This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8568 platform, remove that support as well.
Cc: Priyanka Jain <priyanka.j...@nxp.com>
Signed-off-by: Tom Rini <tr...@konsulko.com>
---
arch/powerpc/cpu/mpc85xx/Kconfig | 21 +-
arch/powerpc/cpu/mpc85xx/Makefile | 1 -
arch/powerpc/cpu/mpc85xx/mpc8568_serdes.c | 58 ----
arch/powerpc/include/asm/config_mpc85xx.h | 10 -
arch/powerpc/include/asm/immap_85xx.h | 6 +-
board/freescale/mpc8568mds/Kconfig | 12 -
board/freescale/mpc8568mds/MAINTAINERS | 6 -
board/freescale/mpc8568mds/Makefile | 11 -
board/freescale/mpc8568mds/bcsr.c | 61 ----
board/freescale/mpc8568mds/bcsr.h | 92 -----
board/freescale/mpc8568mds/ddr.c | 53 ---
board/freescale/mpc8568mds/law.c | 40 ---
board/freescale/mpc8568mds/mpc8568mds.c | 359 -------------------
board/freescale/mpc8568mds/tlb.c | 83 -----
configs/MPC8568MDS_defconfig | 42 ---
include/configs/MPC8568MDS.h | 400 ----------------------
16 files changed, 3 insertions(+), 1252 deletions(-)
delete mode 100644 arch/powerpc/cpu/mpc85xx/mpc8568_serdes.c
delete mode 100644 board/freescale/mpc8568mds/Kconfig
delete mode 100644 board/freescale/mpc8568mds/MAINTAINERS
delete mode 100644 board/freescale/mpc8568mds/Makefile
delete mode 100644 board/freescale/mpc8568mds/bcsr.c
delete mode 100644 board/freescale/mpc8568mds/bcsr.h
delete mode 100644 board/freescale/mpc8568mds/ddr.c
delete mode 100644 board/freescale/mpc8568mds/law.c
delete mode 100644 board/freescale/mpc8568mds/mpc8568mds.c
delete mode 100644 board/freescale/mpc8568mds/tlb.c
delete mode 100644 configs/MPC8568MDS_defconfig
delete mode 100644 include/configs/MPC8568MDS.h
diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig
index 0a2921ddb323..cd7aa953567b 100644
--- a/arch/powerpc/cpu/mpc85xx/Kconfig
+++ b/arch/powerpc/cpu/mpc85xx/Kconfig
@@ -49,10 +49,6 @@ config TARGET_MPC8548CDS
select ARCH_MPC8548
select FSL_VIA
-config TARGET_MPC8568MDS
- bool "Support MPC8568MDS"
- select ARCH_MPC8568
-
config TARGET_P1010RDB_PA
bool "Support P1010RDB_PA"
select ARCH_P1010
@@ -378,15 +374,6 @@ config ARCH_MPC8560
select FSL_LAW
select SYS_FSL_HAS_DDR1
-config ARCH_MPC8568
- bool
- select FSL_LAW
- select FSL_PCIE_RESET
- select SYS_FSL_HAS_DDR2
- select SYS_FSL_HAS_SEC
- select SYS_FSL_SEC_BE
- select SYS_FSL_SEC_COMPAT_2
-
config ARCH_MPC8572
bool
select FSL_LAW
@@ -904,7 +891,6 @@ config SYS_CCSRBAR_DEFAULT
ARCH_MPC8544 || \
ARCH_MPC8548 || \
ARCH_MPC8560 || \
- ARCH_MPC8568 || \
ARCH_MPC8572 || \
ARCH_P1010 || \
ARCH_P1011 || \
@@ -1128,8 +1114,7 @@ config SYS_FSL_NUM_LAWS
ARCH_P1025 || \
ARCH_P2020
default 10 if ARCH_MPC8544 || \
- ARCH_MPC8548 || \
- ARCH_MPC8568
+ ARCH_MPC8548
default 8 if ARCH_MPC8540 || \
ARCH_MPC8560
help
@@ -1203,8 +1188,7 @@ config SYS_FSL_LBC_CLK_DIV
int "Divider of platform clock"
depends on FSL_ELBC || ARCH_MPC8540 || \
ARCH_MPC8548 || \
- ARCH_MPC8560 || \
- ARCH_MPC8568
+ ARCH_MPC8560
default 2 if ARCH_P2041 || \
ARCH_P3041 || \
@@ -1222,7 +1206,6 @@ config FSL_VIA
source "board/emulation/qemu-ppce500/Kconfig"
source "board/freescale/corenet_ds/Kconfig"
source "board/freescale/mpc8548cds/Kconfig"
-source "board/freescale/mpc8568mds/Kconfig"
source "board/freescale/p1010rdb/Kconfig"
source "board/freescale/p1_p2_rdb_pc/Kconfig"
source "board/freescale/p2041rdb/Kconfig"
diff --git a/arch/powerpc/cpu/mpc85xx/Makefile
b/arch/powerpc/cpu/mpc85xx/Makefile
index 4d9a07b5d9c3..8cd4b44ec5f9 100644
--- a/arch/powerpc/cpu/mpc85xx/Makefile
