This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Fabio Estevam <fabio.este...@nxp.com>
Signed-off-by: Tom Rini <tr...@konsulko.com>
---
arch/arm/mach-imx/mxs/Kconfig | 5 -
board/freescale/mx28evk/Kconfig | 15 --
board/freescale/mx28evk/MAINTAINERS | 9 -
board/freescale/mx28evk/Makefile | 10 --
board/freescale/mx28evk/README | 62 -------
board/freescale/mx28evk/iomux.c | 205 ---------------------
board/freescale/mx28evk/mx28evk.c | 150 ----------------
configs/mx28evk_auart_console_defconfig | 63 -------
configs/mx28evk_defconfig | 63 -------
configs/mx28evk_nand_defconfig | 64 -------
configs/mx28evk_spi_defconfig | 60 -------
include/configs/mx28evk.h | 226 ------------------------
12 files changed, 932 deletions(-)
delete mode 100644 board/freescale/mx28evk/Kconfig
delete mode 100644 board/freescale/mx28evk/MAINTAINERS
delete mode 100644 board/freescale/mx28evk/Makefile
delete mode 100644 board/freescale/mx28evk/README
delete mode 100644 board/freescale/mx28evk/iomux.c
delete mode 100644 board/freescale/mx28evk/mx28evk.c
delete mode 100644 configs/mx28evk_auart_console_defconfig
delete mode 100644 configs/mx28evk_defconfig
delete mode 100644 configs/mx28evk_nand_defconfig
delete mode 100644 configs/mx28evk_spi_defconfig
delete mode 100644 include/configs/mx28evk.h
diff --git a/arch/arm/mach-imx/mxs/Kconfig b/arch/arm/mach-imx/mxs/Kconfig
index e04b0dc10f6c..6a6e6ebecf0b 100644
--- a/arch/arm/mach-imx/mxs/Kconfig
+++ b/arch/arm/mach-imx/mxs/Kconfig
@@ -14,10 +14,6 @@ config TARGET_APX4DEVKIT
config TARGET_BG0900
bool "Support bg0900"
-config TARGET_MX28EVK
- bool "Support mx28evk"
- select BOARD_EARLY_INIT_F
-
config TARGET_SC_SPS_1
bool "Support sc_sps_1"
@@ -33,7 +29,6 @@ config SYS_SOC
default "mxs"
source "board/bluegiga/apx4devkit/Kconfig"
-source "board/freescale/mx28evk/Kconfig"
source "board/liebherr/xea/Kconfig"
source "board/ppcag/bg0900/Kconfig"
source "board/schulercontrol/sc_sps_1/Kconfig"
diff --git a/board/freescale/mx28evk/Kconfig b/board/freescale/mx28evk/Kconfig
deleted file mode 100644
index 39777bd70fae..000000000000
--- a/board/freescale/mx28evk/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_MX28EVK
-
-config SYS_BOARD
- default "mx28evk"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_SOC
- default "mxs"
-
-config SYS_CONFIG_NAME
- default "mx28evk"
-
-endif
diff --git a/board/freescale/mx28evk/MAINTAINERS
b/board/freescale/mx28evk/MAINTAINERS
deleted file mode 100644
index a98a70558a72..000000000000
--- a/board/freescale/mx28evk/MAINTAINERS
+++ /dev/null
@@ -1,9 +0,0 @@
-MX28EVK BOARD
-M: Fabio Estevam <fabio.este...@nxp.com>
-S: Maintained
-F: board/freescale/mx28evk/
-F: include/configs/mx28evk.h
-F: configs/mx28evk_defconfig
-F: configs/mx28evk_auart_console_defconfig
-F: configs/mx28evk_nand_defconfig
-F: configs/mx28evk_spi_defconfig
diff --git a/board/freescale/mx28evk/Makefile b/board/freescale/mx28evk/Makefile
deleted file mode 100644
index 057760433da9..000000000000
--- a/board/freescale/mx28evk/Makefile
+++ /dev/null
@@ -1,10 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, w...@denx.de.
-
-ifndef CONFIG_SPL_BUILD
-obj-y := mx28evk.o
-else
-obj-y := iomux.o
-endif
diff --git a/board/freescale/mx28evk/README b/board/freescale/mx28evk/README
deleted file mode 100644
index d32f0efb3326..000000000000
--- a/board/freescale/mx28evk/README
+++ /dev/null
@@ -1,62 +0,0 @@
-FREESCALE MX28EVK
-==================
-
-Supported hardware: MX28EVK rev C and D are supported in U-Boot.
