This adds some registers needed for DUAL/QUAD/OCTAL modes. It also adds the
fields in (R)ISR so we can check for over-/under-flow.
Signed-off-by: Sean Anderson <sean...@gmail.com>
---
Changes in v2:
- Fix some inconsistencies in register naming and usage
drivers/spi/designware_spi.c | 60 ++++++++++++++++++++++++++++++++++--
1 file changed, 57 insertions(+), 3 deletions(-)
diff --git a/drivers/spi/designware_spi.c b/drivers/spi/designware_spi.c
index c2639141c6..e110c5bca1 100644
--- a/drivers/spi/designware_spi.c
+++ b/drivers/spi/designware_spi.c
@@ -56,6 +56,8 @@
#define DW_SPI_IDR 0x58
#define DW_SPI_VERSION 0x5c
#define DW_SPI_DR 0x60
+#define DW_SPI_RX_SAMPLE_DLY 0xf0
+#define DW_SPI_SPI_CTRL0 0xf4
/* Bit fields in CTRLR0 */
/*
@@ -80,8 +82,8 @@
#define CTRLR0_TMOD_RO 0x2 /* recv only */
#define CTRLR0_TMOD_EPROMREAD 0x3 /* eeprom read mode */
-#define CTRLR0_SLVOE_OFFSET 10
-#define CTRLR0_SRL_OFFSET 11
+#define CTRLR0_SLVOE_OFFSET BIT(10)
+#define CTRLR0_SRL BIT(11)
#define CTRLR0_CFS_MASK GENMASK(15, 12)
/* Only present when SSI_MAX_XFER_SIZE=32 */
@@ -92,13 +94,15 @@
#define CTRLR0_SPI_FRF_BYTE 0x0
#define CTRLR0_SPI_FRF_DUAL 0x1
#define CTRLR0_SPI_FRF_QUAD 0x2
+#define CTRLR0_SPI_FRF_OCTAL 0x3
/* Bit fields in CTRLR0 based on DWC_ssi_databook.pdf v1.01a */
#define DWC_SSI_CTRLR0_DFS_MASK GENMASK(4, 0)
#define DWC_SSI_CTRLR0_FRF_MASK GENMASK(7, 6)
#define DWC_SSI_CTRLR0_MODE_MASK GENMASK(9, 8)
#define DWC_SSI_CTRLR0_TMOD_MASK GENMASK(11, 10)
-#define DWC_SSI_CTRLR0_SRL_OFFSET 13
+#define DWC_SSI_CTRLR0_SRL BIT(13)
+#define DWC_SSI_CTRLR0_SSTE BIT(14)
#define DWC_SSI_CTRLR0_SPI_FRF_MASK GENMASK(23, 22)
/* Bit fields in SR, 7 bits */
@@ -111,6 +115,56 @@
#define SR_TX_ERR BIT(5)
#define SR_DCOL BIT(6)
+/* Bit fields in (R)ISR */
+
+/* TX FIFO Empty */
+#define ISR_TXEI BIT(0)
+/* TX FIFO Overflow */
+#define ISR_TXOI BIT(1)
+/* RX FIFO Underflow */
+#define ISR_RXUI BIT(2)
+/* RX FIFO Overflow */
+#define ISR_RXOI BIT(3)
+/* RX FIFO Full */
+#define ISR_RXFI BIT(4)
+/* Multi-master contention */
+#define ISR_MSTI BIT(5)
+/* XIP Receive FIFO Overflow */
+#define ISR_XRXOI BIT(6)
+/* TX FIFO Underflow */
+#define ISR_TXUI BIT(7)
+/* AXI Error */
+#define ISR_AXIE BIT(8)
+/* SPI TX Error */
+#define ISR_SPITE BIT(10)
+/* SSI Done */
+#define ISR_DONE BIT(11)
+
+/* Bit fields in SPI_CTRLR0 */
+
+/*
+ * Whether the instruction or address use the value of SPI_FRF or use
+ * FRF_BYTE
+ */
+#define SPI_CTRLR0_TRANS_TYPE_MASK GENMASK(1, 0)
+#define SPI_CTRLR0_TRANS_TYPE_1_1_X 0x0
+#define SPI_CTRLR0_TRANS_TYPE_1_X_X 0x1
+#define SPI_CTRLR0_TRANS_TYPE_X_X_X 0x2
+/* Address length in 4-bit units */
+#define SPI_CTRLR0_ADDR_L_MASK GENMASK(5, 2)
+/* Enable mode bits after address in XIP mode */
+#define SPI_CTRLR0_XIP_MD_BIT_EN BIT(7)
+/* Instruction length */
+#define SPI_CTRLR0_INST_L_MASK GENMASK(9, 8)
+#define INST_L_0 0x0
+#define INST_L_4 0x1
+#define INST_L_8 0x2
+#define INST_L_16 0x3
+/* Number of "dummy" cycles */
+#define SPI_CTRLR0_WAIT_CYCLES_MASK GENMASK(15, 11)
+/* Stretch the clock if the FIFO over/underflows */
+#define SPI_CTRLR0_CLK_STRETCH_EN BIT(30)
+
#define RX_TIMEOUT 1000 /* timeout in ms */
struct dw_spi_plat {
--
2.29.2
