>
+#include <linux/mbus.h>
+#include <linux/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * These values and defines are taken from the Marvell U-Boot version
+ * "u-boot-2013.01-2016_T1.0.eng_drop_v6"
+ */
+#define DB_DX_AC3_GPP_OUT_ENA_LOW (~(BIT(0) | BIT(2) | BIT(3) | BIT(4) |
BIT(6) | BIT(12) \
+ | BIT(13) | BIT(16) | BIT(17) | BIT(20)
| BIT(29) | BIT(30)))
+#define DB_DX_AC3_GPP_OUT_ENA_MID (~(0))
+#define DB_DX_AC3_GPP_OUT_VAL_LOW (BIT(0) | BIT(2) | BIT(3) | BIT(4) |
BIT(6) | BIT(12) \
+ | BIT(13) | BIT(16) | BIT(17) | BIT(20)
| BIT(29) | BIT(30))
+#define DB_DX_AC3_GPP_OUT_VAL_MID 0x0
+#define DB_DX_AC3_GPP_POL_LOW 0x0
+#define DB_DX_AC3_GPP_POL_MID 0x0
+
+int board_early_init_f(void)
+{
+ /* Configure MPP */
+ writel(0x00142222, MVEBU_MPP_BASE + 0x00);
+ writel(0x11122000, MVEBU_MPP_BASE + 0x04);
+ writel(0x44444004, MVEBU_MPP_BASE + 0x08);
+ writel(0x14444444, MVEBU_MPP_BASE + 0x0c);
+ writel(0x00000001, MVEBU_MPP_BASE + 0x10);
+
+ /* Set GPP Out value */
+ writel(DB_DX_AC3_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
+ writel(DB_DX_AC3_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
+
+ /* Set GPP Polarity */
+ writel(DB_DX_AC3_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
+ writel(DB_DX_AC3_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
+
+ /* Set GPP Out Enable */
+ writel(DB_DX_AC3_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
+ writel(DB_DX_AC3_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+ return 0;
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+ puts("Board: " CONFIG_SYS_BOARD "\n");
+
+ return 0;
+}
+#endif
diff --git a/board/mikrotik/crs305-1g-4s/kwbimage.cfg.in
b/board/mikrotik/crs305-1g-4s/kwbimage.cfg.in
new file mode 100644
index 0000000000..2dbbbd0246
--- /dev/null
+++ b/board/mikrotik/crs305-1g-4s/kwbimage.cfg.in
@@ -0,0 +1,12 @@
+#
+# Copyright (C) 2014 Stefan Roese <s...@denx.de>
+#
+
+# Armada XP uses version 1 image format
+VERSION 1
+
+# Boot Media configurations
+BOOT_FROM spi
+
+# Binary Header (bin_hdr) with DDR3 training code
+BINARY board/mikrotik/crs305-1g-4s/binary.0 0000005b 00000068
diff --git a/configs/crs305-1g-4s_defconfig b/configs/crs305-1g-4s_defconfig
new file mode 100644
index 0000000000..e5c83f7bb4
--- /dev/null
+++ b/configs/crs305-1g-4s_defconfig
@@ -0,0 +1,51 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_SYS_TEXT_BASE=0x00800000
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TARGET_CRS305_1G_4S=y
+CONFIG_BUILD_TARGET="u-boot.kwb"
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_SYS_ALT_MEMTEST=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_I2C=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+# CONFIG_CMD_USB is not set
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_UBI=y
+CONFIG_DEFAULT_DEVICE_TREE="armada-xp-crs305-1g-4s"
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_BLK=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MVTWSI=y
+# CONFIG_MMC is not set
+CONFIG_MTD=y
+CONFIG_MTD_DEVICE=y
+# CONFIG_NAND is not set
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_SST=y
+CONFIG_SPI_FLASH_WINBOND=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PCI=y
+CONFIG_PCI_MVEBU=y
+CONFIG_SYS_NS16550=y
+CONFIG_KIRKWOOD_SPI=y
+# CONFIG_USB is not set
+# CONFIG_DM_USB is not set
+# CONFIG_USB_EHCI_HCD is not set
+# CONFIG_USB_STORAGE is not set
+# CONFIG_USB_HOST_ETHER is not set
diff --git a/include/configs/crs305-1g-4s.h b/include/configs/crs305-1g-4s.h
new file mode 100644
index 0000000000..c73cb99b1b
--- /dev/null
+++ b/include/configs/crs305-1g-4s.h
@@ -0,0 +1,37 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2014 Stefan Roese <s...@denx.de>
+ */
+
+#ifndef _CONFIG_CRS305_1G_4S_H
+#define _CONFIG_CRS305_1G_4S_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+
+#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
+#define CONFIG_SYS_TCLK 200000000 /* 200MHz */
+
+/* USB/EHCI configuration */
+#define CONFIG_EHCI_IS_TDI
+
+/* Environment in SPI NOR flash */
+#define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */
+#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */
+#define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */
+
+/* Keep device tree and initrd in lower memory so the kernel can access them */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "fdt_high=0x10000000\0" \
+ "initrd_high=0x10000000\0"
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+#undef CONFIG_SYS_MAXARGS
+#define CONFIG_SYS_MAXARGS 96
+
+#endif /* _CONFIG_CRS305_1G_4S_H */
--
2.20.1
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