+++ b/arch/powerpc/cpu/mpc85xx/Makefile
@@ -61,7 +61,6 @@ obj-$(CONFIG_ARCH_C29X) += c29x_serdes.o
obj-$(CONFIG_ARCH_MPC8536) += mpc8536_serdes.o
obj-$(CONFIG_ARCH_MPC8544) += mpc8544_serdes.o
obj-$(CONFIG_ARCH_MPC8548) += mpc8548_serdes.o
-obj-$(CONFIG_ARCH_MPC8568) += mpc8568_serdes.o
obj-$(CONFIG_ARCH_MPC8572) += mpc8572_serdes.o
obj-$(CONFIG_ARCH_P1010) += p1010_serdes.o
obj-$(CONFIG_ARCH_P1011) += p1021_serdes.o
diff --git a/arch/powerpc/cpu/mpc85xx/mpc8568_serdes.c
b/arch/powerpc/cpu/mpc85xx/mpc8568_serdes.c
deleted file mode 100644
index 81b66c3fa6a2..000000000000
--- a/arch/powerpc/cpu/mpc85xx/mpc8568_serdes.c
+++ /dev/null
@@ -1,58 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2010 Freescale Semiconductor, Inc.
- */
-
-#include <config.h>
-#include <common.h>
-#include <log.h>
-#include <asm/io.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_serdes.h>
-
-#define SRDS1_MAX_LANES 8
-
-static u32 serdes1_prtcl_map;
-
-static u8 serdes1_cfg_tbl[][SRDS1_MAX_LANES] = {
- [0x3] = {PCIE1, PCIE1, PCIE1, PCIE1, SRIO1, SRIO1, SRIO1, SRIO1},
- [0x4] = {PCIE1, PCIE1, PCIE1, PCIE1, SRIO1, SRIO1, SRIO1, SRIO1},
- [0x5] = {NONE, NONE, NONE, NONE, SRIO1, SRIO1, SRIO1, SRIO1},
- [0x6] = {NONE, NONE, NONE, NONE, SRIO1, SRIO1, SRIO1, SRIO1},
- [0x7] = {PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1},
-};
-
-int is_serdes_configured(enum srds_prtcl prtcl)
-{
- if (!(serdes1_prtcl_map & (1 << NONE)))
- fsl_serdes_init();
-
- return (1 << prtcl) & serdes1_prtcl_map;
-}
-
-void fsl_serdes_init(void)
-{
- ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 pordevsr = in_be32(&gur->pordevsr);
- u32 srds_cfg = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >>
- MPC85xx_PORDEVSR_IO_SEL_SHIFT;
- int lane;
-
- if (serdes1_prtcl_map & (1 << NONE))
- return;
-
- debug("PORDEVSR[IO_SEL_SRDS] = %x\n", srds_cfg);
-
- if (srds_cfg >= ARRAY_SIZE(serdes1_cfg_tbl)) {
- printf("Invalid PORDEVSR[IO_SEL_SRDS] = %d\n", srds_cfg);
- return;
- }
-
- for (lane = 0; lane < SRDS1_MAX_LANES; lane++) {
- enum srds_prtcl lane_prtcl = serdes1_cfg_tbl[srds_cfg][lane];
- serdes1_prtcl_map |= (1 << lane_prtcl);
- }
-
- /* Set the first bit to indicate serdes has been initialized */
- serdes1_prtcl_map |= (1 << NONE);
-}
diff --git a/arch/powerpc/include/asm/config_mpc85xx.h
b/arch/powerpc/include/asm/config_mpc85xx.h
index a52b31ec3950..33a3b3a13db7 100644
--- a/arch/powerpc/include/asm/config_mpc85xx.h
+++ b/arch/powerpc/include/asm/config_mpc85xx.h
@@ -28,16 +28,6 @@
#define CONFIG_SYS_FSL_RMU
#define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2
-#elif defined(CONFIG_ARCH_MPC8568)
-#define QE_MURAM_SIZE 0x10000UL
-#define MAX_QE_RISC 2
-#define QE_NUM_OF_SNUM 28
-#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 1
-#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
-#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
-#define CONFIG_SYS_FSL_RMU
-#define CONFIG_SYS_FSL_SRIO_MSG_UNIT_NUM 2
-
#elif defined(CONFIG_ARCH_P1010)
#define CONFIG_FSL_SDHC_V2_3
#define CONFIG_TSECV2
diff --git a/arch/powerpc/include/asm/immap_85xx.h
b/arch/powerpc/include/asm/immap_85xx.h
index bb6a684d5b05..900b8f43c82e 100644
--- a/arch/powerpc/include/asm/immap_85xx.h
+++ b/arch/powerpc/include/asm/immap_85xx.h
@@ -2457,11 +2457,7 @@ typedef struct ccsr_gur {
u32 svr; /* System version */
u8 res10[8];
u32 rstcr; /* Reset control */
-#if defined(CONFIG_ARCH_MPC8568)
- u8 res11a[76];
- par_io_t qe_par_io[7];
- u8 res11b[1600];
