On 11.04.21 20:47, Marek Vasut wrote:
According to S26KL512S datasheet [1] and S29GL01GS datasheet [2],
the procedure to read out PPB lock bits is to send the PPB Entry,
PPB Read, Reset/ASO Exit. Currently, the code does send incorrect
PPB Entry, PPB Read and Reset/ASO Exit is completely missing.
The PPB Entry sent is implemented by sending flash_unlock_seq()
and flash_write_cmd(..., FLASH_CMD_READ_ID). This translates to
sequence 0x555:0xaa, 0x2aa:0x55, 0x555:0x90=FLASH_CMD_READ_ID.
However, both [1] and [2] specify the last byte of PPB Entry as
0xc0=AMD_CMD_SET_PPB_ENTRY instead of 0x90=FLASH_CMD_READ_ID,
that is 0x555:0xaa, 0x2aa:0x55, 0x555:0xc0=AMD_CMD_SET_PPB_ENTRY.
Since this does make sense, this patch fixes it and thus also
aligns the code in flash_get_size() with flash_real_protect().
The PPB Read returns 00h in case of Protected state and 01h in case
of Unprotected state, according to [1] Note 83 and [2] Note 17, so
invert the result. Moreover, align the arguments with similar code
in flash_real_protect().
Finally, Reset/ASO Exit command should be executed to exit the PPB
mode, so add the missing reset.
[1] https://www.cypress.com/file/213346/download
Document Number: 001-99198 Rev. *M
Table 40. Command Definitions, Nonvolatile Sector Protection
Command Set Definitions
[2] https://www.cypress.com/file/177976/download
Document Number: 001-98285 Rev. *R
Table 7.1 Command Definitions, Nonvolatile Sector Protection
Command Set Definitions
Fixes: 03deff433e ("cfi_flash: Read PPB sector protection from device for
AMD/Spansion chips")
Signed-off-by: Marek Vasut <marek.vasut+rene...@gmail.com>
Cc: Stefan Roese <s...@denx.de>
Applied to u-boot-cfi-flash/master
Thanks,
Stefan
---
drivers/mtd/cfi_flash.c | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/drivers/mtd/cfi_flash.c b/drivers/mtd/cfi_flash.c
index 9642d7c7dc..9c27fea5d8 100644
--- a/drivers/mtd/cfi_flash.c
+++ b/drivers/mtd/cfi_flash.c
@@ -2276,12 +2276,12 @@ ulong flash_get_size(phys_addr_t base, int banknum)
flash_unlock_seq(info, 0);
flash_write_cmd(info, 0,
info->addr_unlock1,
- FLASH_CMD_READ_ID);
+ AMD_CMD_SET_PPB_ENTRY);
info->protect[sect_cnt] =
- flash_isset(
- info, sect_cnt,
- FLASH_OFFSET_PROTECT,
- FLASH_STATUS_PROTECT);
+ !flash_isset(info, sect_cnt,
+ 0, 0x01);
+ flash_write_cmd(info, 0, 0,
+ info->cmd_reset);
break;
default:
/* default: not protected */
Viele Grüße,
Stefan
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: s...@denx.de
