Hi Andrey,
thanks for the review!
On 2021-02-12 19:16, ZHIZHIKIN Andrey wrote:
Hello Peter,
-----Original Message-----
From: Peter Bergin <pe...@berginkonsult.se>
Sent: Friday, February 12, 2021 2:57 PM
To: u-boot@lists.denx.de
Cc: Peter Bergin <pe...@berginkonsult.se>; ZHIZHIKIN Andrey
<andrey.zhizhi...@leica-geosystems.com>
Subject: [PATCH] doc: board: freescale: imx8mp_evk: update to newer versions
and change ATF_LOAD_ADDR
Update imx-atf and firmware-imx to latest released versions.
Update address of ATF_LOAD_ADDR that has changed to 0x490000 in imx-atf
commit 48733cb4e773a7584ced601de9d717efa3d73815.
Commit message is incorrect, ATF_LOAD_ADDR is actually set to 0x970000
Good catch and it is indeed wrong.
Add 'O=' to make instructions as one issue has been noticed where it was trouble
building directly inside u-boot source dir.
Signed-off-by: Peter Bergin <pe...@berginkonsult.se>
Cc: Andrey Zhizhikin <andrey.zhizhi...@leica-geosystems.com>
---
doc/board/freescale/imx8mp_evk.rst | 24 ++++++++++++------------
1 file changed, 12 insertions(+), 12 deletions(-)
diff --git a/doc/board/freescale/imx8mp_evk.rst
b/doc/board/freescale/imx8mp_evk.rst
index ccffcf7257..5ca3bb8199 100644
--- a/doc/board/freescale/imx8mp_evk.rst
+++ b/doc/board/freescale/imx8mp_evk.rst
@@ -18,7 +18,7 @@ Get and Build the ARM Trusted firmware
Note: $(srctree) is the U-Boot source directory Get ATF from:
https://source.codeaurora.org/external/imx/imx-atf
-branch: imx_5.4.47_2.2.0
+branch: imx_5.4.70_2.3.0
.. code-block:: bash
@@ -30,13 +30,13 @@ Get the ddr firmware
.. code-block:: bash
- $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.9.bin
- $ chmod +x firmware-imx-8.9.bin
- $ ./firmware-imx-8.9.bin
- $ cp firmware-imx-
8.9/firmware/ddr/synopsys/lpddr4_pmu_train_1d_dmem_201904.bin
$(srctree)/lpddr4_pmu_train_1d_dmem.bin
- $ cp firmware-imx-
8.9/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem_201904.bin
$(srctree)/lpddr4_pmu_train_1d_imem.bin
- $ cp firmware-imx-
8.9/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem_201904.bin
$(srctree)/lpddr4_pmu_train_2d_dmem.bin
- $ cp firmware-imx-
8.9/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem_201904.bin
$(srctree)/lpddr4_pmu_train_2d_imem.bin
+ $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.10.bin
+ $ chmod +x firmware-imx-8.10.bin
+ $ ./firmware-imx-8.10.bin
+ $ cp firmware-imx-
8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_dmem_202006.bin
$(srctree)/lpddr4_pmu_train_1d_dmem.bin
+ $ cp firmware-imx-
8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem_202006.bin
$(srctree)/lpddr4_pmu_train_1d_imem.bin
+ $ cp firmware-imx-
8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem_202006.bin
$(srctree)/lpddr4_pmu_train_2d_dmem.bin
+ $ cp
+ firmware-imx-
8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem_20200
+ 6.bin $(srctree)/lpddr4_pmu_train_2d_imem.bin
Build U-Boot
------------
@@ -44,15 +44,15 @@ Build U-Boot
.. code-block:: bash
$ export CROSS_COMPILE=aarch64-poky-linux-
- $ make imx8mp_evk_defconfig
- $ export ATF_LOAD_ADDR=0x960000
- $ make flash.bin
+ $ make O=build imx8mp_evk_defconfig
As a suggestion: maybe it is better to change the order here when `make O=build
imx8mp_evk_defconfig` called first, followed by copy of DDR firmware and ATF
binary.
This would make sure that the ./build folder would already exist at the time
copy operations are executed, and should make step-by-step instructions more
transparent.
Good suggestion.
+ $ export ATF_LOAD_ADDR=0x970000
+ $ make O=build flash.bin
Burn the flash.bin to the MicroSD card at offset 32KB:
.. code-block:: bash
- $sudo dd if=flash.bin of=/dev/sd[x] bs=1K seek=32 conv=notrunc; sync
+ $sudo dd if=build/flash.bin of=/dev/sd[x] bs=1K seek=32
+ conv=notrunc; sync
Boot
----
--
2.25.1
Otherwise:
Reviewed-by: Andrey Zhizhikin <andrey.zhizhi...@leica-geosystems.com>
Cheers,
Andrey
Will update and send a v2 on this.
Best regards,
/Peter