-#elif defined(CONFIG_ARCH_P1021) || defined(CONFIG_ARCH_P1025)
+#if defined(CONFIG_ARCH_P1021) || defined(CONFIG_ARCH_P1025)
u8 res11a[12];
u32 iovselsr;
u8 res11b[60];
diff --git a/board/freescale/mpc8568mds/Kconfig
b/board/freescale/mpc8568mds/Kconfig
deleted file mode 100644
index 4e178c503968..000000000000
--- a/board/freescale/mpc8568mds/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_MPC8568MDS
-
-config SYS_BOARD
- default "mpc8568mds"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_CONFIG_NAME
- default "MPC8568MDS"
-
-endif
diff --git a/board/freescale/mpc8568mds/MAINTAINERS
b/board/freescale/mpc8568mds/MAINTAINERS
deleted file mode 100644
index f4747866d2bd..000000000000
--- a/board/freescale/mpc8568mds/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-MPC8568MDS BOARD
-M: Priyanka Jain <priyanka.j...@nxp.com>
-S: Maintained
-F: board/freescale/mpc8568mds/
-F: include/configs/MPC8568MDS.h
-F: configs/MPC8568MDS_defconfig
diff --git a/board/freescale/mpc8568mds/Makefile
b/board/freescale/mpc8568mds/Makefile
deleted file mode 100644
index 1e9095bdddd6..000000000000
--- a/board/freescale/mpc8568mds/Makefile
+++ /dev/null
@@ -1,11 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright 2004-2007 Freescale Semiconductor.
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, w...@denx.de.
-
-obj-y += mpc8568mds.o
-obj-y += bcsr.o
-obj-y += ddr.o
-obj-y += law.o
-obj-y += tlb.o
diff --git a/board/freescale/mpc8568mds/bcsr.c
b/board/freescale/mpc8568mds/bcsr.c
deleted file mode 100644
index b1e638af5aec..000000000000
--- a/board/freescale/mpc8568mds/bcsr.c
+++ /dev/null
@@ -1,61 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2007 Freescale Semiconductor.
- */
-
-#include <common.h>
-#include <flash.h>
-#include <asm/io.h>
-
-#include "bcsr.h"
-
-void enable_8568mds_duart(void)
-{
- volatile uint* duart_mux = (uint *)(CONFIG_SYS_CCSRBAR +
0xe0060);
- volatile uint* devices = (uint *)(CONFIG_SYS_CCSRBAR +
0xe0070);
- volatile u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR);
-
- *duart_mux = 0x80000000; /* Set the mux to Duart on PMUXCR */
- *devices = 0; /* Enable all peripheral devices */
- bcsr[5] |= 0x01; /* Enable Duart in BCSR*/
-}
-
-void enable_8568mds_flash_write(void)
-{
- volatile u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR);
-
- bcsr[9] |= 0x01;
-}
-
-void disable_8568mds_flash_write(void)
-{
- volatile u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR);
-
- bcsr[9] &= ~(0x01);
-}
-
-void enable_8568mds_qe_mdio(void)
-{
- u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR);
-
- bcsr[7] |= 0x01;
-}
-
-#if defined(CONFIG_UEC_ETH1) || defined(CONFIG_UEC_ETH2)
-void reset_8568mds_uccs(void)
-{
- volatile u8 *bcsr = (u8 *)(CONFIG_SYS_BCSR);
-
- /* Turn off UCC1 & UCC2 */
- out_8(&bcsr[8], in_8(&bcsr[8]) & ~BCSR_UCC1_GETH_EN);
- out_8(&bcsr[9], in_8(&bcsr[9]) & ~BCSR_UCC2_GETH_EN);
-
- /* Mode is RGMII, all bits clear */
- out_8(&bcsr[11], in_8(&bcsr[11]) & ~(BCSR_UCC1_MODE_MSK |
- BCSR_UCC2_MODE_MSK));
-
- /* Turn UCC1 & UCC2 on */
- out_8(&bcsr[8], in_8(&bcsr[8]) | BCSR_UCC1_GETH_EN);
- out_8(&bcsr[9], in_8(&bcsr[9]) | BCSR_UCC2_GETH_EN);
-}
-#endif
diff --git a/board/freescale/mpc8568mds/bcsr.h
b/board/freescale/mpc8568mds/bcsr.h
deleted file mode 100644
index a8e13a2a5577..000000000000
--- a/board/freescale/mpc8568mds/bcsr.h
+++ /dev/null
@@ -1,92 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2007 Freescale Semiconductor.
