> Subject: [v3, 4/5] mmc: fsl_esdhc: drop i.MX code
>
> Dropped i.MX code which couldn't be reused.
>
> Signed-off-by: Yangbo Lu <yangbo...@nxp.com>
> ---
> Changes for v2:
> - Added this patch.
> Changes for v3:
> - Rebased.
> ---
> drivers/mmc/fsl_esdhc.c | 609 ++--------------------------------------
> include/fsl_esdhc.h | 57 ----
> 2 files changed, 21 insertions(+), 645 deletions(-)
>
> diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c index
> 1b7de74a72..3f4f75ae4c 100644
> --- a/drivers/mmc/fsl_esdhc.c
> +++ b/drivers/mmc/fsl_esdhc.c
> @@ -16,14 +16,11 @@
> #include <hwconfig.h>
> #include <mmc.h>
> #include <part.h>
> -#include <power/regulator.h>
> #include <malloc.h>
> #include <fsl_esdhc.h>
> #include <fdt_support.h>
> #include <asm/io.h>
> #include <dm.h>
> -#include <asm-generic/gpio.h>
> -#include <dm/pinctrl.h>
>
> DECLARE_GLOBAL_DATA_PTR;
>
> @@ -33,8 +30,6 @@ DECLARE_GLOBAL_DATA_PTR;
> IRQSTATEN_CIE | IRQSTATEN_DTOE | IRQSTATEN_DCE
> | \
> IRQSTATEN_DEBE | IRQSTATEN_BRR | IRQSTATEN_BWR |
> \
> IRQSTATEN_DINT)
> -#define MAX_TUNING_LOOP 40
> -
> struct fsl_esdhc {
> uint dsaddr; /* SDMA system address register */
> uint blkattr; /* Block attributes register */
> @@ -54,37 +49,20 @@ struct fsl_esdhc {
> uint autoc12err; /* Auto CMD error status register */
> uint hostcapblt; /* Host controller capabilities register */
> uint wml; /* Watermark level register */
> - uint mixctrl; /* For USDHC */
> - char reserved1[4]; /* reserved */
> + char reserved1[8]; /* reserved */
> uint fevt; /* Force event register */
> uint admaes; /* ADMA error status register */
> uint adsaddr; /* ADMA system address register */
> - char reserved2[4];
> - uint dllctrl;
> - uint dllstat;
> - uint clktunectrlstatus;
> - char reserved3[4];
> - uint strobe_dllctrl;
> - uint strobe_dllstat;
> - char reserved4[72];
> - uint vendorspec;
> - uint mmcboot;
> - uint vendorspec2;
> - uint tuning_ctrl; /* on i.MX6/7/8 */
> - char reserved5[44];
> + char reserved2[160];
> uint hostver; /* Host controller version register */
> - char reserved6[4]; /* reserved */
> + char reserved3[4]; /* reserved */
> uint dmaerraddr; /* DMA error address register */
> - char reserved7[4]; /* reserved */
> + char reserved4[4]; /* reserved */
> uint dmaerrattr; /* DMA error attribute register */
> - char reserved8[4]; /* reserved */
> + char reserved5[4]; /* reserved */
> uint hostcapblt2; /* Host controller capabilities register 2 */
> - char reserved9[8]; /* reserved */
> - uint tcr; /* Tuning control register */
> - char reserved10[28]; /* reserved */
> - uint sddirctl; /* SD direction control register */
> - char reserved11[712];/* reserved */
> - uint scr; /* eSDHC control register */
> + char reserved6[756]; /* reserved */
> + uint esdhcctl; /* eSDHC control register */
> };
>
> struct fsl_esdhc_plat {
> @@ -92,11 +70,6 @@ struct fsl_esdhc_plat {
> struct mmc mmc;
> };
>
> -struct esdhc_soc_data {
> - u32 flags;
> - u32 caps;
> -};
> -
> /**
> * struct fsl_esdhc_priv
> *
> @@ -109,13 +82,6 @@ struct esdhc_soc_data {
> * @dev: pointer for the device
> * @non_removable: 0: removable; 1: non-removable
> * @wp_enable: 1: enable checking wp; 0: no check
> - * @vs18_enable: 1: use 1.8V voltage; 0: use 3.3V
> - * @flags: ESDHC_FLAG_xx in include/fsl_esdhc.h
> - * @caps: controller capabilities
> - * @tuning_step: tuning step setting in tuning_ctrl register
> - * @start_tuning_tap: the start point for tuning in tuning_ctrl register
> - * @strobe_dll_delay_target: settings in strobe_dllctrl
> - * @signal_voltage: indicating the current voltage
> * @cd_gpio: gpio for card detection
> * @wp_gpio: gpio for write protection
> */
> @@ -124,7 +90,6 @@ struct fsl_esdhc_priv {
> unsigned int sdhc_clk;
> struct clk per_clk;
> unsigned int clock;
> - unsigned int mode;
> unsigned int bus_width;
> #if !CONFIG_IS_ENABLED(BLK)
> struct mmc *mmc;
> @@ -132,21 +97,6 @@ struct fsl_esdhc_priv {
> struct udevice *dev;
