[PATCH v2 11/12] arm: am335x: add support for i2c2 bus

[Kory Maincent]

The am335x from BeagleBone use i2c EEPROM to detect capes.
The memory is wired to i2c bus 2 therefore it need to be enabled.

Add i2c2 clock, pinmux description and pinmux enable function.

Signed-off-by: Kory Maincent <kory.mainc...@bootlin.com>
---
 arch/arm/mach-omap2/am33xx/clock_am33xx.c |  1 +
 board/ti/am335x/board.c                   |  2 ++
 board/ti/am335x/board.h                   |  1 +
 board/ti/am335x/mux.c                     | 15 +++++++++++++++
 4 files changed, 19 insertions(+)

diff --git a/arch/arm/mach-omap2/am33xx/clock_am33xx.c 
b/arch/arm/mach-omap2/am33xx/clock_am33xx.c
index 2427933c8b..7c67444024 100644
--- a/arch/arm/mach-omap2/am33xx/clock_am33xx.c
+++ b/arch/arm/mach-omap2/am33xx/clock_am33xx.c
@@ -220,6 +220,7 @@ void enable_basic_clocks(void)
                &cmper->gpio2clkctrl,
                &cmper->gpio3clkctrl,
                &cmper->i2c1clkctrl,
+               &cmper->i2c2clkctrl,
                &cmper->cpgmac0clkctrl,
                &cmper->spi0clkctrl,
                &cmrtc->rtcclkctrl,
diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
index 984cc5e3ba..56cdda856c 100644
--- a/board/ti/am335x/board.c
+++ b/board/ti/am335x/board.c
@@ -76,8 +76,10 @@ static struct ctrl_dev *cdev = (struct ctrl_dev 
*)CTRL_DEVICE_BASE;
 void do_board_detect(void)
 {
        enable_i2c0_pin_mux();
+       enable_i2c2_pin_mux();
 #ifndef CONFIG_DM_I2C
        i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
+       i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED2, CONFIG_SYS_OMAP24_I2C_SLAVE2);
 #endif
        if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
                                 CONFIG_EEPROM_CHIP_ADDRESS))
diff --git a/board/ti/am335x/board.h b/board/ti/am335x/board.h
index 48df914af9..c2962111c1 100644
--- a/board/ti/am335x/board.h
+++ b/board/ti/am335x/board.h
@@ -93,5 +93,6 @@ void enable_uart3_pin_mux(void);
 void enable_uart4_pin_mux(void);
 void enable_uart5_pin_mux(void);
 void enable_i2c0_pin_mux(void);
+void enable_i2c2_pin_mux(void);
 void enable_board_pin_mux(void);
 #endif
diff --git a/board/ti/am335x/mux.c b/board/ti/am335x/mux.c
index 6fb2c009ba..78dc0cca42 100644
--- a/board/ti/am335x/mux.c
+++ b/board/ti/am335x/mux.c
@@ -124,6 +124,14 @@ static struct module_pin_mux i2c1_pin_mux[] = {
        {-1},
 };
 
+static struct module_pin_mux i2c2_pin_mux[] = {
+       {OFFSET(uart1_ctsn), (MODE(3) | RXACTIVE |
+                       PULLUDEN | PULLUP_EN | SLEWCTRL)},      /* I2C_DATA */
+       {OFFSET(uart1_rtsn), (MODE(3) | RXACTIVE |
+                       PULLUDEN | PULLUP_EN | SLEWCTRL)},      /* I2C_SCLK */
+       {-1},
+};
+
 static struct module_pin_mux spi0_pin_mux[] = {
        {OFFSET(spi0_sclk), (MODE(0) | RXACTIVE | PULLUDEN)},   /* SPI0_SCLK */
        {OFFSET(spi0_d0), (MODE(0) | RXACTIVE |
@@ -308,6 +316,11 @@ void enable_i2c0_pin_mux(void)
        configure_module_pin_mux(i2c0_pin_mux);
 }
 
+void enable_i2c2_pin_mux(void)
+{
+       configure_module_pin_mux(i2c2_pin_mux);
+}
+
 /*
  * The AM335x GP EVM, if daughter card(s) are connected, can have 8
  * different profiles.  These profiles determine what peripherals are
@@ -367,6 +380,7 @@ void enable_board_pin_mux(void)
 #else
                configure_module_pin_mux(mmc1_pin_mux);
 #endif
+               configure_module_pin_mux(i2c2_pin_mux);
        } else if (board_is_gp_evm()) {
                /* General Purpose EVM */
                unsigned short profile = detect_daughter_board_profile();
@@ -411,6 +425,7 @@ void enable_board_pin_mux(void)
 #else
                configure_module_pin_mux(mmc1_pin_mux);
 #endif
+               configure_module_pin_mux(i2c2_pin_mux);
        } else if (board_is_pb()) {
                configure_module_pin_mux(mii1_pin_mux);
                configure_module_pin_mux(mmc0_pin_mux);
-- 
2.17.1