On Mon, Dec 09, 2019 at 03:03:48PM +0000, Oliver Graute wrote: > On 06/12/19, Tom Rini wrote: > > On Fri, Dec 06, 2019 at 06:23:09PM +0100, Lukasz Majewski wrote: > > > Hi Igor, > > > > > > > Hi Stefano > > > > > > > > On Fri, Dec 6, 2019 at 6:24 PM Igor Opaniuk <igor.opan...@gmail.com> > > > > wrote: > > > > > > > > > > From: Igor Opaniuk <igor.opan...@toradex.com> > > > > > > > > > > Not all CONFIG_FSL_ESDHC defines were properly replaced with > > > > > CONFIG_FSL_ESDHC_IMX, which broke U-boot proper booting on > > > > > Colibri iMX6 SoMs. > > > > > > > > > > U-boot is stuck after this message: > > > > > Commercial temperature grade DDR3 timings, 64bit bus width. > > > > > Trying to boot from MMC1 > > > > > > > > > > Fixes: e37ac717d7("Convert to use fsl_esdhc_imx for i.MX platforms") > > > > > Signed-off-by: Igor Opaniuk <igor.opan...@toradex.com> > > > > > --- > > > > > > > > > > board/toradex/colibri_imx6/colibri_imx6.c | 4 ++-- > > > > > 1 file changed, 2 insertions(+), 2 deletions(-) > > > > > > > > > > diff --git a/board/toradex/colibri_imx6/colibri_imx6.c > > > > > b/board/toradex/colibri_imx6/colibri_imx6.c index > > > > > ad40b589c1..44173dde1f 100644 --- > > > > > a/board/toradex/colibri_imx6/colibri_imx6.c +++ > > > > > b/board/toradex/colibri_imx6/colibri_imx6.c @@ -83,7 +83,7 @@ > > > > > iomux_v3_cfg_t const uart1_pads[] = { > > > > > MX6_PAD_CSI0_DAT11__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), }; > > > > > > > > > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) > > > > > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) > > > > > /* Colibri MMC */ > > > > > iomux_v3_cfg_t const usdhc1_pads[] = { > > > > > MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), > > > > > @@ -304,7 +304,7 @@ int board_ehci_hcd_init(int port) > > > > > } > > > > > #endif > > > > > > > > > > -#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) > > > > > +#if defined(CONFIG_FSL_ESDHC_IMX) && defined(CONFIG_SPL_BUILD) > > > > > /* use the following sequence: eMMC, MMC */ > > > > > struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = { > > > > > {USDHC3_BASE_ADDR}, > > > > > -- > > > > > 2.17.1 > > > > > > > > > > > > > I've just found the same fix [1] but from Ricardo with Awaiting > > > > upstream status in patchwork (I thought that he has fixed just Apalis > > > > iMX6), but seems the patch was > > > > lost somewhere, as I can not find it nor in u-boot-imx/next neither > > > > in u-boot-imx/master branches. > > > > > > Thanks for providing the fix (at least for the Toradex boards) > > > > > > And I do guess that more i.MX6 boards are affected ... > > > > I think there's just one other. The imx8qm_rom7720_a1 references > > CONFIG_FSL_ESDHC still, but I don't see any other i.MX8 platforms doing > > anything with the symbol to compare with. > > thx for that hint, so I must replace CONFIG_FSL_ESDHC with > CONFIG_FSL_ESDHC_IMX in board/advantech/imx8qm_rom7720_a1/spl.c ?
Yes, and confirm that everything works as expected for the appropriate use cases. Thanks! -- Tom
signature.asc
Description: PGP signature