> int non_removable;
> int wp_enable;
> - int vs18_enable;
> - u32 flags;
> - u32 caps;
> - u32 tuning_step;
> - u32 tuning_start_tap;
> - u32 strobe_dll_delay_target;
> - u32 signal_voltage;
> -#if IS_ENABLED(CONFIG_DM_REGULATOR)
> - struct udevice *vqmmc_dev;
> - struct udevice *vmmc_dev;
> -#endif
> -#ifdef CONFIG_DM_GPIO
> - struct gpio_desc cd_gpio;
> - struct gpio_desc wp_gpio;
> -#endif
> };
>
> /* Return the XFERTYP flags for a given command and data packet */ @@
> -258,8 +208,7 @@ static int esdhc_setup_data(struct fsl_esdhc_priv *priv,
> struct mmc *mmc, {
> int timeout;
> struct fsl_esdhc *regs = priv->esdhc_regs; -#if
> defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
> - defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
> +#if defined(CONFIG_FSL_LAYERSCAPE)
> dma_addr_t addr;
> #endif
> uint wml_value;
> @@ -272,8 +221,7 @@ static int esdhc_setup_data(struct fsl_esdhc_priv
> *priv, struct mmc *mmc,
>
> esdhc_clrsetbits32(®s->wml, WML_RD_WML_MASK,
> wml_value); #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO -#if
> defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
> - defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
> +#if defined(CONFIG_FSL_LAYERSCAPE)
> addr = virt_to_phys((void *)(data->dest));
> if (upper_32_bits(addr))
> printf("Error found for upper 32 bits\n"); @@ -297,20
> +245,12
> @@ static int esdhc_setup_data(struct fsl_esdhc_priv *priv, struct mmc
> *mmc,
> printf("\nThe SD card is locked. Can not write
> to a locked
> card.\n\n");
> return -ETIMEDOUT;
> }
> - } else {
> -#ifdef CONFIG_DM_GPIO
> - if (dm_gpio_is_valid(&priv->wp_gpio) &&
> dm_gpio_get_value(&priv->wp_gpio)) {
> - printf("\nThe SD card is locked. Can not write
> to a locked
> card.\n\n");
> - return -ETIMEDOUT;
> - }
> -#endif
> }
>
> esdhc_clrsetbits32(®s->wml, WML_WR_WML_MASK,
> wml_value << 16);
> #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO
> -#if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
> - defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
> +#if defined(CONFIG_FSL_LAYERSCAPE)
> addr = virt_to_phys((void *)(data->src));
> if (upper_32_bits(addr))
> printf("Error found for upper 32 bits\n"); @@ -375,8
> +315,7
> @@ static void check_and_invalidate_dcache_range
> unsigned end = 0;
> unsigned size = roundup(ARCH_DMA_MINALIGN,
> data->blocks*data->blocksize);
> -#if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
> - defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
> +#if defined(CONFIG_FSL_LAYERSCAPE)
> dma_addr_t addr;
>
> addr = virt_to_phys((void *)(data->dest)); @@ -466,14 +405,7 @@ static
> int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc,
>
> /* Send the command */
> esdhc_write32(®s->cmdarg, cmd->cmdarg); -#if
> defined(CONFIG_FSL_USDHC)
> - esdhc_write32(®s->mixctrl,
> - (esdhc_read32(®s->mixctrl) & 0xFFFFFF80) | (xfertyp & 0x7F)
> - | (mmc->ddr_mode ? XFERTYP_DDREN : 0));
> - esdhc_write32(®s->xfertyp, xfertyp & 0xFFFF0000);
> -#else
> esdhc_write32(®s->xfertyp, xfertyp); -#endif
>
> if ((cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK) ||
> (cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200))
> @@ -500,15 +432,6 @@ static int esdhc_send_cmd_common(struct
> fsl_esdhc_priv *priv, struct mmc *mmc,
> goto out;
> }
>
> - /* Switch voltage to 1.8V if CMD11 succeeded */
> - if (cmd->cmdidx == SD_CMD_SWITCH_UHS18V) {
> - esdhc_setbits32(®s->vendorspec,
> ESDHC_VENDORSPEC_VSELECT);
> -
> - printf("Run CMD11 1.8V switch\n");
> - /* Sleep for 5 ms - max time for card to switch to 1.8V */
> - udelay(5000);
> - }
> -
> /* Workaround for ESDHC errata ENGcm03648 */
> if (!data && (cmd->resp_type & MMC_RSP_BUSY)) {
> int timeout = 6000;
> @@ -596,10 +519,6 @@ out:
> while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTD))
> ;
> }
> -
> - /* If this was CMD11, then notify that power cycle is needed */
> - if (cmd->cmdidx == SD_CMD_SWITCH_UHS18V)
> - printf("CMD11 to switch to 1.8V mode failed, card