-
-Files of the MX28EVK port
---------------------------
-
-arch/arm/cpu/arm926ejs/mxs/ - The CPU support code for the Freescale i.MX28
-arch/arm/include/asm/arch-mxs/ - Header files for the Freescale i.MX28
-board/freescale/mx28evk/ - MX28EVK board specific files
-include/configs/mx28evk.h - MX28EVK configuration file
-
-Jumper configuration
----------------------
-
-To boot MX28EVK from an SD card, set the boot mode DIP switches as:
-
- * Boot Mode Select: 1 0 0 1 (Boot from SD card Slot 0 - U42)
- * JTAG PSWITCH RESET: To the right (reset disabled)
- * Battery Source: Down
- * Wall 5V: Up
- * VDD 5V: To the left (off)
- * Hold Button: Down (off)
-
-To boot MX28EVK from SPI NOR flash, set the boot mode DIP switches as:
-
- * Boot Mode Select: 0 0 1 0 (Boot from SSP2)
- * JTAG PSWITCH RESET: To the right (reset disabled)
- * Battery Source: Down
- * Wall 5V: Up
- * VDD 5V: To the left (off)
- * Hold Button: Down (off)
-
-Environment Storage
--------------------
-
-There are three targets for mx28evk:
-
-"make mx28evk_config" - store environment variables into MMC
-
-or
-
-"make mx28evk_nand_config" - store environment variables into NAND flash
-
-or
-
-"make mx28evk_spi_config" - store environment variables into SPI NOR
flash
-
-Choose the target accordingly.
-
-Note: The mx28evk board does not come with a NAND flash populated from the
-factory. It comes with an empty slot (U23), which allows the insertion of a
-48-pin TSOP flash device.
-
-mx28evk does not come with SPI NOR flash populated from the factory either.
-It is possible to solder a SOIC memory on U49 or use a DIP8 on J89.
-To get SPI communication to work R320, R321,R322 and C178 need to be populated.
-Look in the schematics for the proper component values.
-
-Follow the instructions from doc/imx/common/mxs.txt to generate a bootable
-SD card or to generate a binary to be flashed into SPI NOR.
diff --git a/board/freescale/mx28evk/iomux.c b/board/freescale/mx28evk/iomux.c
deleted file mode 100644
index cc0c85885446..000000000000
--- a/board/freescale/mx28evk/iomux.c
+++ /dev/null
@@ -1,205 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Freescale MX28EVK IOMUX setup
- *
- * Copyright (C) 2011 Marek Vasut <marek.va...@gmail.com>
- * on behalf of DENX Software Engineering GmbH
- */
-
-#include <common.h>
-#include <config.h>
-#include <asm/io.h>
-#include <asm/arch/iomux-mx28.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/sys_proto.h>
-
-#define MUX_CONFIG_SSP0 (MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
-#define MUX_CONFIG_GPMI (MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_NOPULL)
-#define MUX_CONFIG_ENET (MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
-#define MUX_CONFIG_EMI (MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
-#define MUX_CONFIG_SSP2 (MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_PULLUP)
-#define MUX_CONFIG_LCD (MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_NOPULL)
-
-const iomux_cfg_t iomux_setup[] = {
- /* DUART */
- MX28_PAD_PWM0__DUART_RX,
- MX28_PAD_PWM1__DUART_TX,
-
- /* MMC0 */
- MX28_PAD_SSP0_DATA0__SSP0_D0 | MUX_CONFIG_SSP0,
- MX28_PAD_SSP0_DATA1__SSP0_D1 | MUX_CONFIG_SSP0,
- MX28_PAD_SSP0_DATA2__SSP0_D2 | MUX_CONFIG_SSP0,
- MX28_PAD_SSP0_DATA3__SSP0_D3 | MUX_CONFIG_SSP0,
- MX28_PAD_SSP0_DATA4__SSP0_D4 | MUX_CONFIG_SSP0,
- MX28_PAD_SSP0_DATA5__SSP0_D5 | MUX_CONFIG_SSP0,
- MX28_PAD_SSP0_DATA6__SSP0_D6 | MUX_CONFIG_SSP0,
- MX28_PAD_SSP0_DATA7__SSP0_D7 | MUX_CONFIG_SSP0,
- MX28_PAD_SSP0_CMD__SSP0_CMD | MUX_CONFIG_SSP0,
- MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
- (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
- MX28_PAD_SSP0_SCK__SSP0_SCK |
- (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
- /* write protect */
- MX28_PAD_SSP1_SCK__GPIO_2_12,
- /* MMC0 slot power enable */
- MX28_PAD_PWM3__GPIO_3_28 |
- (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
-
-#ifdef CONFIG_NAND_MXS
- /* GPMI NAND */
- MX28_PAD_GPMI_D00__GPMI_D0 | MUX_CONFIG_GPMI,
- MX28_PAD_GPMI_D01__GPMI_D1 | MUX_CONFIG_GPMI,