- */
-
-#ifndef __BCSR_H_
-#define __BCSR_H_
-
-#include <common.h>
-
-/* BCSR Bit definitions
- * BCSR 0 *
- 0:3 ccb sys pll
- 4:6 cfg core pll
- 7 cfg boot seq
-
- * BCSR 1 *
- 0:2 cfg rom lock
- 3:5 cfg host agent
- 6 PCI IO
- 7 cfg RIO size
-
- * BCSR 2 *
- 0:4 QE PLL
- 5 QE clock
- 6 cfg PCI arbiter
-
- * BCSR 3 *
- 0 TSEC1 reduce
- 1 TSEC2 reduce
- 2:3 TSEC1 protocol
- 4:5 TSEC2 protocol
- 6 PHY1 slave
- 7 PHY2 slave
-
- * BCSR 4 *
- 4 clock enable
- 5 boot EPROM
- 6 GETH transactive reset
- 7 BRD write potect
-
- * BCSR 5 *
- 1:3 Leds 1-3
- 4 UPC1 enable
- 5 UPC2 enable
- 6 UPC2 pos
- 7 RS232 enable
-
- * BCSR 6 *
- 0 CFG ver 0
- 1 CFG ver 1
- 6 Register config led
- 7 Power on reset
-
- * BCSR 7 *
- 2 board host mode indication
- 5 enable TSEC1 PHY
- 6 enable TSEC2 PHY
-
- * BCSR 8 *
- 0 UCC GETH1 enable
- 1 UCC GMII enable
- 3 UCC TBI enable
- 5 UCC MII enable
- 7 Real time clock reset
-
- * BCSR 9 *
- 0 UCC2 GETH enable
- 1 UCC2 GMII enable
- 3 UCC2 TBI enable
- 5 UCC2 MII enable
- 6 Ready only - indicate flash ready after burning
- 7 Flash write protect
-*/
-
-#define BCSR_UCC1_GETH_EN (0x1 << 7)
-#define BCSR_UCC2_GETH_EN (0x1 << 7)
-#define BCSR_UCC1_MODE_MSK (0x3 << 4)
-#define BCSR_UCC2_MODE_MSK (0x3 << 0)
-
-/*BCSR Utils functions*/
-
-void enable_8568mds_duart(void);
-void enable_8568mds_flash_write(void);
-void disable_8568mds_flash_write(void);
-void enable_8568mds_qe_mdio(void);
-
-#if defined(CONFIG_UEC_ETH1) || defined(CONFIG_UEC_ETH2)
-void reset_8568mds_uccs(void);
-#endif
-
-#endif /* __BCSR_H_ */
diff --git a/board/freescale/mpc8568mds/ddr.c b/board/freescale/mpc8568mds/ddr.c
deleted file mode 100644
index 58a979dbc76c..000000000000
--- a/board/freescale/mpc8568mds/ddr.c
+++ /dev/null
@@ -1,53 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-
-void fsl_ddr_board_options(memctl_options_t *popts,
- dimm_params_t *pdimm,
- unsigned int ctrl_num)
-{
- /*
- * Factors to consider for clock adjust:
- * - number of chips on bus
- * - position of slot
- * - DDR1 vs. DDR2?
- * - ???
- *
- * This needs to be determined on a board-by-board basis.
