Sync Kernel DTS for Allwinner H6 boards.
Drop /omit-if-no-ref/ keyword as it's not supported by U-boot.
commit <d45331b00ddb> Linux 5.3-rc4
Signed-off-by: Clément Péron <peron.c...@gmail.com>
---
arch/arm/dts/sun50i-h6-beelink-gs1.dts | 76 ++++++++++++++++++++++++++
arch/arm/dts/sun50i-h6-pine-h64.dts | 12 ++++
arch/arm/dts/sun50i-h6.dtsi | 46 +++++++++++++++-
3 files changed, 131 insertions(+), 3 deletions(-)
diff --git a/arch/arm/dts/sun50i-h6-beelink-gs1.dts
b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
index 54b0882bed..0dc33c90dd 100644
--- a/arch/arm/dts/sun50i-h6-beelink-gs1.dts
+++ b/arch/arm/dts/sun50i-h6-beelink-gs1.dts
@@ -14,6 +14,7 @@
compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
@@ -21,6 +22,17 @@
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
@@ -41,6 +53,40 @@
};
};
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ext_rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <®_aldo2>;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&mmc0 {
vmmc-supply = <®_cldo1>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
@@ -57,6 +103,15 @@
status = "okay";
};
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ vcc-pd-supply = <®_cldo1>;
+ vcc-pg-supply = <®_aldo1>;
+};
+
&r_i2c {
status = "okay";
@@ -177,8 +232,29 @@
};
};
+&r_pio {
+ /*
+ * PL0 and PL1 are used for PMIC I2C
+ * don't enable the pl-supply else
+ * it will fail at boot
+ *
+ * vcc-pl-supply = <®_aldo1>;
+ */
+ vcc-pm-supply = <®_aldo1>;
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_ph_pins>;
status = "okay";
};
+
+&usb2otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb2phy {
+ usb0_vbus-supply = <®_vcc5v>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun50i-h6-pine-h64.dts
b/arch/arm/dts/sun50i-h6-pine-h64.dts
index 4802902e12..1898345183 100644
--- a/arch/arm/dts/sun50i-h6-pine-h64.dts
+++ b/arch/arm/dts/sun50i-h6-pine-h64.dts
@@ -127,6 +127,12 @@
status = "okay";
};
+&pio {
+ vcc-pc-supply = <®_bldo2>;
+ vcc-pd-supply = <®_cldo1>;
+ vcc-pg-supply = <®_aldo1>;
+};
+
&r_i2c {
status = "okay";
@@ -243,10 +249,16 @@
pcf8563: rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
#clock-cells = <0>;
};
};
+&r_pio {
+ vcc-pm-supply = <®_aldo1>;
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_ph_pins>;
diff --git a/arch/arm/dts/sun50i-h6.dtsi b/arch/arm/dts/sun50i-h6.dtsi
index e0dc4a05c1..a117f479ae 100644
--- a/arch/arm/dts/sun50i-h6.dtsi
+++ b/arch/arm/dts/sun50i-h6.dtsi
@@ -101,7 +101,7 @@
#size-cells = <1>;
ranges;
- display-engine@1000000 {
+ bus@1000000 {
compatible = "allwinner,sun50i-h6-de3",
"allwinner,sun50i-a64-de2";
reg = <0x1000000 0x400000>;
@@ -203,11 +203,32 @@
#reset-cells = <1>;
};
+ dma: dma-controller@3002000 {
+ compatible = "allwinner,sun50i-h6-dma";
+ reg = <0x03002000 0x1000>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>;
+ clock-names = "bus", "mbus";
+ dma-channels = <16>;
+ dma-requests = <46>;
+ resets = <&ccu RST_BUS_DMA>;
+ #dma-cells = <1>;
+ };
+
sid: sid@3006000 {
compatible = "allwinner,sun50i-h6-sid";
reg = <0x03006000 0x400>;
};
+ watchdog: watchdog@30090a0 {
+ compatible = "allwinner,sun50i-h6-wdt",
+ "allwinner,sun6i-a31-wdt";
+ reg = <0x030090a0 0x20>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ /* Broken on some H6 boards */
+ status = "disabled";
+ };
+
pio: pinctrl@300b000 {
compatible = "allwinner,sun50i-h6-pinctrl";
reg = <0x0300b000 0x400>;
@@ -243,6 +264,18 @@
bias-pull-up;
};
+ /*
+ * /omit-if-no-ref/ isn't supported by U-boot
+ * keep this comment to avoid bad sync with Linux
+ */
+ mmc1_pins: mmc1-pins {
+ pins = "PG0", "PG1", "PG2", "PG3",
+ "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
mmc2_pins: mmc2-pins {
pins = "PC1", "PC4", "PC5", "PC6",
"PC7", "PC8", "PC9", "PC10",
@@ -294,6 +327,8 @@
resets = <&ccu RST_BUS_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -445,7 +480,6 @@
resets = <&ccu RST_BUS_OHCI3>,
<&ccu RST_BUS_EHCI3>;
phys = <&usb2phy 3>;
- phy-names = "usb";
status = "disabled";
};
@@ -457,7 +491,6 @@
<&ccu CLK_USB_OHCI3>;
resets = <&ccu RST_BUS_OHCI3>;
phys = <&usb2phy 3>;
- phy-names = "usb";
status = "disabled";
};
@@ -613,6 +646,13 @@
#reset-cells = <1>;
};
+ r_watchdog: watchdog@7020400 {
+ compatible = "allwinner,sun50i-h6-wdt",
+ "allwinner,sun6i-a31-wdt";
+ reg = <0x07020400 0x20>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
r_intc: interrupt-controller@7021000 {
compatible = "allwinner,sun50i-h6-r-intc",
"allwinner,sun6i-a31-r-intc";
--
2.20.1
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