- MX28_PAD_GPMI_D02__GPMI_D2 | MUX_CONFIG_GPMI,
- MX28_PAD_GPMI_D03__GPMI_D3 | MUX_CONFIG_GPMI,
- MX28_PAD_GPMI_D04__GPMI_D4 | MUX_CONFIG_GPMI,
- MX28_PAD_GPMI_D05__GPMI_D5 | MUX_CONFIG_GPMI,
- MX28_PAD_GPMI_D06__GPMI_D6 | MUX_CONFIG_GPMI,
- MX28_PAD_GPMI_D07__GPMI_D7 | MUX_CONFIG_GPMI,
- MX28_PAD_GPMI_CE0N__GPMI_CE0N | MUX_CONFIG_GPMI,
- MX28_PAD_GPMI_RDY0__GPMI_READY0 | MUX_CONFIG_GPMI,
- MX28_PAD_GPMI_RDN__GPMI_RDN |
- (MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP),
- MX28_PAD_GPMI_WRN__GPMI_WRN | MUX_CONFIG_GPMI,
- MX28_PAD_GPMI_ALE__GPMI_ALE | MUX_CONFIG_GPMI,
- MX28_PAD_GPMI_CLE__GPMI_CLE | MUX_CONFIG_GPMI,
- MX28_PAD_GPMI_RESETN__GPMI_RESETN | MUX_CONFIG_GPMI,
-#endif
-
- /* FEC0 */
- MX28_PAD_ENET0_MDC__ENET0_MDC | MUX_CONFIG_ENET,
- MX28_PAD_ENET0_MDIO__ENET0_MDIO | MUX_CONFIG_ENET,
- MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MUX_CONFIG_ENET,
- MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MUX_CONFIG_ENET,
- MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MUX_CONFIG_ENET,
- MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MUX_CONFIG_ENET,
- MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MUX_CONFIG_ENET,
- MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MUX_CONFIG_ENET,
- MX28_PAD_ENET_CLK__CLKCTRL_ENET | MUX_CONFIG_ENET,
- /* FEC0 Enable */
- MX28_PAD_SSP1_DATA3__GPIO_2_15 |
- (MXS_PAD_12MA | MXS_PAD_3V3),
- /* FEC0 Reset */
- MX28_PAD_ENET0_RX_CLK__GPIO_4_13 |
- (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
-
- /* FEC1 */
- MX28_PAD_ENET0_COL__ENET1_TX_EN | MUX_CONFIG_ENET,
- MX28_PAD_ENET0_CRS__ENET1_RX_EN | MUX_CONFIG_ENET,
- MX28_PAD_ENET0_RXD2__ENET1_RXD0 | MUX_CONFIG_ENET,
- MX28_PAD_ENET0_RXD3__ENET1_RXD1 | MUX_CONFIG_ENET,
- MX28_PAD_ENET0_TXD2__ENET1_TXD0 | MUX_CONFIG_ENET,
- MX28_PAD_ENET0_TXD3__ENET1_TXD1 | MUX_CONFIG_ENET,
-
- /* EMI */
- MX28_PAD_EMI_D00__EMI_DATA0 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D01__EMI_DATA1 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D02__EMI_DATA2 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D03__EMI_DATA3 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D04__EMI_DATA4 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D05__EMI_DATA5 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D06__EMI_DATA6 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D07__EMI_DATA7 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D08__EMI_DATA8 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D09__EMI_DATA9 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D10__EMI_DATA10 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D11__EMI_DATA11 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D12__EMI_DATA12 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D13__EMI_DATA13 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D14__EMI_DATA14 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_D15__EMI_DATA15 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_ODT0__EMI_ODT0 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_DQM0__EMI_DQM0 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_ODT1__EMI_ODT1 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_DQM1__EMI_DQM1 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK | MUX_CONFIG_EMI,
- MX28_PAD_EMI_CLK__EMI_CLK | MUX_CONFIG_EMI,
- MX28_PAD_EMI_DQS0__EMI_DQS0 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_DQS1__EMI_DQS1 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN | MUX_CONFIG_EMI,
-