- * 0110 3/4 cycle late
- * 0111 7/8 cycle late
- */
- popts->clk_adjust = 6;
-
- /*
- * Factors to consider for CPO:
- * - frequency
- * - ddr1 vs. ddr2
- */
- popts->cpo_override = 10;
-
- /*
- * Factors to consider for write data delay:
- * - number of DIMMs
- *
- * 1 = 1/4 clock delay
- * 2 = 1/2 clock delay
- * 3 = 3/4 clock delay
- * 4 = 1 clock delay
- * 5 = 5/4 clock delay
- * 6 = 3/2 clock delay
- */
- popts->write_data_delay = 3;
-
- /*
- * Factors to consider for half-strength driver enable:
- * - number of DIMMs installed
- */
- popts->half_strength_driver_enable = 0;
-}
diff --git a/board/freescale/mpc8568mds/law.c b/board/freescale/mpc8568mds/law.c
deleted file mode 100644
index c04c36b5d82c..000000000000
--- a/board/freescale/mpc8568mds/law.c
+++ /dev/null
@@ -1,40 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008, 2010-2011 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, w...@denx.de.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-/*
- * LAW(Local Access Window) configuration:
- *
- *0) 0x0000_0000 0x7fff_ffff DDR 2G
- *1) 0x8000_0000 0x9fff_ffff PCI1 MEM 512MB
- *2) 0xa000_0000 0xbfff_ffff PCIe MEM 512MB
- *-) 0xe000_0000 0xe00f_ffff CCSR 1M
- *3) 0xe200_0000 0xe27f_ffff PCI1 I/O 8M
- *4) 0xe280_0000 0xe2ff_ffff PCIe I/O 8M
- *5) 0xc000_0000 0xdfff_ffff SRIO 512MB
- *6.a) 0xf000_0000 0xf3ff_ffff SDRAM 64MB
- *6.b) 0xf800_0000 0xf800_7fff BCSR 32KB
- *6.c) 0xf800_8000 0xf800_ffff PIB (CS4) 32KB
- *6.d) 0xf801_0000 0xf801_7fff PIB (CS5) 32KB
- *6.e) 0xfe00_0000 0xffff_ffff Flash 32MB
- *
- *Notes:
- * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
- * If flash is 8M at default position (last 8M), no LAW needed.
- *
- */
-
-struct law_entry law_table[] = {
- /* LBC window - maps 256M. That's SDRAM, BCSR, PIBs, and Flash */
- SET_LAW(CONFIG_SYS_LBC_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/mpc8568mds/mpc8568mds.c
b/board/freescale/mpc8568mds/mpc8568mds.c
deleted file mode 100644
index 7b379464cd59..000000000000
--- a/board/freescale/mpc8568mds/mpc8568mds.c
+++ /dev/null
@@ -1,359 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2007,2009-2011 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2002 Scott McNutt <smcn...@artesyncp.com>
- */
-
-#include <common.h>
-#include <flash.h>
-#include <init.h>
-#include <log.h>
-#include <pci.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_pci.h>
-#include <fsl_ddr_sdram.h>
-#include <asm/fsl_serdes.h>
-#include <spd_sdram.h>
-#include <i2c.h>
-#include <ioports.h>
-#include <linux/delay.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-
-#include "bcsr.h"
-
-const qe_iop_conf_t qe_iop_conf_tab[] = {
- /* GETH1 */
- {4, 10, 1, 0, 2}, /* TxD0 */
- {4, 9, 1, 0, 2}, /* TxD1 */
- {4, 8, 1, 0, 2}, /* TxD2 */
- {4, 7, 1, 0, 2}, /* TxD3 */
- {4, 23, 1, 0, 2}, /* TxD4 */
- {4, 22, 1, 0, 2}, /* TxD5 */
- {4, 21, 1, 0, 2}, /* TxD6 */
- {4, 20, 1, 0, 2}, /* TxD7 */
- {4, 15, 2, 0, 2}, /* RxD0 */
- {4, 14, 2, 0, 2}, /* RxD1 */
- {4, 13, 2, 0, 2}, /* RxD2 */
- {4, 12, 2, 0, 2}, /* RxD3 */
- {4, 29, 2, 0, 2}, /* RxD4 */
- {4, 28, 2, 0, 2}, /* RxD5 */
- {4, 27, 2, 0, 2}, /* RxD6 */
- {4, 26, 2, 0, 2}, /* RxD7 */
- {4, 11, 1, 0, 2}, /* TX_EN */
- {4, 24, 1, 0, 2}, /* TX_ER */
- {4, 16, 2, 0, 2}, /* RX_DV */
- {4, 30, 2, 0, 2}, /* RX_ER */
- {4, 17, 2, 0, 2}, /* RX_CLK */
- {4, 19, 1, 0, 2}, /* GTX_CLK */
- {1, 31, 2, 0, 3}, /* GTX125 */
-
- /* GETH2 */
- {5, 10, 1, 0, 2}, /* TxD0 */
- {5, 9, 1, 0, 2}, /* TxD1 */
- {5, 8, 1, 0, 2}, /* TxD2 */
- {5, 7, 1, 0, 2}, /* TxD3 */
- {5, 23, 1, 0, 2}, /* TxD4 */
- {5, 22, 1, 0, 2}, /* TxD5 */
- {5, 21, 1, 0, 2}, /* TxD6 */
- {5, 20, 1, 0, 2}, /* TxD7 */
- {5, 15, 2, 0, 2}, /* RxD0 */
- {5, 14, 2, 0, 2}, /* RxD1 */
- {5, 13, 2, 0, 2}, /* RxD2 */
- {5, 12, 2, 0, 2}, /* RxD3 */
- {5, 29, 2, 0, 2}, /* RxD4 */
- {5, 28, 2, 0, 2}, /* RxD5 */
- {5, 27, 2, 0, 3}, /* RxD6 */
- {5, 26, 2, 0, 2}, /* RxD7 */
- {5, 11, 1, 0, 2}, /* TX_EN */
- {5, 24, 1, 0, 2}, /* TX_ER */
- {5, 16, 2, 0, 2}, /* RX_DV */
- {5, 30, 2, 0, 2}, /* RX_ER */
- {5, 17, 2, 0, 2}, /* RX_CLK */
- {5, 19, 1, 0, 2}, /* GTX_CLK */
- {1, 31, 2, 0, 3}, /* GTX125 */
- {4, 6, 3, 0, 2}, /* MDIO */
- {4, 5, 1, 0, 2}, /* MDC */
-
- /* UART1 */
- {2, 0, 1, 0, 2}, /* UART_SOUT1 */
- {2, 1, 1, 0, 2}, /* UART_RTS1 */
- {2, 2, 2, 0, 2}, /* UART_CTS1 */
- {2, 3, 2, 0, 2}, /* UART_SIN1 */
-
- {0, 0, 0, 0, QE_IOP_TAB_END}, /* END of table */
-};
-
-void local_bus_init(void);
-
-int board_early_init_f (void)
-{
- /*
- * Initialize local bus.
- */
- local_bus_init ();
-
- enable_8568mds_duart();
- enable_8568mds_flash_write();
-#if defined(CONFIG_UEC_ETH1) || defined(CONFIG_UEC_ETH2)
- reset_8568mds_uccs();
-#endif
-#if defined(CONFIG_QE) && !defined(CONFIG_eTSEC_MDIO_BUS)
- enable_8568mds_qe_mdio();
-#endif
-
-#ifdef CONFIG_SYS_I2C2_OFFSET
- /* Enable I2C2_SCL and I2C2_SDA */
- volatile struct par_io *port_c;
- port_c = (struct par_io*)(CONFIG_SYS_IMMR + 0xe0140);
- port_c->cpdir2 |= 0x0f000000;
- port_c->cppar2 &= ~0x0f000000;
- port_c->cppar2 |= 0x0a000000;
-#endif
-
- return 0;
-}
-
-int checkboard (void)
-{
- printf ("Board: 8568 MDS\n");
-
- return 0;
-}
-
-/*
- * Initialize Local Bus
- */
-void
-local_bus_init(void)
-{
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
-
- uint clkdiv;
- sys_info_t sysinfo;
-
- get_sys_info(&sysinfo);
- clkdiv = (lbc->lcrr & LCRR_CLKDIV) * 2;
-
- gur->lbiuiplldcr1 = 0x00078080;
- if (clkdiv == 16) {
- gur->lbiuiplldcr0 = 0x7c0f1bf0;
- } else if (clkdiv == 8) {
- gur->lbiuiplldcr0 = 0x6c0f1bf0;
- } else if (clkdiv == 4) {
- gur->lbiuiplldcr0 = 0x5c0f1bf0;
- }
-
- lbc->lcrr |= 0x00030000;
-
- asm("sync;isync;msync");
-}
-
-/*
- * Initialize SDRAM memory on the Local Bus.
- */
-void lbc_sdram_init(void)
-{
-#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM)
-
- uint idx;
- volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
- uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
- uint lsdmr_common;
-
- puts("LBC SDRAM: ");
- print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024,
- "\n ");
-
- /*
- * Setup SDRAM Base and Option Registers
- */
- set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
- set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
- asm("msync");
-
- lbc->lbcr = CONFIG_SYS_LBC_LBCR;
- asm("msync");
-
- lbc->lsrt = CONFIG_SYS_LBC_LSRT;
- lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
- asm("msync");
-
- /*
- * MPC8568 uses "new" 15-16 style addressing.
- */
- lsdmr_common = CONFIG_SYS_LBC_LSDMR_COMMON;
- lsdmr_common |= LSDMR_BSMA1516;
-
- /*
- * Issue PRECHARGE ALL command.
- */
- lbc->lsdmr = lsdmr_common | LSDMR_OP_PCHALL;
- asm("sync;msync");
- *sdram_addr = 0xff;
- ppcDcbf((unsigned long) sdram_addr);
- udelay(100);
-
- /*
- * Issue 8 AUTO REFRESH commands.
