Hi Heinrich, On Tue, 25 Aug 2020 at 04:12, Heinrich Schuchardt <xypron.g...@gmx.de> wrote: > > On 25.08.20 06:07, Heinrich Schuchardt wrote: > > On 8/22/20 4:36 AM, Simon Glass wrote: > >> This series allows binman to generate FITs that include multiple DTB > >> images and the configuration to use them. > >> > >> It is then possible to remove the sunxi FIT generator script, so this > >> series handles that also. > >> > >> With this, sunxi is fully converted to use binman. > > > > I have applied this patch series and it does not work on my > > pine64-lts_defconfig. > > > > Environment variable BL31 points to my bl31.bin: > > > > $ echo $BL31 > > ../trusted-firmware-a/build/sun50i_a64/debug/bl31.bin > > > > U-Boot SPL 2020.10-rc2-00147-g72293dc579 (Aug 25 2020 - 03:29:28 +0000) > > DRAM: 2048 MiB > > Trying to boot from MMC1 > > No matching DT out of these options: > > Configuration to load ATF before U-Boot > > No matching DT out of these options: > > Configuration to load ATF before U-Boot > > mmc_load_image_raw_sector: mmc block read error > > SPL: failed to boot from all boot devices > > ### ERROR ### Please RESET the board ### > > > > Without your patches U-Boot works. But CONFIG_SYS_MALLOC_F_LEN=0x400 is > > too small. This results in a warning "alloc space exhausted". Cf. > > https://patchwork.ozlabs.org/project/uboot/patch/20200725181851.4339-1-xypron.g...@gmx.de/ > > > > U-Boot SPL 2020.10-rc2-00140-g1aa3966173 (Aug 25 2020 - 03:46:36 +0000) > > DRAM: 2048 MiB > > Trying to boot from MMC1 > > NOTICE: BL31: v2.2():v2.2-1138-g78460ced4 > > NOTICE: BL31: Built : 05:50:47, Apr 7 2020 > > NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689) > > NOTICE: BL31: Found U-Boot DTB at 0x4092cc8, model: Pine64 LTS > > INFO: ARM GICv2 driver initialized > > INFO: Configuring SPC Controller > > INFO: PMIC: Probing AXP803 on RSB > > INFO: PMIC: dcdc1 voltage: 3.300V > > INFO: PMIC: dcdc5 voltage: 1.200V > > INFO: PMIC: dcdc6 voltage: 1.100V > > INFO: PMIC: dldo1 voltage: 3.300V > > INFO: PMIC: dldo2 voltage: 3.300V > > INFO: PMIC: dldo4 voltage: 3.300V > > INFO: PMIC: fldo1 voltage: 1.200V > > INFO: PMIC: Enabling DC SW > > INFO: BL31: Platform setup done > > INFO: BL31: Initializing runtime services > > INFO: BL31: cortex_a53: CPU workaround for 843419 was applied > > INFO: BL31: cortex_a53: CPU workaround for 855873 was applied > > NOTICE: PSCI: System suspend is unavailable > > INFO: BL31: Preparing for EL3 exit to normal world > > INFO: Entry point address = 0x4a000000 > > INFO: SPSR = 0x3c9 > > alloc space exhausted > > > > > > U-Boot 2020.10-rc2-00140-g1aa3966173 (Aug 25 2020 - 03:46:36 +0000) > > Allwinner Technology > > > > CPU: Allwinner A64 (SUN50I) > > Model: Pine64 LTS > > DRAM: 2 GiB > > MMC: mmc@1c0f000: 0, mmc@1c11000: 1 > > Loading Environment from FAT... Card did not respond to voltage select! > > In: serial > > Out: serial > > Err: serial > > Net: phy interface7 > > eth0: ethernet@1c30000 > > Hit any key to stop autoboot: 0 > > > > Best regards > > > > Heinrich > > This is u-boot.its created without your patches: > > /dts-v1/; > > / { > description = "Configuration to load ATF before U-Boot"; > #address-cells = <1>; > > images { > uboot { > description = "U-Boot (64-bit)"; > data = /incbin/("u-boot-nodtb.bin"); > type = "standalone"; > arch = "arm64"; > compression = "none"; > load = <0x4a000000>; > }; > atf { > description = "ARM Trusted Firmware"; > data = > /incbin/("../trusted-firmware-a/build/sun50i_a64/debug/bl31.bin"); > type = "firmware"; > arch = "arm64"; > compression = "none"; > load = <0x44000>; > entry = <0x44000>; > }; > fdt_1 { > description = "sun50i-a64-pine64-lts"; > data = > /incbin/("arch/arm/dts/sun50i-a64-pine64-lts.dtb"); > type = "flat_dt"; > compression = "none"; > }; > }; > configurations { > default = "config_1"; > > config_1 { > description = "sun50i-a64-pine64-lts"; > firmware = "uboot"; > loadables = "atf"; > fdt = "fdt_1"; > }; > }; > }; > > This is the itb that is created with your patches: > > /dts-v1/; > > / { > description = "Configuration to load ATF before U-Boot"; > #address-cells = < 0x01 >; > > images { > > uboot { > data = < 0x1f000 ... > description = "U-Boot (64-bit)"; > type = "standalone"; > arch = "arm64"; > compression = "none"; > load = < 0x4a000000 >; > }; > > atf { > data = [ f4 ... > description = "ARM Trusted Firmware"; > type = "firmware"; > arch = "arm64"; > compression = "none"; > load = < 0x44000 >; > entry = < 0x44000 >; > }; > }; > > configurations { > default = "config-1"; > }; > }; > > > The device tree is missing and the default configuration is empty.
There was a thread on this, I thought. Can you check u-boot-dm/binman-working ? I can send v2 I suppose. Regards, Simon