From: Matthias Brugger <mbrug...@suse.com>
U-Boot support on Raspberry Pi 4 relies on the device-tree
provided by the firmware. The blob does not contain the
U-Boot specific pre-loc-rel properties. The result is, that
the U-Boot banner is not printed.
We fix this by setting the DM_FLAG_PRE_RELOC flag in the driver,
if we rely on a device-tree provided by the firmware.
Signed-off-by: Matthias Brugger <mbrug...@suse.com>
---
Changes in v2:
- add DM_FLAG_PRE_RELOC for RPi4 case
drivers/pinctrl/broadcom/pinctrl-bcm283x.c | 2 +-
drivers/serial/serial_bcm283x_mu.c | 2 +-
drivers/serial/serial_bcm283x_pl011.c | 2 +-
3 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/pinctrl/broadcom/pinctrl-bcm283x.c
b/drivers/pinctrl/broadcom/pinctrl-bcm283x.c
index 3be080d29e..1bb91d6eed 100644
--- a/drivers/pinctrl/broadcom/pinctrl-bcm283x.c
+++ b/drivers/pinctrl/broadcom/pinctrl-bcm283x.c
@@ -148,7 +148,7 @@ U_BOOT_DRIVER(pinctrl_bcm283x) = {
.priv_auto_alloc_size = sizeof(struct bcm283x_pinctrl_priv),
.ops = &bcm283x_pinctrl_ops,
.probe = bcm283x_pinctl_probe,
-#if !CONFIG_IS_ENABLED(OF_CONTROL)
+#if !CONFIG_IS_ENABLED(OF_CONTROL) || CONFIG_IS_ENABLED(OF_BOARD)
.flags = DM_FLAG_PRE_RELOC,
#endif
};
diff --git a/drivers/serial/serial_bcm283x_mu.c
b/drivers/serial/serial_bcm283x_mu.c
index bd1d89ec83..a6ffc84b96 100644
--- a/drivers/serial/serial_bcm283x_mu.c
+++ b/drivers/serial/serial_bcm283x_mu.c
@@ -199,7 +199,7 @@ U_BOOT_DRIVER(serial_bcm283x_mu) = {
.platdata_auto_alloc_size = sizeof(struct bcm283x_mu_serial_platdata),
.probe = bcm283x_mu_serial_probe,
.ops = &bcm283x_mu_serial_ops,
-#if !CONFIG_IS_ENABLED(OF_CONTROL)
+#if !CONFIG_IS_ENABLED(OF_CONTROL) || CONFIG_IS_ENABLED(OF_BOARD)
.flags = DM_FLAG_PRE_RELOC,
#endif
.priv_auto_alloc_size = sizeof(struct bcm283x_mu_priv),
diff --git a/drivers/serial/serial_bcm283x_pl011.c
b/drivers/serial/serial_bcm283x_pl011.c
index 2527bb8b1c..7d8ab7b716 100644
--- a/drivers/serial/serial_bcm283x_pl011.c
+++ b/drivers/serial/serial_bcm283x_pl011.c
@@ -90,7 +90,7 @@ U_BOOT_DRIVER(bcm283x_pl011_uart) = {
.platdata_auto_alloc_size = sizeof(struct pl01x_serial_platdata),
.probe = pl01x_serial_probe,
.ops = &bcm283x_pl011_serial_ops,
-#if !CONFIG_IS_ENABLED(OF_CONTROL)
+#if !CONFIG_IS_ENABLED(OF_CONTROL) || CONFIG_IS_ENABLED(OF_BOARD)
.flags = DM_FLAG_PRE_RELOC,
#endif
.priv_auto_alloc_size = sizeof(struct pl01x_priv),
--
2.23.0
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
