Hi Jerome,
Thanks for your review,
On Mon, 3 Feb 2020 at 21:11, Jerome Brunet <jbru...@baylibre.com> wrote:
>
>
> On Mon 03 Feb 2020 at 16:13, Anand Moon <linux.am...@gmail.com> wrote:
>
> > As per mainline line kernel fix the clk tuning phase for mmc,
> > set Core=180, Tx=180, Rx=0 clk phase for mmc initialization.
> > As per S905, S905X, AGX and S922X datasheet set the default
> > values for clk tuning.
> >
> > Signed-off-by: Anand Moon <linux.am...@gmail.com>
> > ---
> > arch/arm/include/asm/arch-meson/sd_emmc.h | 28 ++++++++++++------
> > drivers/mmc/meson_gx_mmc.c | 36 +++++++++++++++++++----
> > 2 files changed, 50 insertions(+), 14 deletions(-)
> >
> > diff --git a/arch/arm/include/asm/arch-meson/sd_emmc.h
> > b/arch/arm/include/asm/arch-meson/sd_emmc.h
> > index e3a72c8b66..b7a99947b3 100644
> > --- a/arch/arm/include/asm/arch-meson/sd_emmc.h
> > +++ b/arch/arm/include/asm/arch-meson/sd_emmc.h
> > @@ -7,6 +7,7 @@
> > #define __SD_EMMC_H__
> >
> > #include <mmc.h>
> > +#include <linux/bitops.h>
> >
> > #define SDIO_PORT_A 0
> > #define SDIO_PORT_B 1
> > @@ -19,15 +20,24 @@
> > #define CLK_MAX_DIV 63
> > #define CLK_SRC_24M (0 << 6)
> > #define CLK_SRC_DIV2 (1 << 6)
> > -#define CLK_CO_PHASE_000 (0 << 8)
> > -#define CLK_CO_PHASE_090 (1 << 8)
> > -#define CLK_CO_PHASE_180 (2 << 8)
> > -#define CLK_CO_PHASE_270 (3 << 8)
> > -#define CLK_TX_PHASE_000 (0 << 10)
> > -#define CLK_TX_PHASE_090 (1 << 10)
> > -#define CLK_TX_PHASE_180 (2 << 10)
> > -#define CLK_TX_PHASE_270 (3 << 10)
> > -#define CLK_ALWAYS_ON BIT(24)
> > +
> > +#define CRYSTAL_24MHZ 0
> > +#define CLK_PHASE_0 0
> > +#define CLK_PHASE_180 2
> > +
> > +#define CLK_DIV_MASK GENMASK(5, 0)
> > +#define CLK_SRC_MASK GENMASK(7, 6)
> > +#define CLK_CORE_PHASE_MASK GENMASK(9, 8)
> > +#define CLK_TX_PHASE_MASK GENMASK(11, 10)
> > +#define CLK_RX_PHASE_MASK GENMASK(13, 12)
> > +
> > +#define CLK_V2_TX_DELAY_MASK GENMASK(19, 16)
> > +#define CLK_V2_RX_DELAY_MASK GENMASK(23, 20)
> > +#define CLK_V2_ALWAYS_ON BIT(24)
> > +
> > +#define CLK_V3_TX_DELAY_MASK GENMASK(21, 16)
> > +#define CLK_V3_RX_DELAY_MASK GENMASK(27, 22)
> > +#define CLK_V3_ALWAYS_ON BIT(28)
> >
> > #define MESON_SD_EMMC_CFG 0x44
> > #define CFG_BUS_WIDTH_MASK GENMASK(1, 0)
> > diff --git a/drivers/mmc/meson_gx_mmc.c b/drivers/mmc/meson_gx_mmc.c
> > index 86c1a7164a..03fb70e717 100644
> > --- a/drivers/mmc/meson_gx_mmc.c
> > +++ b/drivers/mmc/meson_gx_mmc.c
> > @@ -16,6 +16,10 @@
> > #include <asm/arch/sd_emmc.h>
> > #include <linux/log2.h>
> >
> > +#include <linux/bitops.h>
> > +#include <linux/compat.h>
> > +#include <linux/bitfield.h>
> > +
> > static inline void *get_regbase(const struct mmc *mmc)
> > {
> > struct meson_mmc_platdata *pdata = mmc->priv;
> > @@ -51,11 +55,33 @@ static void meson_mmc_config_clock(struct mmc *mmc)
> > }
> > clk_div = DIV_ROUND_UP(clk, mmc->clock);
> >
> > - /* 180 phase core clock */
> > - meson_mmc_clk |= CLK_CO_PHASE_180;
> > -
> > - /* 180 phase tx clock */
> > - meson_mmc_clk |= CLK_TX_PHASE_000;
> > + /* Clock divider */
> > + meson_mmc_clk |= CLK_DIV_MASK;
> > + /* Clock source : Crystal 24MHz */
> > + meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);
> > + /* Core clock phase 2:180 */
> > + meson_mmc_clk |= FIELD_PREP(CLK_CORE_PHASE_MASK, CLK_PHASE_180);
> > + /* TX clock phase 2:180 */
> > + meson_mmc_clk |= FIELD_PREP(CLK_TX_PHASE_MASK, CLK_PHASE_180);
>
> I think I mentionned already but this is not aligned with the setting
> used by the linux driver. If you have problems with these, please report
> it to the linux mailing list
Yes I will try to send this changes to linux driver since these are
the recommend
default values as per the datasheets, see below.
Cfg_tx_phase: TX clock phase 0: 0 phase, 1: 90 phase, 2: 180 phase, 3:
270 phase. Recommended value: 2
>
> > + /* RX clock phase 0:180 */
> > + meson_mmc_clk |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);
> > +
> > +#ifdef CONFIG_MESON_GX
> > + /* TX clock delay line */
> > + meson_mmc_clk |= CLK_V2_TX_DELAY_MASK;
> > + /* RX clock delay line */
> > + meson_mmc_clk |= CLK_V2_RX_DELAY_MASK;
>
> Why do you need to this ?
As these are part of the linux driver, I added these,
I will check if this changes are needed in u-boot.
>
> > + /* clk always on */
> > + meson_mmc_clk |= CLK_V2_ALWAYS_ON;
> > +#endif
> > +#if (defined(CONFIG_MESON_AXG) || defined(CONFIG_MESON_G12A))
> > + /* TX clock delay line */
> > + meson_mmc_clk |= CLK_V3_TX_DELAY_MASK;
> > + /* RX clock delay line */
> > + meson_mmc_clk |= CLK_V3_RX_DELAY_MASK;
> > + /* clk always on */
> > + meson_mmc_clk |= CLK_V3_ALWAYS_ON;
> > +#endif
> >
> > /* clock settings */
> > meson_mmc_clk |= clk_src;
>
-Anand