> requires
> power cycle.\n");
> }
>
> esdhc_write32(®s->irqstat, -1);
> @@ -611,62 +530,32 @@ static void set_sysctl(struct fsl_esdhc_priv *priv,
> struct mmc *mmc, uint clock) {
> struct fsl_esdhc *regs = priv->esdhc_regs;
> int div = 1;
> -#ifdef ARCH_MXC
> -#ifdef CONFIG_MX53
> - /* For i.MX53 eSDHCv3, SYSCTL.SDCLKFS may not be set to 0. */
> - int pre_div = (regs == (struct fsl_esdhc *)MMC_SDHC3_BASE_ADDR) ? 2 :
> 1;
> -#else
> - int pre_div = 1;
> -#endif
> -#else
> int pre_div = 2;
> -#endif
> + int ddr_pre_div = mmc->ddr_mode ? 2 : 1;
> int sdhc_clk = priv->sdhc_clk;
> uint clk;
>
> - /*
> - * For ddr mode, usdhc need to enable DDR mode first, after select
> - * this DDR mode, usdhc will automatically divide the usdhc clock
> - */
> - if (mmc->ddr_mode) {
> - writel(readl(®s->mixctrl) | MIX_CTRL_DDREN, ®s->mixctrl);
> - sdhc_clk >>= 1;
> - }
> -
> if (clock < mmc->cfg->f_min)
> clock = mmc->cfg->f_min;
>
> - if (sdhc_clk / 16 > clock) {
> - for (; pre_div < 256; pre_div *= 2)
> - if ((sdhc_clk / pre_div) <= (clock * 16))
> - break;
> - } else
> - pre_div = 1;
> + while (sdhc_clk / (16 * pre_div * ddr_pre_div) > clock && pre_div < 256)
> + pre_div *= 2;
>
> - for (div = 1; div <= 16; div++)
> - if ((sdhc_clk / (div * pre_div)) <= clock)
> - break;
> + while (sdhc_clk / (div * pre_div * ddr_pre_div) > clock && div < 16)
> + div++;
>
> pre_div >>= 1;
> div -= 1;
>
> clk = (pre_div << 8) | (div << 4);
>
> -#ifdef CONFIG_FSL_USDHC
> - esdhc_clrbits32(®s->vendorspec, VENDORSPEC_CKEN);
> -#else
> esdhc_clrbits32(®s->sysctl, SYSCTL_CKEN); -#endif
>
> esdhc_clrsetbits32(®s->sysctl, SYSCTL_CLOCK_MASK, clk);
>
> udelay(10000);
>
> -#ifdef CONFIG_FSL_USDHC
> - esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN |
> VENDORSPEC_CKEN);
> -#else
> esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_CKEN); -#endif
>
> priv->clock = clock;
> }
> @@ -700,317 +589,20 @@ static void esdhc_clock_control(struct
> fsl_esdhc_priv *priv, bool enable) } #endif
>
> -#ifdef MMC_SUPPORTS_TUNING
> -static int esdhc_change_pinstate(struct udevice *dev) -{
> - struct fsl_esdhc_priv *priv = dev_get_priv(dev);
> - int ret;
> -
> - switch (priv->mode) {
> - case UHS_SDR50:
> - case UHS_DDR50:
> - ret = pinctrl_select_state(dev, "state_100mhz");
> - break;
> - case UHS_SDR104:
> - case MMC_HS_200:
> - case MMC_HS_400:
> - ret = pinctrl_select_state(dev, "state_200mhz");
> - break;
> - default:
> - ret = pinctrl_select_state(dev, "default");
> - break;
> - }
> -
> - if (ret)
> - printf("%s %d error\n", __func__, priv->mode);
> -
> - return ret;
> -}
> -
> -static void esdhc_reset_tuning(struct mmc *mmc) -{
> - struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
> - struct fsl_esdhc *regs = priv->esdhc_regs;
> -
> - if (priv->flags & ESDHC_FLAG_USDHC) {
> - if (priv->flags & ESDHC_FLAG_STD_TUNING) {
> - esdhc_clrbits32(®s->autoc12err,
> - MIX_CTRL_SMPCLK_SEL |
> - MIX_CTRL_EXE_TUNE);
> - }
> - }
> -}
> -
> -static void esdhc_set_strobe_dll(struct mmc *mmc) -{
> - struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
> - struct fsl_esdhc *regs = priv->esdhc_regs;
> - u32 val;
> -
> - if (priv->clock > ESDHC_STROBE_DLL_CLK_FREQ) {
> - writel(ESDHC_STROBE_DLL_CTRL_RESET, ®s->strobe_dllctrl);
> -
> - /*
> - * enable strobe dll ctrl and adjust the delay target
> - * for the uSDHC loopback read clock
> - */
> - val = ESDHC_STROBE_DLL_CTRL_ENABLE |
> - (priv->strobe_dll_delay_target <<
> - ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
> - writel(val, ®s->strobe_dllctrl);
> - /* wait 1us to make sure strobe dll status register stable */
> - mdelay(1);
> - val = readl(®s->strobe_dllstat);
> - if (!(val & ESDHC_STROBE_DLL_STS_REF_LOCK))
> - pr_warn("HS400 strobe DLL status REF not lock!\n");
> - if (!(val & ESDHC_STROBE_DLL_STS_SLV_LOCK))
> - pr_warn("HS400 strobe DLL status SLV not lock!\n");
> - }
> -}
> -
> -static int esdhc_set_timing(struct mmc *mmc) -{
> - struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
> - struct fsl_esdhc *regs = priv->esdhc_regs;
> - u32 mixctrl;
> -
> - mixctrl = readl(®s->mixctrl);
> - mixctrl &= ~(MIX_CTRL_DDREN | MIX_CTRL_HS400_EN);
> -
> - switch (mmc->selected_mode) {
> - case MMC_LEGACY:
> - case SD_LEGACY:
> - esdhc_reset_tuning(mmc);
> - writel(mixctrl, ®s->mixctrl);
> - break;
> - case MMC_HS_400:
> - mixctrl |= MIX_CTRL_DDREN | MIX_CTRL_HS400_EN;
> - writel(mixctrl, ®s->mixctrl);
> - esdhc_set_strobe_dll(mmc);
> - break;
> - case MMC_HS:
> - case MMC_HS_52:
> - case MMC_HS_200:
> - case SD_HS:
> - case UHS_SDR12:
> - case UHS_SDR25:
> - case UHS_SDR50:
> - case UHS_SDR104:
> - writel(mixctrl, ®s->mixctrl);
> - break;
> - case UHS_DDR50:
> - case MMC_DDR_52:
> - mixctrl |= MIX_CTRL_DDREN;
> - writel(mixctrl, ®s->mixctrl);
> - break;
> - default:
> - printf("Not supported %d\n", mmc->selected_mode);
> - return -EINVAL;
> - }
> -
> - priv->mode = mmc->selected_mode;
> -
> - return esdhc_change_pinstate(mmc->dev);
> -}
> -
> -static int esdhc_set_voltage(struct mmc *mmc) -{
> - struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
> - struct fsl_esdhc *regs = priv->esdhc_regs;
> - int ret;
> -
> - priv->signal_voltage = mmc->signal_voltage;
> - switch (mmc->signal_voltage) {
> - case MMC_SIGNAL_VOLTAGE_330:
> - if (priv->vs18_enable)
> - return -EIO;
> -#if CONFIG_IS_ENABLED(DM_REGULATOR)
> - if (!IS_ERR_OR_NULL(priv->vqmmc_dev)) {
> - ret = regulator_set_value(priv->vqmmc_dev, 3300000);
> - if (ret) {
> - printf("Setting to 3.3V error");
> - return -EIO;
> - }
> - /* Wait for 5ms */
> - mdelay(5);
> - }
> -#endif
> -
> - esdhc_clrbits32(®s->vendorspec,
> ESDHC_VENDORSPEC_VSELECT);
> - if (!(esdhc_read32(®s->vendorspec) &
> - ESDHC_VENDORSPEC_VSELECT))
> - return 0;
> -
> - return -EAGAIN;
> - case MMC_SIGNAL_VOLTAGE_180:
> -#if CONFIG_IS_ENABLED(DM_REGULATOR)
> - if (!IS_ERR_OR_NULL(priv->vqmmc_dev)) {
> - ret = regulator_set_value(priv->vqmmc_dev, 1800000);
> - if (ret) {
> - printf("Setting to 1.8V error");
> - return -EIO;
> - }
> - }
> -#endif
> - esdhc_setbits32(®s->vendorspec,
> ESDHC_VENDORSPEC_VSELECT);
> - if (esdhc_read32(®s->vendorspec) &
> ESDHC_VENDORSPEC_VSELECT)
> - return 0;
> -
> - return -EAGAIN;
> - case MMC_SIGNAL_VOLTAGE_120:
> - return -ENOTSUPP;
> - default:
> - return 0;
> - }
> -}
> -
> -static void esdhc_stop_tuning(struct mmc *mmc) -{
> - struct mmc_cmd cmd;
> -
> - cmd.cmdidx = MMC_CMD_STOP_TRANSMISSION;
> - cmd.cmdarg = 0;
> - cmd.resp_type = MMC_RSP_R1b;
> -
> - dm_mmc_send_cmd(mmc->dev, &cmd, NULL);
> -}
> -
> -static int fsl_esdhc_execute_tuning(struct udevice *dev, uint32_t opcode) -{
> - struct fsl_esdhc_plat *plat = dev_get_platdata(dev);
> - struct fsl_esdhc_priv *priv = dev_get_priv(dev);
> - struct fsl_esdhc *regs = priv->esdhc_regs;
> - struct mmc *mmc = &plat->mmc;
> - u32 irqstaten = readl(®s->irqstaten);
> - u32 irqsigen = readl(®s->irqsigen);
> - int i, ret = -ETIMEDOUT;
> - u32 val, mixctrl;
> -
> - /* clock tuning is not needed for upto 52MHz */
> - if (mmc->clock <= 52000000)
> - return 0;
> -
> - /* This is readw/writew SDHCI_HOST_CONTROL2 when tuning */
> - if (priv->flags & ESDHC_FLAG_STD_TUNING) {
> - val = readl(®s->autoc12err);
> - mixctrl = readl(®s->mixctrl);
> - val &= ~MIX_CTRL_SMPCLK_SEL;
> - mixctrl &= ~(MIX_CTRL_FBCLK_SEL | MIX_CTRL_AUTO_TUNE_EN);
> -
> - val |= MIX_CTRL_EXE_TUNE;
> - mixctrl |= MIX_CTRL_FBCLK_SEL | MIX_CTRL_AUTO_TUNE_EN;
> -
> - writel(val, ®s->autoc12err);
> - writel(mixctrl, ®s->mixctrl);
> - }
> -
> - /* sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE);
> */
> - mixctrl = readl(®s->mixctrl);
> - mixctrl = MIX_CTRL_DTDSEL_READ | (mixctrl &
> ~MIX_CTRL_SDHCI_MASK);
> - writel(mixctrl, ®s->mixctrl);
> -
> - writel(IRQSTATEN_BRR, ®s->irqstaten);
> - writel(IRQSTATEN_BRR, ®s->irqsigen);
> -
> - /*
> - * Issue opcode repeatedly till Execute Tuning is set to 0 or the number
> - * of loops reaches 40 times.
> - */
> - for (i = 0; i < MAX_TUNING_LOOP; i++) {
> - u32 ctrl;
> -
> - if (opcode == MMC_CMD_SEND_TUNING_BLOCK_HS200) {
> - if (mmc->bus_width == 8)
> - writel(0x7080, ®s->blkattr);
> - else if (mmc->bus_width == 4)
> - writel(0x7040, ®s->blkattr);
> - } else {
> - writel(0x7040, ®s->blkattr);
> - }
> -
> - /* sdhci_writew(host, SDHCI_TRNS_READ,
> SDHCI_TRANSFER_MODE) */
> - val = readl(®s->mixctrl);
> - val = MIX_CTRL_DTDSEL_READ | (val & ~MIX_CTRL_SDHCI_MASK);
> - writel(val, ®s->mixctrl);
> -
> - /* We are using STD tuning, no need to check return value */
> - mmc_send_tuning(mmc, opcode, NULL);
> -
> - ctrl = readl(®s->autoc12err);
> - if ((!(ctrl & MIX_CTRL_EXE_TUNE)) &&
> - (ctrl & MIX_CTRL_SMPCLK_SEL)) {
> - /*
> - * need to wait some time, make sure sd/mmc fininsh
> - * send out tuning data, otherwise, the sd/mmc can't
> - * response to any command when the card still out
> - * put the tuning data.
> - */
> - mdelay(1);
> - ret = 0;
> - break;
> - }
> -
> - /* Add 1ms delay for SD and eMMC */
> - mdelay(1);
> - }
> -
> - writel(irqstaten, ®s->irqstaten);
> - writel(irqsigen, ®s->irqsigen);
> -
> - esdhc_stop_tuning(mmc);
> -
> - return ret;
> -}
> -#endif
> -
> static int esdhc_set_ios_common(struct fsl_esdhc_priv *priv, struct mmc
> *mmc) {
> struct fsl_esdhc *regs = priv->esdhc_regs;
> - int ret __maybe_unused;
>
> #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
> /* Select to use peripheral clock */
> esdhc_clock_control(priv, false);
> - esdhc_setbits32(®s->scr, ESDHCCTL_PCS);
> + esdhc_setbits32(®s->esdhcctl, ESDHCCTL_PCS);
> esdhc_clock_control(priv, true);
> #endif
> /* Set the clock speed */
> if (priv->clock != mmc->clock)
> set_sysctl(priv, mmc, mmc->clock);
>
> -#ifdef MMC_SUPPORTS_TUNING
> - if (mmc->clk_disable) {
> -#ifdef CONFIG_FSL_USDHC
> - esdhc_clrbits32(®s->vendorspec, VENDORSPEC_CKEN);
> -#else
> - esdhc_clrbits32(®s->sysctl, SYSCTL_CKEN);
> -#endif
> - } else {
> -#ifdef CONFIG_FSL_USDHC
> - esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN |
> - VENDORSPEC_CKEN);
> -#else
> - esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_CKEN);
> -#endif
> - }
> -
> - if (priv->mode != mmc->selected_mode) {
> - ret = esdhc_set_timing(mmc);
> - if (ret) {
> - printf("esdhc_set_timing error %d\n", ret);
> - return ret;
> - }
> - }
> -
> - if (priv->signal_voltage != mmc->signal_voltage) {
> - ret = esdhc_set_voltage(mmc);
> - if (ret) {
> - printf("esdhc_set_voltage error %d\n", ret);
> - return ret;
> - }
> - }
> -#endif
> -
> /* Set the bus width */
> esdhc_clrbits32(®s->proctl, PROCTL_DTW_4 | PROCTL_DTW_8);
>
> @@ -1037,34 +629,10 @@ static int esdhc_init_common(struct
> fsl_esdhc_priv *priv, struct mmc *mmc)
> return -ETIMEDOUT;
> }
>
> -#if defined(CONFIG_FSL_USDHC)
> - /* RSTA doesn't reset MMC_BOOT register, so manually reset it */
> - esdhc_write32(®s->mmcboot, 0x0);
> - /* Reset MIX_CTRL and CLK_TUNE_CTRL_STATUS regs to 0 */
> - esdhc_write32(®s->mixctrl, 0x0);
> - esdhc_write32(®s->clktunectrlstatus, 0x0);
> -
> - /* Put VEND_SPEC to default value */
> - if (priv->vs18_enable)
> - esdhc_write32(®s->vendorspec, (VENDORSPEC_INIT |
> - ESDHC_VENDORSPEC_VSELECT));
> - else
> - esdhc_write32(®s->vendorspec, VENDORSPEC_INIT);
> -
> - /* Disable DLL_CTRL delay line */
> - esdhc_write32(®s->dllctrl, 0x0);
> -#endif
> -
> -#ifndef ARCH_MXC
> /* Enable cache snooping */