- */
- for (idx = 0; idx < 8; idx++) {
- lbc->lsdmr = lsdmr_common | LSDMR_OP_ARFRSH;
- asm("sync;msync");
- *sdram_addr = 0xff;
- ppcDcbf((unsigned long) sdram_addr);
- udelay(100);
- }
-
- /*
- * Issue 8 MODE-set command.
- */
- lbc->lsdmr = lsdmr_common | LSDMR_OP_MRW;
- asm("sync;msync");
- *sdram_addr = 0xff;
- ppcDcbf((unsigned long) sdram_addr);
- udelay(100);
-
- /*
- * Issue NORMAL OP command.
- */
- lbc->lsdmr = lsdmr_common | LSDMR_OP_NORMAL;
- asm("sync;msync");
- *sdram_addr = 0xff;
- ppcDcbf((unsigned long) sdram_addr);
- udelay(200); /* Overkill. Must wait > 200 bus cycles */
-
-#endif /* enable SDRAM init */
-}
-
-#if defined(CONFIG_PCI)
-#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_mpc8568mds_config_table[] = {
- {
- PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
- pci_cfgfunc_config_device,
- {PCI_ENET0_IOADDR,
- PCI_ENET0_MEMADDR,
- PCI_COMMON_MEMORY | PCI_COMMAND_MASTER}
- },
- {}
-};
-#endif
-
-static struct pci_controller pci1_hose;
-#endif /* CONFIG_PCI */
-
-/*
- * pib_init() -- Initialize the PCA9555 IO expander on the PIB board
- */
-void
-pib_init(void)
-{
- u8 val8, orig_i2c_bus;
- /*
- * Assign PIB PMC2/3 to PCI bus
- */
-
- /*switch temporarily to I2C bus #2 */
- orig_i2c_bus = i2c_get_bus_num();
- i2c_set_bus_num(1);
-
- val8 = 0x00;
- i2c_write(0x23, 0x6, 1, &val8, 1);
- i2c_write(0x23, 0x7, 1, &val8, 1);
- val8 = 0xff;
- i2c_write(0x23, 0x2, 1, &val8, 1);
- i2c_write(0x23, 0x3, 1, &val8, 1);
-
- val8 = 0x00;
- i2c_write(0x26, 0x6, 1, &val8, 1);
- val8 = 0x34;
- i2c_write(0x26, 0x7, 1, &val8, 1);
- val8 = 0xf9;
- i2c_write(0x26, 0x2, 1, &val8, 1);
- val8 = 0xff;
- i2c_write(0x26, 0x3, 1, &val8, 1);
-
- val8 = 0x00;
- i2c_write(0x27, 0x6, 1, &val8, 1);
- i2c_write(0x27, 0x7, 1, &val8, 1);
- val8 = 0xff;
- i2c_write(0x27, 0x2, 1, &val8, 1);
- val8 = 0xef;
- i2c_write(0x27, 0x3, 1, &val8, 1);
-
- asm("eieio");
- i2c_set_bus_num(orig_i2c_bus);
-}
-
-#ifdef CONFIG_PCI
-void pci_init_board(void)
-{
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- int first_free_busno = 0;
-#ifdef CONFIG_PCI1
- struct fsl_pci_info pci_info;
- u32 devdisr, pordevsr, io_sel;
- u32 porpllsr, pci_agent, pci_speed, pci_32, pci_arb, pci_clk_sel;
-
- devdisr = in_be32(&gur->devdisr);
- pordevsr = in_be32(&gur->pordevsr);
- porpllsr = in_be32(&gur->porpllsr);
- io_sel = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
-
- debug(" %s: devdisr=%x, io_sel=%x\n", __func__, devdisr, io_sel);
-
- pci_speed = 66666000;
- pci_32 = 1;
- pci_arb = pordevsr & MPC85xx_PORDEVSR_PCI1_ARB;
- pci_clk_sel = porpllsr & MPC85xx_PORDEVSR_PCI1_SPD;
-
- if (!(devdisr & MPC85xx_DEVDISR_PCI1)) {
- SET_STD_PCI_INFO(pci_info, 1);
- set_next_law(pci_info.mem_phys,
- law_size_bits(pci_info.mem_size), pci_info.law);
- set_next_law(pci_info.io_phys,
- law_size_bits(pci_info.io_size), pci_info.law);
-
- pci_agent = fsl_setup_hose(&pci1_hose, pci_info.regs);
- printf("PCI: %d bit, %s MHz, %s, %s, %s (base address %lx)\n",
- (pci_32) ? 32 : 64,
- (pci_speed == 33333000) ? "33" :
- (pci_speed == 66666000) ? "66" : "unknown",
- pci_clk_sel ? "sync" : "async",
- pci_agent ? "agent" : "host",
- pci_arb ? "arbiter" : "external-arbiter",
- pci_info.regs);
-
-#ifndef CONFIG_PCI_PNP
- pci1_hose.config_table = pci_mpc8568mds_config_table;
-#endif
- first_free_busno = fsl_pci_init_port(&pci_info,
- &pci1_hose, first_free_busno);
- } else {
- printf("PCI: disabled\n");
- }
-
- puts("\n");
-#else
- setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI1); /* disable */
-#endif
-
- fsl_pcie_init_board(first_free_busno);
-}
-#endif /* CONFIG_PCI */
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
- ft_cpu_setup(blob, bd);
-
- FT_FSL_PCI_SETUP;
-
- return 0;
-}
-#endif
diff --git a/board/freescale/mpc8568mds/tlb.c b/board/freescale/mpc8568mds/tlb.c
deleted file mode 100644
index fea1606a1d3f..000000000000
--- a/board/freescale/mpc8568mds/tlb.c
+++ /dev/null
@@ -1,83 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, w...@denx.de.