- MX28_PAD_EMI_A00__EMI_ADDR0 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_A01__EMI_ADDR1 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_A02__EMI_ADDR2 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_A03__EMI_ADDR3 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_A04__EMI_ADDR4 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_A05__EMI_ADDR5 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_A06__EMI_ADDR6 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_A07__EMI_ADDR7 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_A08__EMI_ADDR8 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_A09__EMI_ADDR9 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_A10__EMI_ADDR10 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_A11__EMI_ADDR11 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_A12__EMI_ADDR12 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_A13__EMI_ADDR13 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_A14__EMI_ADDR14 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_BA0__EMI_BA0 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_BA1__EMI_BA1 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_BA2__EMI_BA2 | MUX_CONFIG_EMI,
- MX28_PAD_EMI_CASN__EMI_CASN | MUX_CONFIG_EMI,
- MX28_PAD_EMI_RASN__EMI_RASN | MUX_CONFIG_EMI,
- MX28_PAD_EMI_WEN__EMI_WEN | MUX_CONFIG_EMI,
- MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
- MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
- MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
-
- /* SPI2 (for SPI flash) */
- MX28_PAD_SSP2_SCK__SSP2_SCK | MUX_CONFIG_SSP2,
- MX28_PAD_SSP2_MOSI__SSP2_CMD | MUX_CONFIG_SSP2,
- MX28_PAD_SSP2_MISO__SSP2_D0 | MUX_CONFIG_SSP2,
- MX28_PAD_SSP2_SS0__SSP2_D3 |
- (MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP),
- /* I2C */
- MX28_PAD_I2C0_SCL__I2C0_SCL,
- MX28_PAD_I2C0_SDA__I2C0_SDA,
-
- /* LCD */
- MX28_PAD_LCD_D00__LCD_D0 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D01__LCD_D1 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D02__LCD_D2 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D03__LCD_D3 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D04__LCD_D4 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D05__LCD_D5 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D06__LCD_D6 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D07__LCD_D7 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D08__LCD_D8 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D09__LCD_D9 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D10__LCD_D10 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D11__LCD_D11 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D12__LCD_D12 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D13__LCD_D13 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D14__LCD_D14 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D15__LCD_D15 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D16__LCD_D16 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D17__LCD_D17 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D18__LCD_D18 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D19__LCD_D19 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D20__LCD_D20 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D21__LCD_D21 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D22__LCD_D22 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_D23__LCD_D23 | MUX_CONFIG_LCD,
- MX28_PAD_LCD_RD_E__LCD_VSYNC | MUX_CONFIG_LCD,
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC | MUX_CONFIG_LCD,
- MX28_PAD_LCD_RS__LCD_DOTCLK | MUX_CONFIG_LCD,
- MX28_PAD_LCD_CS__LCD_ENABLE | MUX_CONFIG_LCD,
- MX28_PAD_LCD_RESET__GPIO_3_30 | MUX_CONFIG_LCD, /* LCD power */
- MX28_PAD_PWM2__GPIO_3_18 | MUX_CONFIG_LCD, /* LCD contrast */
-};
-
-#define HW_DRAM_CTL29 (0x74 >> 2)
-#define CS_MAP 0xf
-#define COLUMN_SIZE 0x2
-#define ADDR_PINS 0x1
-#define APREBIT 0xa
-
-#define HW_DRAM_CTL29_CONFIG (CS_MAP << 24 | COLUMN_SIZE << 16 | \
- ADDR_PINS << 8 | APREBIT)
-
-void mxs_adjust_memory_params(uint32_t *dram_vals)
-{
- dram_vals[HW_DRAM_CTL29] = HW_DRAM_CTL29_CONFIG;
-}
-
-void board_init_ll(const uint32_t arg, const uint32_t *resptr)
-{
- mxs_common_spl_init(arg, resptr, iomux_setup, ARRAY_SIZE(iomux_setup));
-}
diff --git a/board/freescale/mx28evk/mx28evk.c
b/board/freescale/mx28evk/mx28evk.c
deleted file mode 100644
index a6b66d99ccb1..000000000000
--- a/board/freescale/mx28evk/mx28evk.c
+++ /dev/null
@@ -1,150 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Freescale MX28EVK board
- *
- * (C) Copyright 2011 Freescale Semiconductor, Inc.
