On 05.12.2020 12:02, Eugen Hristev wrote: > Hello, > > This series adds support for sama7g5 SoC DT and the sama7g5ek board. > I kept the original incremental development for this board, with each > commit's author and designated change, for traceability and for easier > reviewing. > > The series starts from a basic devicetree and ends with a fully functional > board including SD-Card/MMC, i2c eeproms, ethernet. > > Thanks, > Eugen > > Changes in v2: > - fixed compatible for i2c eeprom, mac was not read correctly in latest > u-boot version > - fixed some checkpatch warnings and some spacing > > Claudiu Beznea (20): > board: atmel: sama7g5ek: add SYS_MALLOC_F_LEN to SYS_INIT_SP_ADDR > configs: sama7g5ek: set malloc pool to 68K > configs: sama7g5ek: enable pll driver > ARM: dts: sama7g5: move clock frequencies for xtals in board file > ARM: dts: sama7g5: add slow rc and main rc oscillators > ARM: dts: sama7g5: add u-boot,dm-pre-reloc bindings for xtals > ARM: dts: sama7g5: add slow clock bindings > ARM: dts: sama7g5: add PMC bindings > ARM: dts: sama7g5: switch to PMC bindings > configs: sama7g5: enable CONFIG_CPU > ARM: dts: sama7g5: add CPU bindings > configs: sama7g5: use PIT64B > ARM: dts: sama7g5: enable autoboot > ARM: dts: sama7g5: add pit64b support > configs: sama7g5ek: enable mii command > ARM: dts: sama7g5: add GMAC0 > ARM: dts: sama7g5: add GMAC1 > board: atmel: sama7g5ek: increase arp timeout and retry count > configs: sama7g5ek: enable support for KSZ9131 > configs: sama7g5ek: enable CCF > > Eugen Hristev (13): > ARM: dts: sama7g5: add initial DT for sama7g5 SoC > board: atmel: sama7g5ek: add initial support for sama7g5ek > ARM: dts: at91: sama7g5: add pinctrl node > ARM: dts: at91: sama7g5ek: add pinctrl for sdmmc1 and flx3 > ARM: dts: at91: sama7g5: add assigned clocks for sdmmc1 > ARM: dts: at91: sama7g5: add node for sdmmc0 > ARM: dts: at91: sama7g5ek: enable sdmmc0 with pinctrl > board: atmel: sama7g5ek: clean-up header bootcommand > configs: sama7g5: add mmc config for sdmmc0 > ARM: dts: at91: sama7g5: add flexcom1 and i2c subnode > ARM: dts: sama7g5ek: add i2c1 bus and eeproms > board: atmel: sama7g5ek: add support for MAC address retreival > configs: sama7g5ek: add i2c and eeprom > > Nicolas Ferre (1): > ARM: dts: sama7g5ek: fix TXC pin configuration > > arch/arm/dts/Makefile | 3 + > arch/arm/dts/sama7g5.dtsi | 170 ++++++++++++++++++++++++ > arch/arm/dts/sama7g5ek-u-boot.dtsi | 65 ++++++++++ > arch/arm/dts/sama7g5ek.dts | 202 +++++++++++++++++++++++++++++ > arch/arm/mach-at91/Kconfig | 8 ++ > board/atmel/sama7g5ek/Kconfig | 15 +++ > board/atmel/sama7g5ek/MAINTAINERS | 8 ++ > board/atmel/sama7g5ek/Makefile | 7 + > board/atmel/sama7g5ek/sama7g5ek.c | 76 +++++++++++ > configs/sama7g5ek_mmc1_defconfig | 70 ++++++++++ > configs/sama7g5ek_mmc_defconfig | 70 ++++++++++ > include/configs/sama7g5ek.h | 45 +++++++ > 12 files changed, 739 insertions(+) > create mode 100644 arch/arm/dts/sama7g5.dtsi > create mode 100644 arch/arm/dts/sama7g5ek-u-boot.dtsi > create mode 100644 arch/arm/dts/sama7g5ek.dts > create mode 100644 board/atmel/sama7g5ek/Kconfig > create mode 100644 board/atmel/sama7g5ek/MAINTAINERS > create mode 100644 board/atmel/sama7g5ek/Makefile > create mode 100644 board/atmel/sama7g5ek/sama7g5ek.c > create mode 100644 configs/sama7g5ek_mmc1_defconfig > create mode 100644 configs/sama7g5ek_mmc_defconfig > create mode 100644 include/configs/sama7g5ek.h >
Applied to u-boot-atmel/master