* the following problems are met : config was set to use the new driver as a default but - RMII was not enabled for the new driver - the new driver didn't compile with RMII enabled - the new driver initialize a PHY at address O when the PHY of this board is at 1 thus we get "AT91 EMAC RMII: No PHY present"
* to fix these problems, this patch : - enable RMII for the new driver - fix the wrong define used in the at91_emac.c - allow the config file to set a default phy address (and use 0 as a default as in the actual at91_emac.c driver) Signed-off-by: Eric Bénard <e...@eukrea.com> --- v2 : fix line lengths drivers/net/at91_emac.c | 32 ++++++++++++++++++++++---------- include/configs/cpuat91.h | 9 +++------ 2 files changed, 25 insertions(+), 16 deletions(-) diff --git a/drivers/net/at91_emac.c b/drivers/net/at91_emac.c index 2399569..cf0a7c0 100644 --- a/drivers/net/at91_emac.c +++ b/drivers/net/at91_emac.c @@ -53,6 +53,10 @@ Please decrease the CONFIG_SYS_RX_ETH_BUFFER value #endif +#ifndef CONFIG_DRIVER_AT91EMAC_PHYADDR +#define CONFIG_DRIVER_AT91EMAC_PHYADDR 0 +#endif + /* MDIO clock must not exceed 2.5 MHz, so enable MCK divider */ #if (AT91C_MASTER_CLOCK > 80000000) #define HCLK_DIV AT91_EMAC_CFG_MCLK_64 @@ -198,12 +202,15 @@ static int at91emac_phy_reset(struct eth_device *netdev) emac = (at91_emac_t *) netdev->iobase; adv = ADVERTISE_CSMA | ADVERTISE_ALL; - at91emac_write(emac, 0, MII_ADVERTISE, adv); + at91emac_write(emac, CONFIG_DRIVER_AT91EMAC_PHYADDR, + MII_ADVERTISE, adv); VERBOSEP("%s: Starting autonegotiation...\n", netdev->name); - at91emac_write(emac, 0, MII_BMCR, (BMCR_ANENABLE | BMCR_ANRESTART)); + at91emac_write(emac, CONFIG_DRIVER_AT91EMAC_PHYADDR, MII_BMCR, + (BMCR_ANENABLE | BMCR_ANRESTART)); for (i = 0; i < 100000 / 100; i++) { - at91emac_read(emac, 0, MII_BMSR, &status); + at91emac_read(emac, CONFIG_DRIVER_AT91EMAC_PHYADDR, + MII_BMSR, &status); if (status & BMSR_ANEGCOMPLETE) break; udelay(100); @@ -229,13 +236,15 @@ static int at91emac_phy_init(struct eth_device *netdev) emac = (at91_emac_t *) netdev->iobase; /* Check if the PHY is up to snuff... */ - at91emac_read(emac, 0, MII_PHYSID1, &phy_id); + at91emac_read(emac, CONFIG_DRIVER_AT91EMAC_PHYADDR, + MII_PHYSID1, &phy_id); if (phy_id == 0xffff) { printf("%s: No PHY present\n", netdev->name); return 1; } - at91emac_read(emac, 0, MII_BMSR, &status); + at91emac_read(emac, CONFIG_DRIVER_AT91EMAC_PHYADDR, + MII_BMSR, &status); if (!(status & BMSR_LSTATUS)) { /* Try to re-negotiate if we don't have link already. */ @@ -243,7 +252,8 @@ static int at91emac_phy_init(struct eth_device *netdev) return 2; for (i = 0; i < 100000 / 100; i++) { - at91emac_read(emac, 0, MII_BMSR, &status); + at91emac_read(emac, CONFIG_DRIVER_AT91EMAC_PHYADDR, + MII_BMSR, &status); if (status & BMSR_LSTATUS) break; udelay(100); @@ -253,8 +263,10 @@ static int at91emac_phy_init(struct eth_device *netdev) VERBOSEP("%s: link down\n", netdev->name); return 3; } else { - at91emac_read(emac, 0, MII_ADVERTISE, &adv); - at91emac_read(emac, 0, MII_LPA, &lpa); + at91emac_read(emac, CONFIG_DRIVER_AT91EMAC_PHYADDR, + MII_ADVERTISE, &adv); + at91emac_read(emac, CONFIG_DRIVER_AT91EMAC_PHYADDR, + MII_LPA, &lpa); media = mii_nway_result(lpa & adv); speed = (media & (ADVERTISE_100FULL | ADVERTISE_100HALF) ? 1 : 0); @@ -271,7 +283,7 @@ int at91emac_UpdateLinkSpeed(at91_emac_t *emac) { unsigned short stat1; - at91emac_read(emac, 0, MII_BMSR, &stat1); + at91emac_read(emac, CONFIG_DRIVER_AT91EMAC_PHYADDR, MII_BMSR, &stat1); if (!(stat1 & BMSR_LSTATUS)) /* link status up? */ return 1; @@ -372,7 +384,7 @@ static int at91emac_init(struct eth_device *netdev, bd_t *bd) value = AT91_EMAC_CFG_CAF | AT91_EMAC_CFG_NBC | HCLK_DIV; #ifdef CONFIG_RMII - value |= AT91C_EMAC_RMII; + value |= AT91_EMAC_CFG_RMII; #endif writel(value, &emac->cfg); diff --git a/include/configs/cpuat91.h b/include/configs/cpuat91.h index b4fda76..049298c 100644 --- a/include/configs/cpuat91.h +++ b/include/configs/cpuat91.h @@ -131,15 +131,12 @@ (CONFIG_SYS_MEMTEST_START + PHYS_SDRAM_SIZE - 512 * 1024) #define CONFIG_NET_MULTI 1 -#ifdef CONFIG_NET_MULTI #define CONFIG_DRIVER_AT91EMAC 1 #define CONFIG_SYS_RX_ETH_BUFFER 8 -#else -#define CONFIG_DRIVER_ETHER 1 -#endif +#define CONFIG_RMII 1 +#define CONFIG_MII 1 +#define CONFIG_DRIVER_AT91EMAC_PHYADDR 1 #define CONFIG_NET_RETRY_COUNT 20 -#define CONFIG_AT91C_USE_RMII 1 -#define CONFIG_PHY_ADDRESS (1 << 5) #define CONFIG_KS8721_PHY 1 #define CONFIG_SYS_FLASH_CFI 1 -- 1.6.3.3 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot