If enabled in config file and hwconfig, the memory test is performed after DDR initialization when U-boot stills runs in flash and cache. Whole memory is testable. It is mapped 2GB at a time using a sliding TLB window. After the testing, DDR is remapped with up to 2GB memory from the lowest address as normal.
Memory testing has different patterns which may be improved later. If memory test fails, DDR DIMM SPD and DDR controller registers are dumped. All zero values are omitted for better viewing. A worker function __setup_ddr_tlbs() is introduced to implement more control on physical address mapping. Signed-off-by: York Sun <york...@freescale.com> --- arch/powerpc/cpu/mpc85xx/cpu.c | 195 ++++++++++++++++++++++++++++++++++++++++ arch/powerpc/cpu/mpc85xx/tlb.c | 16 ++-- doc/README.fsl-ddr | 21 ++++- 3 files changed, 225 insertions(+), 7 deletions(-) diff --git a/arch/powerpc/cpu/mpc85xx/cpu.c b/arch/powerpc/cpu/mpc85xx/cpu.c index 00696f8..634a0cd 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu.c +++ b/arch/powerpc/cpu/mpc85xx/cpu.c @@ -34,6 +34,9 @@ #include <asm/io.h> #include <asm/mmu.h> #include <asm/fsl_law.h> +#include <post.h> +#include <asm/processor.h> +#include <asm/fsl_ddr_sdram.h> DECLARE_GLOBAL_DATA_PTR; @@ -282,3 +285,195 @@ void mpc85xx_reginfo(void) print_laws(); print_lbc_regs(); } + +#if CONFIG_POST & CONFIG_SYS_POST_MEMORY + +/* Board-specific functions defined in each board's ddr.c */ +void fsl_ddr_get_spd(generic_spd_eeprom_t *ctrl_dimms_spd, + unsigned int ctrl_num); +void read_tlbcam_entry(int idx, u32 *valid, u32 *tsize, unsigned long *epn, + phys_addr_t *rpn); +unsigned int __setup_ddr_tlbs(phys_addr_t p_addr, unsigned int memsize_in_meg); + +static void dump_spd_ddr_reg(void) +{ + int i, j, k, m; + u8 *p_8; + u32 *p_32; + ccsr_ddr_t *ddr[CONFIG_NUM_DDR_CONTROLLERS]; + generic_spd_eeprom_t + spd[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR]; + + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) + fsl_ddr_get_spd(spd[i], i); + puts("SPD data of all dimms (zero vaule is omitted)...\n"); + puts("Byte (hex) "); + k = 1; + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) + for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) + printf("Dimm%d ", k++); + puts("\n"); + for (k = 0; k < sizeof(generic_spd_eeprom_t); k++) { + m = 0; + printf("%3d (0x%02x) ", k, k); + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { + p_8 = (u8 *) &spd[i][j]; + if (p_8[k]) { + printf("0x%02x ", p_8[k]); + m++; + } else + puts(" "); + } + } + if (m) + puts("\n"); + else + puts("\r"); + } + + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + switch (i) { + case 0: + ddr[i] = (void *)CONFIG_SYS_MPC85xx_DDR_ADDR; + break; +#ifdef CONFIG_SYS_MPC85xx_DDR2_ADDR + case 1: + ddr[i] = (void *)CONFIG_SYS_MPC85xx_DDR2_ADDR; + break; +#endif + default: + printf("%s unexpected controller number = %u\n", + __func__, i); + return; + } + } + printf("DDR registers dump for all controllers " + "(zero vaule is omitted)...\n"); + puts("Offset (hex) "); + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) + printf(" Base + 0x%04x", (u32)ddr[i] & 0xFFFF); + puts("\n"); + for (k = 0; k < sizeof(ccsr_ddr_t)/4; k++) { + m = 0; + printf("%6d (0x%04x)", k * 4, k * 4); + for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { + p_32 = (u32 *) ddr[i]; + if (p_32[k]) { + printf(" 0x%08x", p_32[k]); + m++; + } else + puts(" "); + } + if (m) + puts("\n"); + else + puts("\r"); + } + puts("\n"); +} + +static int reset_tlb(phys_addr_t p_addr, u32 size, phys_addr_t *phys_offset) +{ + u32 vstart = CONFIG_SYS_DDR_SDRAM_BASE; + unsigned long epn; + u32 tsize, valid, ptr; + phys_addr_t rpn = 0; + int ddr_esel; + + ptr = vstart; + while (ptr < (vstart + size)) { + ddr_esel = find_tlb_idx((void *)ptr, 1); + if (ddr_esel != -1) { + read_tlbcam_entry(ddr_esel, &valid, &tsize, &epn, &rpn); + disable_tlb(ddr_esel); + } + ptr += TSIZE_TO_BYTES(tsize); + } + /* Setup new tlb to cover the physical address */ + __setup_ddr_tlbs(p_addr, size>>20); + + ptr = vstart; + ddr_esel = find_tlb_idx((void *)ptr, 1); + if (ddr_esel != -1) { + read_tlbcam_entry(ddr_esel, &valid, &tsize, &epn, phys_offset); + } else { + printf("TLB error in function %s\n", __func__); + return -1; + } + return 0; +} + +int arch_memory_test_advance(u32 *vstart, u32 *size, phys_addr_t *phys_offset) +{ + phys_addr_t test_cap, p_addr; + phys_size_t p_size = min(gd->ram_size, CONFIG_MAX_MEM_MAPPED); +#if !defined(CONFIG_PHYS_64BIT) || \ + !defined(CONFIG_SYS_INIT_RAM_ADDR_PHYS) || \ + (CONFIG_SYS_INIT_RAM_ADDR_PHYS < 0x100000000ull) + test_cap = p_size; +#else + test_cap = gd->ram_size; +#endif + p_addr = (*vstart) + (*size) + (*phys_offset); + if (p_addr < test_cap - 1) { + p_size = min(test_cap - p_addr, CONFIG_MAX_MEM_MAPPED); + if (reset_tlb(p_addr, p_size, phys_offset) == -1) + return -1; + *vstart = CONFIG_SYS_DDR_SDRAM_BASE; + *size = (u32) p_size; + printf("Testing 0x%08llx - 0x%08llx\n", + (u64)(*vstart) + (*phys_offset), + (u64)(*vstart) + (*phys_offset) + (*size) - 1); + } else + return 1; + return 0; +} + +int arch_memory_test_prepare(u32 *vstart, u32 *size, phys_addr_t *phys_offset) +{ + phys_size_t p_size = min(gd->ram_size, CONFIG_MAX_MEM_MAPPED); + *vstart = CONFIG_SYS_DDR_SDRAM_BASE; + *size = (u32) p_size; /* CONFIG_MAX_MEM_MAPPED < 4G */ + *phys_offset = 0; +#if !defined(CONFIG_PHYS_64BIT) || \ + !defined(CONFIG_SYS_INIT_RAM_ADDR_PHYS) || \ + (CONFIG_SYS_INIT_RAM_ADDR_PHYS < 0x100000000ull) + if (gd->ram_size > CONFIG_MAX_MEM_MAPPED) { + puts("Cannot test more than "); + print_size(CONFIG_MAX_MEM_MAPPED, + " without proper 36BIT support.\n"); + } +#endif + printf("Testing 0x%08llx - 0x%08llx\n", + (u64)(*vstart) + (*phys_offset), + (u64)(*vstart) + (*phys_offset) + (*size) - 1); + return 0; +} +int arch_memory_test_cleanup(u32 *vstart, u32 *size, phys_addr_t *phys_offset) +{ + unsigned long epn; + u32 tsize, valid, ptr; + phys_addr_t rpn = 0; + int ddr_esel; + /* disable the TLBs for this testing */ + ptr = *vstart; + while (ptr < (*vstart) + (*size)) { + ddr_esel = find_tlb_idx((void *)ptr, 1); + if (ddr_esel != -1) { + read_tlbcam_entry(ddr_esel, &valid, &tsize, &epn, &rpn); + disable_tlb(ddr_esel); + } + ptr += TSIZE_TO_BYTES(tsize); + } + puts("Remap DDR "); + setup_ddr_tlbs(gd->ram_size>>20); + puts("\n"); + return 0; +} + +void arch_memory_failure_handle(void) +{ + dump_spd_ddr_reg(); +} +#endif diff --git a/arch/powerpc/cpu/mpc85xx/tlb.c b/arch/powerpc/cpu/mpc85xx/tlb.c index f2833a5..019fab7 100644 --- a/arch/powerpc/cpu/mpc85xx/tlb.c +++ b/arch/powerpc/cpu/mpc85xx/tlb.c @@ -245,7 +245,8 @@ void init_addr_map(void) } #endif -unsigned int setup_ddr_tlbs(unsigned int memsize_in_meg) +unsigned int +__setup_ddr_tlbs(phys_addr_t p_addr, unsigned int memsize_in_meg) { int i; unsigned int tlb_size; @@ -275,21 +276,24 @@ unsigned int setup_ddr_tlbs(unsigned int memsize_in_meg) tlb_size = (camsize - 10) / 2; - set_tlb(1, ram_tlb_address, ram_tlb_address, + set_tlb(1, ram_tlb_address, p_addr, MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, ram_tlb_index, tlb_size, 1); size -= 1ULL << camsize; memsize -= 1ULL << camsize; ram_tlb_address += 1UL << camsize; + p_addr += 1UL << camsize; } if (memsize) print_size(memsize, " left unmapped\n"); - - /* - * Confirm that the requested amount of memory was mapped. - */ return memsize_in_meg; } + +unsigned int setup_ddr_tlbs(unsigned int memsize_in_meg) +{ + return + __setup_ddr_tlbs(CONFIG_SYS_DDR_SDRAM_BASE, memsize_in_meg); +} #endif /* !CONFIG_NAND_SPL */ diff --git a/doc/README.fsl-ddr b/doc/README.fsl-ddr index e108a0d..20f531d 100644 --- a/doc/README.fsl-ddr +++ b/doc/README.fsl-ddr @@ -78,9 +78,28 @@ If the DDR controller supports address hashing, it can be enabled by hwconfig. Syntax is: hwconfig=fsl_ddr:addr_hash=true + +Memory testing options for mpc85xx +================================== +1. Memory test can be done one U-boot prompt comes up using mtest, or +2. Memory test can be done with Power-On-Self-Test function, activated at compile time + and by hwconfig. + + In order to enable the POST memory test, CONFIG_POST needs to be + defined in board configuraiton header file. By default, POST memory test performs + a fast test. A slow test can be enabled by changing the flag, or hwconfig can + be used to active slow test. To test memory bigger than 2GB, 36BIT support is + needed. Memory is tested within a 2GB window. TLBs are used to map the virtual + 2GB window to physical address so that all physical memory can be tested. + + Syntax of hwconfig + hwconfig=memtest:slow or + hwconfig=memtest:fast + Combination of hwconfig ======================= Hwconfig can be combined with multiple parameters, for example, on a supported platform -hwconfig=fsl_ddr:addr_hash=true,ctlr_intlv=cacheline,bank_intlv=cs0_cs1_cs2_cs3 +hwconfig=fsl_ddr:addr_hash=true,ctlr_intlv=cacheline,bank_intlv=cs0_cs1_cs2_cs3,;memtest=slow + -- 1.7.0.4 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot