On Mon, May 25, 2020 at 7:52 PM Pragnesh Patel <pragnesh.pa...@sifive.com> wrote: > > Hi Bin, > > >-----Original Message----- > >From: Bin Meng <bmeng...@gmail.com> > >Sent: 25 May 2020 18:42 > >To: Pragnesh Patel <pragnesh.pa...@sifive.com> > >Cc: U-Boot Mailing List <u-boot@lists.denx.de>; Atish Patra > ><atish.pa...@wdc.com>; Palmer Dabbelt <palmerdabb...@google.com>; Paul > >Walmsley <paul.walms...@sifive.com>; Jagan Teki > ><ja...@amarulasolutions.com>; Anup Patel <anup.pa...@wdc.com>; Sagar > >Kadam <sagar.ka...@sifive.com>; Rick Chen <r...@andestech.com> > >Subject: Re: [PATCH v12 00/18] RISC-V SiFive FU540 support SPL > > > >[External Email] Do not click links or attachments unless you recognize the > >sender and know the content is safe > > > >Hi Pragnesh, > > > >On Mon, May 25, 2020 at 3:33 PM Pragnesh Patel > ><pragnesh.pa...@sifive.com> wrote: > >> > >> This series add support for SPL to FU540. U-Boot SPL can boot from > >> L2 LIM (0x0800_0000) and jump to OpenSBI(FW_DYNAMIC firmware) and > >> U-Boot proper from MMC devices. > >> > >> This series is also available here [1] for testing [1] > >> https://github.com/pragnesh26992/u-boot/tree/spl > >> > >> How to test this patch: > >> 1) Go to OpenSBI-dir : make PLATFORM=generic FW_DYNAMIC=y > >> 2) export OPENSBI=<path to > >> opensbi/build/platform/generic/firmware/fw_dynamic.bin> > >> 3) Change to u-boot-dir > >> 4) make sifive_fu540_defconfig > >> 5) make all > >> 6) Format the SD card (make sure the disk has GPT, otherwise use gdisk > >> to switch) > >> > >> # sudo sgdisk --clear \ > >> > --set-alignment=2 \ > >> > --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300- > >FC78-40CD-8002-E86C45580B47 \ > >> > --new=2:2082:10273 --change-name=2:loader2 -- > >typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \ > >> > --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF- > >8483-4772-8E79-3D69D8477DE4 \ > >> > /dev/sda > >> > >> 7) sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34 > >> 8) sudo dd if=u-boot.itb of=/dev/sda seek=2082 > >> > >> Changes in v12: > >> - Rebase on mainline U-Boot > >> Added necessary include files which are not part of common header now > >> Remove unnecessary include files > >> > >> drivers/misc/sifive-otp.c > >> +#include <linux/bitops.h> > >> +#include <linux/delay.h> > >> > >> board/sifive/fu540/fu540.c > >> -#include <common.h> > >> +#include <log.h> > >> > >> board/sifive/fu540/spl.c > >> +#include <init.h> > >> +#include <log.h> > >> +#include <linux/delay.h> > >> > >> drivers/ram/sifive/fu540_ddr.c > >> +#include <linux/bitops.h> > >> > >> arch/riscv/cpu/fu540/cpu.c > >> -#include <common.h> > >> +#include <asm/cache.h> > >> > >> arch/riscv/cpu/fu540/spl.c > >> -#include <common.h> > >> +#include <log.h> > >> > >> board/sifive/fu540/spl.c > >> -#include <common.h> > >> +#include <init.h> > >> +#include <log.h> > >> +#include <linux/delay.h> > >> > >> - Update commit description for Release ethernet clock reset > >> - Update OpenSBI building section in "doc/board/sifive/fu540.rst" > >> > > > >Thanks. During the testing I found there is one issue about ethernet. > > > >The 1000Mbps does not work. Only 100Mbps works. Could you please have a > >look? > > Yes, you are right. This is because ethernet clock rate is not setting > properly. > > FSBL set the ethernet clock rate to 125 Mhz. > https://github.com/sifive/freedom-u540-c000-bootloader/blob/master/fsbl/main.c#L256 > > > U-Boot can do the same with below lines: > > eth0: ethernet@10090000 { > +assigned-clocks = <&prci PRCI_CLK_GEMGXLPLL>; > +assigned-clock-rates = <125000000>; > }; > > I will update this in v13, thanks for the testing.
Please share your latest version, I will update the partition table. Jagan.