> - esdhc_write32(®s->scr, 0x00000040);
> -#endif
> + esdhc_write32(®s->esdhcctl, 0x00000040);
>
> -#ifndef CONFIG_FSL_USDHC
> esdhc_setbits32(®s->sysctl, SYSCTL_HCKEN | SYSCTL_IPGEN); -#else
> - esdhc_setbits32(®s->vendorspec, VENDORSPEC_HCKEN |
> VENDORSPEC_IPGEN);
> -#endif
>
> /* Set the initial clock speed */
> mmc_set_clock(mmc, 400000, MMC_CLK_ENABLE); @@ -1098,10
> +666,6 @@ static int esdhc_getcd_common(struct fsl_esdhc_priv *priv) #if
> CONFIG_IS_ENABLED(DM_MMC)
> if (priv->non_removable)
> return 1;
> -#ifdef CONFIG_DM_GPIO
> - if (dm_gpio_is_valid(&priv->cd_gpio))
> - return dm_gpio_get_value(&priv->cd_gpio);
> -#endif
> #endif
>
> while (!(esdhc_read32(®s->prsstat) & PRSSTAT_CINS) && --timeout)
> @@ -1190,20 +754,8 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
> esdhc_write32(®s->proctl, PROCTL_INIT | PROCTL_D3CD); #endif
>
> -#ifndef CONFIG_FSL_USDHC
> - esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN
> - | SYSCTL_IPGEN | SYSCTL_CKEN);
> - /* Clearing tuning bits in case ROM has set it already */
> - esdhc_write32(®s->mixctrl, 0);
> - esdhc_write32(®s->autoc12err, 0);
> - esdhc_write32(®s->clktunectrlstatus, 0);
> -#else
> - esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN |
> - VENDORSPEC_HCKEN | VENDORSPEC_IPGEN |
> VENDORSPEC_CKEN);
> -#endif
> -
> - if (priv->vs18_enable)
> - esdhc_setbits32(®s->vendorspec,
> ESDHC_VENDORSPEC_VSELECT);
> + esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN |
> + SYSCTL_IPGEN | SYSCTL_CKEN);
>
> writel(SDHCI_IRQ_EN_BITS, ®s->irqstaten);
> cfg = &plat->cfg;
> @@ -1279,27 +831,11 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv
> *priv,
> cfg->host_caps &= ~MMC_MODE_8BIT;
> #endif
>
> - cfg->host_caps |= priv->caps;
> -
> cfg->f_min = 400000;
> cfg->f_max = min(priv->sdhc_clk, (u32)200000000);
>
> cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
>
> - writel(0, ®s->dllctrl);
> - if (priv->flags & ESDHC_FLAG_USDHC) {
> - if (priv->flags & ESDHC_FLAG_STD_TUNING) {
> - u32 val = readl(®s->tuning_ctrl);
> -
> - val |= ESDHC_STD_TUNING_EN;
> - val &= ~ESDHC_TUNING_START_TAP_MASK;
> - val |= priv->tuning_start_tap;
> - val &= ~ESDHC_TUNING_STEP_MASK;
> - val |= (priv->tuning_step) << ESDHC_TUNING_STEP_SHIFT;
> - writel(val, ®s->tuning_ctrl);
> - }
> - }
> -
> return 0;
> }
>
> @@ -1314,7 +850,6 @@ static int fsl_esdhc_cfg_to_priv(struct fsl_esdhc_cfg
> *cfg,
> priv->bus_width = cfg->max_bus_width;
> priv->sdhc_clk = cfg->sdhc_clk;
> priv->wp_enable = cfg->wp_enable;
> - priv->vs18_enable = cfg->vs18_enable;
>
> return 0;
> };
> @@ -1449,22 +984,11 @@ void fdt_fixup_esdhc(void *blob, bd_t *bd)
>
> #if CONFIG_IS_ENABLED(DM_MMC)
> #include <asm/arch/clock.h>
> -__weak void init_clk_usdhc(u32 index)
> -{
> -}
> -
> static int fsl_esdhc_probe(struct udevice *dev) {
> struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
> struct fsl_esdhc_plat *plat = dev_get_platdata(dev);
> struct fsl_esdhc_priv *priv = dev_get_priv(dev);
> - const void *fdt = gd->fdt_blob;
> - int node = dev_of_offset(dev);
> - struct esdhc_soc_data *data =
> - (struct esdhc_soc_data *)dev_get_driver_data(dev);
> -#if CONFIG_IS_ENABLED(DM_REGULATOR)
> - struct udevice *vqmmc_dev;
> -#endif
> fdt_addr_t addr;
> unsigned int val;
> struct mmc *mmc;
> @@ -1476,11 +1000,6 @@ static int fsl_esdhc_probe(struct udevice *dev)
>
> priv->esdhc_regs = (struct fsl_esdhc *)addr;
> priv->dev = dev;
> - priv->mode = -1;
> - if (data) {
> - priv->flags = data->flags;
> - priv->caps = data->caps;
> - }
>
> val = dev_read_u32_default(dev, "bus-width", -1);
> if (val == 8)
> @@ -1490,81 +1009,13 @@ static int fsl_esdhc_probe(struct udevice *dev)
> else
> priv->bus_width = 1;
>
> - val = fdtdec_get_int(fdt, node, "fsl,tuning-step", 1);
> - priv->tuning_step = val;
> - val = fdtdec_get_int(fdt, node, "fsl,tuning-start-tap",
> - ESDHC_TUNING_START_TAP_DEFAULT);
> - priv->tuning_start_tap = val;
> - val = fdtdec_get_int(fdt, node, "fsl,strobe-dll-delay-target",
> -
> ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT);
> - priv->strobe_dll_delay_target = val;
> -
> if (dev_read_bool(dev, "non-removable")) {
> priv->non_removable = 1;
> } else {
> priv->non_removable = 0;
> -#ifdef CONFIG_DM_GPIO
> - gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio,
> - GPIOD_IS_IN);
> -#endif
> }
>
> - if (dev_read_prop(dev, "fsl,wp-controller", NULL)) {
> - priv->wp_enable = 1;
> - } else {
> - priv->wp_enable = 0;
> -#ifdef CONFIG_DM_GPIO
> - gpio_request_by_name(dev, "wp-gpios", 0, &priv->wp_gpio,
> - GPIOD_IS_IN);
> -#endif
> - }
> -
> - priv->vs18_enable = 0;
> -
> -#if CONFIG_IS_ENABLED(DM_REGULATOR)
> - /*
> - * If emmc I/O has a fixed voltage at 1.8V, this must be provided,
> - * otherwise, emmc will work abnormally.
> - */
> - ret = device_get_supply_regulator(dev, "vqmmc-supply", &vqmmc_dev);
> - if (ret) {
> - dev_dbg(dev, "no vqmmc-supply\n");
> - } else {
> - ret = regulator_set_enable(vqmmc_dev, true);
> - if (ret) {
> - dev_err(dev, "fail to enable vqmmc-supply\n");
> - return ret;
> - }
> -
> - if (regulator_get_value(vqmmc_dev) == 1800000)
> - priv->vs18_enable = 1;
> - }
> -#endif
> -
> - if (fdt_get_property(fdt, node, "no-1-8-v", NULL))
> - priv->caps &= ~(UHS_CAPS | MMC_MODE_HS200 |
> MMC_MODE_HS400);
> -
> - /*
> - * TODO:
> - * Because lack of clk driver, if SDHC clk is not enabled,
> - * need to enable it first before this driver is invoked.
> - *
> - * we use MXC_ESDHC_CLK to get clk freq.
> - * If one would like to make this function work,
> - * the aliases should be provided in dts as this:
> - *
> - * aliases {
> - * mmc0 = &usdhc1;
> - * mmc1 = &usdhc2;
> - * mmc2 = &usdhc3;
> - * mmc3 = &usdhc4;
> - * };
> - * Then if your board only supports mmc2 and mmc3, but we can
> - * correctly get the seq as 2 and 3, then let mxc_get_clock
> - * work as expected.
> - */
> -
> - init_clk_usdhc(dev->seq);
> + priv->wp_enable = 1;
>
> if (IS_ENABLED(CONFIG_CLK)) {
> /* Assigned clock already set clock */ @@ -1631,28 +1082,10 @@
> static const struct dm_mmc_ops fsl_esdhc_ops = {
> .get_cd = fsl_esdhc_get_cd,
> .send_cmd = fsl_esdhc_send_cmd,
> .set_ios = fsl_esdhc_set_ios,
> -#ifdef MMC_SUPPORTS_TUNING
> - .execute_tuning = fsl_esdhc_execute_tuning,
> -#endif
> };
> #endif
>
> -static struct esdhc_soc_data usdhc_imx7d_data = {
> - .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
> - | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
> - | ESDHC_FLAG_HS400,
> - .caps = UHS_CAPS | MMC_MODE_HS200 | MMC_MODE_DDR_52MHz |
> - MMC_MODE_HS_52MHz | MMC_MODE_HS,
> -};
> -
> static const struct udevice_id fsl_esdhc_ids[] = {
> - { .compatible = "fsl,imx53-esdhc", },
> - { .compatible = "fsl,imx6ul-usdhc", },
> - { .compatible = "fsl,imx6sx-usdhc", },
> - { .compatible = "fsl,imx6sl-usdhc", },
> - { .compatible = "fsl,imx6q-usdhc", },
> - { .compatible = "fsl,imx7d-usdhc", .data = (ulong)&usdhc_imx7d_data,},
> - { .compatible = "fsl,imx7ulp-usdhc", },
> { .compatible = "fsl,esdhc", },
> { /* sentinel */ }
> };
> diff --git a/include/fsl_esdhc.h b/include/fsl_esdhc.h index
> 8dbd5249a7..7d7e946ab3 100644
> --- a/include/fsl_esdhc.h
> +++ b/include/fsl_esdhc.h
> @@ -9,7 +9,6 @@
> #ifndef __FSL_ESDHC_H__
> #define __FSL_ESDHC_H__
>
> -#include <linux/bitops.h>
> #include <linux/errno.h>
> #include <asm/byteorder.h>
>
> @@ -25,22 +24,14 @@
> #define SYSCTL_INITA 0x08000000
> #define SYSCTL_TIMEOUT_MASK 0x000f0000
> #define SYSCTL_CLOCK_MASK 0x0000fff0
> -#if !defined(CONFIG_FSL_USDHC)
> #define SYSCTL_CKEN 0x00000008
> #define SYSCTL_PEREN 0x00000004
> #define SYSCTL_HCKEN 0x00000002
> #define SYSCTL_IPGEN 0x00000001
> -#endif
> #define SYSCTL_RSTA 0x01000000
> #define SYSCTL_RSTC 0x02000000
> #define SYSCTL_RSTD 0x04000000
>
> -#define VENDORSPEC_CKEN 0x00004000
> -#define VENDORSPEC_PEREN 0x00002000
> -#define VENDORSPEC_HCKEN 0x00001000
> -#define VENDORSPEC_IPGEN 0x00000800
> -#define VENDORSPEC_INIT 0x20007809
> -
> #define IRQSTAT 0x0002e030
> #define IRQSTAT_DMAE (0x10000000)
> #define IRQSTAT_AC12E (0x01000000)
> @@ -172,54 +163,6 @@
> #define ESDHC_HOSTCAPBLT_DMAS 0x00400000
> #define ESDHC_HOSTCAPBLT_HSS 0x00200000
>
> -#define ESDHC_VENDORSPEC_VSELECT 0x00000002 /* Use 1.8V */
> -
> -/* Imported from Linux Kernel drivers/mmc/host/sdhci-esdhc-imx.c */
> -#define MIX_CTRL_DDREN BIT(3)
> -#define MIX_CTRL_DTDSEL_READ BIT(4)
> -#define MIX_CTRL_AC23EN BIT(7)
> -#define MIX_CTRL_EXE_TUNE BIT(22)
> -#define MIX_CTRL_SMPCLK_SEL BIT(23)
> -#define MIX_CTRL_AUTO_TUNE_EN BIT(24)
> -#define MIX_CTRL_FBCLK_SEL BIT(25)
> -#define MIX_CTRL_HS400_EN BIT(26)
> -#define MIX_CTRL_HS400_ES BIT(27)
> -/* Bits 3 and 6 are not SDHCI standard definitions */
> -#define MIX_CTRL_SDHCI_MASK 0xb7
> -/* Tuning bits */
> -#define MIX_CTRL_TUNING_MASK 0x03c00000
> -
> -/* strobe dll register */
> -#define ESDHC_STROBE_DLL_CTRL 0x70
> -#define ESDHC_STROBE_DLL_CTRL_ENABLE BIT(0)
> -#define ESDHC_STROBE_DLL_CTRL_RESET BIT(1)
> -#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT 0x7
> -#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT 3
> -
> -#define ESDHC_STROBE_DLL_STATUS 0x74
> -#define ESDHC_STROBE_DLL_STS_REF_LOCK BIT(1)
> -#define ESDHC_STROBE_DLL_STS_SLV_LOCK 0x1
> -#define ESDHC_STROBE_DLL_CLK_FREQ 100000000
> -
> -#define ESDHC_STD_TUNING_EN BIT(24)
> -/* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
> -#define ESDHC_TUNING_START_TAP_DEFAULT 0x1
> -#define ESDHC_TUNING_START_TAP_MASK 0xff
> -#define ESDHC_TUNING_STEP_MASK 0x00070000
> -#define ESDHC_TUNING_STEP_SHIFT 16
> -
> -#define ESDHC_FLAG_MULTIBLK_NO_INT BIT(1)
> -#define ESDHC_FLAG_ENGCM07207 BIT(2)
> -#define ESDHC_FLAG_USDHC BIT(3)
> -#define ESDHC_FLAG_MAN_TUNING BIT(4)
> -#define ESDHC_FLAG_STD_TUNING BIT(5)
> -#define ESDHC_FLAG_HAVE_CAP1 BIT(6)
> -#define ESDHC_FLAG_ERR004536 BIT(7)
> -#define ESDHC_FLAG_HS200 BIT(8)
> -#define ESDHC_FLAG_HS400 BIT(9)
> -#define ESDHC_FLAG_ERR010450 BIT(10)
> -#define ESDHC_FLAG_HS400_ES BIT(11)
> -
> struct fsl_esdhc_cfg {
> phys_addr_t esdhc_base;
> u32 sdhc_clk;
Acked-by: Peng Fan <peng....@nxp.com>
> --
> 2.17.1
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