- *
- * Author: Fabio Estevam <fabio.este...@freescale.com>
- *
- * Based on m28evk.c:
- * Copyright (C) 2011 Marek Vasut <marek.va...@gmail.com>
- * on behalf of DENX Software Engineering GmbH
- */
-
-#include <common.h>
-#include <init.h>
-#include <net.h>
-#include <asm/gpio.h>
-#include <asm/io.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux-mx28.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/sys_proto.h>
-#include <linux/delay.h>
-#include <linux/mii.h>
-#include <miiphy.h>
-#include <netdev.h>
-#include <errno.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * Functions
- */
-int board_early_init_f(void)
-{
- /* IO0 clock at 480MHz */
- mxs_set_ioclk(MXC_IOCLK0, 480000);
- /* IO1 clock at 480MHz */
- mxs_set_ioclk(MXC_IOCLK1, 480000);
-
- /* SSP0 clock at 96MHz */
- mxs_set_sspclk(MXC_SSPCLK0, 96000, 0);
- /* SSP2 clock at 160MHz */
- mxs_set_sspclk(MXC_SSPCLK2, 160000, 0);
-
-#ifdef CONFIG_CMD_USB
- mxs_iomux_setup_pad(MX28_PAD_SSP2_SS1__USB1_OVERCURRENT);
- mxs_iomux_setup_pad(MX28_PAD_AUART2_RX__GPIO_3_8 |
- MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL);
- gpio_direction_output(MX28_PAD_AUART2_RX__GPIO_3_8, 1);
-#endif
-
- /* Power on LCD */
- gpio_direction_output(MX28_PAD_LCD_RESET__GPIO_3_30, 1);
-
- /* Set contrast to maximum */
- gpio_direction_output(MX28_PAD_PWM2__GPIO_3_18, 1);
-
- return 0;
-}
-
-int dram_init(void)
-{
- return mxs_dram_init();
-}
-
-int board_init(void)
-{
- /* Adress of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
- return 0;
-}
-
-#ifdef CONFIG_CMD_MMC
-static int mx28evk_mmc_wp(int id)
-{
- if (id != 0) {
- printf("MXS MMC: Invalid card selected (card id = %d)\n", id);
- return 1;
- }
-
- return gpio_get_value(MX28_PAD_SSP1_SCK__GPIO_2_12);
-}
-
-int board_mmc_init(struct bd_info *bis)
-{
- /* Configure WP as input */
- gpio_direction_input(MX28_PAD_SSP1_SCK__GPIO_2_12);
-
- /* Configure MMC0 Power Enable */
- gpio_direction_output(MX28_PAD_PWM3__GPIO_3_28, 0);
-
- return mxsmmc_initialize(bis, 0, mx28evk_mmc_wp, NULL);
-}
-#endif
-
-#ifdef CONFIG_CMD_NET
-
-int board_eth_init(struct bd_info *bis)
-{
- struct mxs_clkctrl_regs *clkctrl_regs =
- (struct mxs_clkctrl_regs *)MXS_CLKCTRL_BASE;
- struct eth_device *dev;
- int ret;
-
- ret = cpu_eth_init(bis);
- if (ret)
- return ret;
-
- /* MX28EVK uses ENET_CLK PAD to drive FEC clock */
- writel(CLKCTRL_ENET_TIME_SEL_RMII_CLK | CLKCTRL_ENET_CLK_OUT_EN,
- &clkctrl_regs->hw_clkctrl_enet);
-
- /* Power-on FECs */
- gpio_direction_output(MX28_PAD_SSP1_DATA3__GPIO_2_15, 0);
-
- /* Reset FEC PHYs */
- gpio_direction_output(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 0);
- udelay(200);
- gpio_set_value(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 1);
-
- ret = fecmxc_initialize_multi(bis, 0, 0, MXS_ENET0_BASE);
- if (ret) {
- puts("FEC MXS: Unable to init FEC0\n");
- return ret;
- }
-
- ret = fecmxc_initialize_multi(bis, 1, 3, MXS_ENET1_BASE);
- if (ret) {
- puts("FEC MXS: Unable to init FEC1\n");
- return ret;
- }
-
- dev = eth_get_dev_by_name("FEC0");
- if (!dev) {
- puts("FEC MXS: Unable to get FEC0 device entry\n");
- return -EINVAL;
- }
-
- dev = eth_get_dev_by_name("FEC1");
- if (!dev) {
- puts("FEC MXS: Unable to get FEC1 device entry\n");
- return -EINVAL;
- }
-
- return ret;
-}
-
-#endif
diff --git a/configs/mx28evk_auart_console_defconfig
b/configs/mx28evk_auart_console_defconfig
deleted file mode 100644
index ec4fd6585ee5..000000000000
--- a/configs/mx28evk_auart_console_defconfig
+++ /dev/null
@@ -1,63 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX28=y
-CONFIG_SYS_TEXT_BASE=0x40002000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x4000
-CONFIG_ENV_OFFSET=0x40000
-CONFIG_SPL_TEXT_BASE=0x00001000
-CONFIG_TARGET_MX28EVK=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="MXS_AUART,MXS_AUART_BASE=MXS_UARTAPP3_BASE"
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_ARCH_MISC_INIT=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND_TRIMFFS=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=gpmi-nand:3m(bootloader)ro,512k(environment),512k(redundant-environment),4m(kernel),512k(fdt),8m(ramdisk),-(filesystem)"
-CONFIG_CMD_UBI=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_VERSION_VARIABLE=y
-CONFIG_MXS_GPIO=y
-CONFIG_MMC_MXS=y
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_MXS=y
-CONFIG_MII=y
-CONFIG_CONS_INDEX=0
-CONFIG_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_USB_ETHER_SMSC95XX=y
-CONFIG_VIDEO=y
-CONFIG_SPLASH_SCREEN=y
-CONFIG_VIDEO_BMP_GZIP=y
-CONFIG_VIDEO_BMP_RLE8=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/mx28evk_defconfig b/configs/mx28evk_defconfig
deleted file mode 100644
index 4f0ed83bc1f0..000000000000
--- a/configs/mx28evk_defconfig
+++ /dev/null
@@ -1,63 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX28=y
-CONFIG_SYS_TEXT_BASE=0x40002000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x4000
-CONFIG_ENV_OFFSET=0x40000
-CONFIG_SPL_TEXT_BASE=0x00001000
-CONFIG_TARGET_MX28EVK=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_FIT=y
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_ARCH_MISC_INIT=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND_TRIMFFS=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=gpmi-nand:3m(bootloader)ro,512k(environment),512k(redundant-environment),4m(kernel),512k(fdt),8m(ramdisk),-(filesystem)"
-CONFIG_CMD_UBI=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_VERSION_VARIABLE=y
-CONFIG_MXS_GPIO=y
-CONFIG_MMC_MXS=y
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_MXS=y
-CONFIG_MII=y
-CONFIG_CONS_INDEX=0
-CONFIG_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_USB_ETHER_SMSC95XX=y
-CONFIG_VIDEO=y
-CONFIG_SPLASH_SCREEN=y
-CONFIG_VIDEO_BMP_GZIP=y
-CONFIG_VIDEO_BMP_RLE8=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/mx28evk_nand_defconfig b/configs/mx28evk_nand_defconfig
deleted file mode 100644
index 7d95b8fc52de..000000000000
--- a/configs/mx28evk_nand_defconfig
+++ /dev/null
@@ -1,64 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX28=y
-CONFIG_SYS_TEXT_BASE=0x40002000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x4000
-CONFIG_ENV_OFFSET=0x300000
-CONFIG_SPL_TEXT_BASE=0x00001000
-CONFIG_TARGET_MX28EVK=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_ENV_OFFSET_REDUND=0x380000
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_ARCH_MISC_INIT=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND_TRIMFFS=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=gpmi-nand:3m(bootloader)ro,512k(environment),512k(redundant-environment),4m(kernel),512k(fdt),8m(ramdisk),-(filesystem)"
-CONFIG_CMD_UBI=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_VERSION_VARIABLE=y
-CONFIG_MXS_GPIO=y
-CONFIG_MMC_MXS=y
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_MXS=y
-CONFIG_MII=y
-CONFIG_CONS_INDEX=0
-CONFIG_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_USB_ETHER_SMSC95XX=y
-CONFIG_VIDEO=y
-CONFIG_SPLASH_SCREEN=y
-CONFIG_VIDEO_BMP_GZIP=y
-CONFIG_VIDEO_BMP_RLE8=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/mx28evk_spi_defconfig b/configs/mx28evk_spi_defconfig
deleted file mode 100644
index e969d50af7fe..000000000000
--- a/configs/mx28evk_spi_defconfig
+++ /dev/null
@@ -1,60 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX28=y
-CONFIG_SYS_TEXT_BASE=0x40002000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x4000
-CONFIG_SPL_TEXT_BASE=0x00001000
-CONFIG_TARGET_MX28EVK=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_SYS_CONSOLE_IS_IN_ENV=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_ARCH_MISC_INIT=y
-# CONFIG_SPL_FRAMEWORK is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND_TRIMFFS=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=gpmi-nand:3m(bootloader)ro,512k(environment),512k(redundant-environment),4m(kernel),512k(fdt),8m(ramdisk),-(filesystem)"
-CONFIG_CMD_UBI=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_VERSION_VARIABLE=y
-CONFIG_MXS_GPIO=y
-CONFIG_MMC_MXS=y
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_NAND_MXS=y
-CONFIG_MII=y
-CONFIG_CONS_INDEX=0
-CONFIG_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_USB_ETHER_SMSC95XX=y
-CONFIG_VIDEO=y
-CONFIG_SPLASH_SCREEN=y
-CONFIG_VIDEO_BMP_GZIP=y
-CONFIG_VIDEO_BMP_RLE8=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h
deleted file mode 100644
index a65df4860810..000000000000
--- a/include/configs/mx28evk.h
+++ /dev/null
@@ -1,226 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2011 Freescale Semiconductor, Inc.
- * Author: Fabio Estevam <fabio.este...@freescale.com>
- *
- * Based on m28evk.h:
- * Copyright (C) 2011 Marek Vasut <marek.va...@gmail.com>
- * on behalf of DENX Software Engineering GmbH
- */
-#ifndef __CONFIGS_MX28EVK_H__
-#define __CONFIGS_MX28EVK_H__
-
-/* System configurations */
-#define CONFIG_MACH_TYPE MACH_TYPE_MX28EVK
-
-/* Memory configuration */
-#define PHYS_SDRAM_1 0x40000000 /* Base address */
-#define PHYS_SDRAM_1_SIZE 0x40000000 /* Max 1 GB RAM */
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-
-/* Environment */
-
-/* Environment is in MMC */
-
-/* Environment is in NAND */
-#if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND)
-#define CONFIG_ENV_RANGE (512 * 1024)
-#endif
-
-/* Environment is in SPI flash */
-
-/* UBI and NAND partitioning */
-
-/* FEC Ethernet on SoC */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_FEC_MXC
-#define CONFIG_FEC_MXC_MDIO_BASE MXS_ENET0_BASE
-#define CONFIG_MX28_FEC_MAC_IN_OCOTP
-#endif
-
-/* RTC */
-#ifdef CONFIG_CMD_DATE
-#define CONFIG_RTC_MXS
-#endif
-
-/* USB */
-#ifdef CONFIG_CMD_USB
-#define CONFIG_EHCI_MXS_PORT1
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
-#endif
-
-/* Framebuffer support */
-#ifdef CONFIG_VIDEO
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (512 << 10)
-#endif
-
-/* Boot Linux */
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_LOADADDR 0x42000000
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-
-/* Extra Environment */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "ubifs_file=filesystem.ubifs\0" \
- "update_nand_full_filename=u-boot.nand\0" \
- "update_nand_firmware_filename=u-boot.sb\0" \
- "update_nand_firmware_maxsz=0x100000\0" \
- "update_nand_stride=0x40\0" /* MX28 datasheet ch. 12.12 */ \
- "update_nand_count=0x4\0" /* MX28 datasheet ch. 12.12 */ \
- "update_nand_get_fcb_size=" /* Get size of FCB blocks */ \
- "nand device 0 ; " \
- "nand info ; " \
- "setexpr fcb_sz ${update_nand_stride} * ${update_nand_count};" \
- "setexpr update_nand_fcb ${fcb_sz} * ${nand_writesize}\0" \
- "update_nand_firmware_full=" /* Update FCB, DBBT and FW */ \
- "if tftp ${update_nand_full_filename} ; then " \
- "run update_nand_get_fcb_size ; " \
- "nand scrub -y 0x0 ${filesize} ; " \
- "nand write.raw ${loadaddr} 0x0 ${fcb_sz} ; " \
- "setexpr update_off ${loadaddr} + ${update_nand_fcb} ; " \
- "setexpr update_sz ${filesize} - ${update_nand_fcb} ; " \
- "nand write ${update_off} ${update_nand_fcb} ${update_sz} ; " \
- "fi\0" \
- "update_nand_firmware=" /* Update only firmware */ \
- "if tftp ${update_nand_firmware_filename} ; then " \
