> When CONFIG_CLK enabled, use CLK UCLASS for clk related settings.
> 
> Signed-off-by: Peng Fan <peng....@nxp.com>
> ---
>  arch/arm/include/asm/mach-imx/mxc_i2c.h |  6 ++++++
>  drivers/i2c/mxc_i2c.c                   | 17 +++++++++++++++++
>  2 files changed, 23 insertions(+)
> 
> diff --git a/arch/arm/include/asm/mach-imx/mxc_i2c.h 
> b/arch/arm/include/asm/mach-imx/mxc_i2c.h
> index 8e1ea9af19..81fd981444 100644
> --- a/arch/arm/include/asm/mach-imx/mxc_i2c.h
> +++ b/arch/arm/include/asm/mach-imx/mxc_i2c.h
> @@ -6,6 +6,9 @@
>  #define __ASM_ARCH_MXC_MXC_I2C_H__
>  #include <asm-generic/gpio.h>
>  #include <asm/mach-imx/iomux-v3.h>
> +#if CONFIG_IS_ENABLED(CLK)
> +#include <clk.h>
> +#endif
>  
>  struct i2c_pin_ctrl {
>       iomux_v3_cfg_t i2c_mode;
> @@ -47,6 +50,9 @@ struct mxc_i2c_bus {
>       ulong driver_data;
>       int speed;
>       struct i2c_pads_info *pads_info;
> +#if CONFIG_IS_ENABLED(CLK)
> +     struct clk per_clk;
> +#endif
>  #ifndef CONFIG_DM_I2C
>       int (*idle_bus_fn)(void *p);
>       void *idle_bus_data;
> diff --git a/drivers/i2c/mxc_i2c.c b/drivers/i2c/mxc_i2c.c
> index 23119cce65..2e157bca58 100644
> --- a/drivers/i2c/mxc_i2c.c
> +++ b/drivers/i2c/mxc_i2c.c
> @@ -890,9 +890,22 @@ static int mxc_i2c_probe(struct udevice *bus)
>       i2c_bus->bus = bus;
>  
>       /* Enable clk */
> +#if CONFIG_IS_ENABLED(CLK)
> +     ret = clk_get_by_index(bus, 0, &i2c_bus->per_clk);
> +     if (ret) {
> +             printf("Failed to get i2c clk\n");
> +             return ret;
> +     }
> +     ret = clk_enable(&i2c_bus->per_clk);
> +     if (ret) {
> +             printf("Failed to enable i2c clk\n");
> +             return ret;
> +     }
> +#else
>       ret = enable_i2c_clk(1, bus->seq);
>       if (ret < 0)
>               return ret;
> +#endif
>  
>       /*
>        * See Documentation/devicetree/bindings/i2c/i2c-imx.txt
> @@ -919,7 +932,11 @@ static int mxc_i2c_probe(struct udevice *bus)
>       ret = i2c_idle_bus(i2c_bus);
>       if (ret < 0) {
>               /* Disable clk */
> +#if CONFIG_IS_ENABLED(CLK)
> +             clk_disable(&i2c_bus->per_clk);
> +#else
>               enable_i2c_clk(0, bus->seq);
> +#endif
>               return ret;
>       }
Reviewed-by: Ye Li <ye...@nxp.com>

Best regards,
Ye Li

>  
> 

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot

Reply via email to