- "run update_nand_get_fcb_size ; " \
- "setexpr fcb_sz ${update_nand_fcb} * 2 ; " /* FCB + DBBT */ \
- "setexpr fw_sz ${update_nand_firmware_maxsz} * 2 ; " \
- "setexpr fw_off ${fcb_sz} + ${update_nand_firmware_maxsz};" \
- "nand erase ${fcb_sz} ${fw_sz} ; " \
- "nand write ${loadaddr} ${fcb_sz} ${filesize} ; " \
- "nand write ${loadaddr} ${fw_off} ${filesize} ; " \
- "fi\0" \
- "update_nand_kernel=" /* Update kernel */ \
- "mtdparts default; " \
- "nand erase.part kernel; " \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "${get_cmd} ${image}; " \
- "nand write ${loadaddr} kernel ${filesize}\0" \
- "update_nand_fdt=" /* Update fdt */ \
- "mtdparts default; " \
- "nand erase.part fdt; " \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "${get_cmd} ${fdt_file}; " \
- "nand write ${loadaddr} fdt ${filesize}\0" \
- "update_nand_filesystem=" /* Update filesystem */ \
- "mtdparts default; " \
- "nand erase.part filesystem; " \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "${get_cmd} ${ubifs_file}; " \
- "ubi part filesystem; " \
- "ubi create filesystem; " \
- "ubi write ${loadaddr} filesystem ${filesize}\0" \
- "nandargs=setenv bootargs console=${console_mainline},${baudrate} " \
- "rootfstype=ubifs ubi.mtd=6 root=ubi0_0 ${mtdparts}\0" \
- "nandboot=" /* Boot from NAND */ \
- "mtdparts default; " \
- "run nandargs; " \
- "nand read ${loadaddr} kernel 0x00400000; " \
- "if test ${boot_fdt} = yes; then " \
- "nand read ${fdt_addr} fdt 0x00080000; " \
- "bootz ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = no; then " \
- "bootz; " \
- "else " \
- "echo \"ERROR: Set boot_fdt to yes or no.\"; " \
- "fi; " \
- "fi\0" \
- "update_sd_firmware_filename=u-boot.sd\0" \
- "update_sd_firmware=" /* Update the SD firmware partition */ \
- "if mmc rescan ; then " \
- "if tftp ${update_sd_firmware_filename} ; then " \
- "setexpr fw_sz ${filesize} / 0x200 ; " /* SD block size */ \
- "setexpr fw_sz ${fw_sz} + 1 ; " \
- "mmc write ${loadaddr} 0x800 ${fw_sz} ; " \
- "fi ; " \
- "fi\0" \
- "script=boot.scr\0" \
- "image=zImage\0" \
- "console_fsl=ttyAM0\0" \
- "console_mainline=ttyAMA0\0" \
- "fdt_file=imx28-evk.dtb\0" \
- "fdt_addr=0x41000000\0" \
- "boot_fdt=try\0" \
- "ip_dyn=yes\0" \
- "mmcdev=0\0" \
- "mmcpart=2\0" \
- "mmcroot=/dev/mmcblk0p3 rw rootwait\0" \
- "mmcargs=setenv bootargs console=${console_mainline},${baudrate} " \
- "root=${mmcroot}\0" \
- "loadbootscript=" \
- "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source\0" \
- "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
- "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if run loadfdt; then " \
- "bootz ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootz; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootz; " \
- "fi;\0" \
- "netargs=setenv bootargs console=${console_mainline},${baudrate} " \
- "root=/dev/nfs " \
- "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
- "netboot=echo Booting from net ...; " \
- "run netargs; " \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "${get_cmd} ${image}; " \
- "if test ${boot_fdt} = yes; then " \
- "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootz ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootz; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi;" \
- "fi; " \
- "else " \
- "bootz; " \
- "fi;\0"
-
-#define CONFIG_BOOTCOMMAND \
- "mmc dev ${mmcdev}; if mmc rescan; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loadimage; then " \
- "run mmcboot; " \
- "else run netboot; " \
- "fi; " \
- "fi; " \
- "else run netboot; fi"
-
-/* The rest of the configuration is shared */
-#include <configs/mxs.h>
-
-#endif /* __CONFIGS_MX28EVK_H__ */
--
2.17.1