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 ,
CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 ,
CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 ,
CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
-
- /* TLB 1 Initializations */
- /*
- * TLBe 0: 16M Non-cacheable, guarded
- * 0xff000000 16M FLASH (upper half)
- * Out of reset this entry is only 4K.
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE + 0x1000000,
CONFIG_SYS_FLASH_BASE + 0x1000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_16M, 1),
-
- /*
- * TLBe 1: 16M Non-cacheable, guarded
- * 0xfe000000 16M FLASH (lower half)
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_16M, 1),
-
- /*
- * TLBe 2: 1G Non-cacheable, guarded
- * 0x80000000 512M PCI1 MEM
- * 0xa0000000 512M PCIe MEM
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_VIRT, CONFIG_SYS_PCI1_MEM_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 2, BOOKE_PAGESZ_1G, 1),
-
- /*
- * TLBe 3: 64M Non-cacheable, guarded
- * 0xe000_0000 1M CCSRBAR
- * 0xe200_0000 8M PCI1 IO
- * 0xe280_0000 8M PCIe IO
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 3, BOOKE_PAGESZ_64M, 1),
-
- /*
- * TLBe 4: 64M Cacheable, non-guarded
- * 0xf000_0000 64M LBC SDRAM
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_LBC_SDRAM_BASE, CONFIG_SYS_LBC_SDRAM_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
- 0, 4, BOOKE_PAGESZ_64M, 1),
-
- /*
- * TLBe 5: 256K Non-cacheable, guarded
- * 0xf8000000 32K BCSR
- * 0xf8008000 32K PIB (CS4)
- * 0xf8010000 32K PIB (CS5)
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 5, BOOKE_PAGESZ_256K, 1),
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/configs/MPC8568MDS_defconfig b/configs/MPC8568MDS_defconfig
deleted file mode 100644
index 106e1a274673..000000000000
--- a/configs/MPC8568MDS_defconfig
+++ /dev/null
@@ -1,42 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xfff80000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_MPC85xx=y
-# CONFIG_CMD_ERRATA is not set
-CONFIG_TARGET_MPC8568MDS=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-CONFIG_BOARD_EARLY_INIT_F=y
-# CONFIG_MISC_INIT_R is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_REGINFO=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-# CONFIG_CMD_HASH is not set
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_ENV_ADDR=0xFFF60000
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_QE=y
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
deleted file mode 100644
index 2c43981a1cc7..000000000000
--- a/include/configs/MPC8568MDS.h
+++ /dev/null
@@ -1,400 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2004-2007, 2010-2011 Freescale Semiconductor.
- */
-
-/*
- * mpc8568mds board configuration file
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_SYS_SRIO
-#define CONFIG_SRIO1 /* SRIO port 1 */
-
-#define CONFIG_PCI1 1 /* PCI controller */
-#define CONFIG_PCIE1 1 /* PCIE controller */
-#define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_clock_freq(void);
-#endif /*Replace a call to
get_clock_freq (after it is implemented)*/
-#define CONFIG_SYS_CLK_FREQ 66000000 /*TODO: restore if wanting to read
from BCSR: get_clock_freq()*/ /* sysclk for MPC85xx */
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache
*/
-#define CONFIG_BTB /* toggle branch predition */
-
-/*
- * Only possible on E500 Version 2 or newer cores.
- */
-#define CONFIG_ENABLE_36BIT_PHYS 1
-
-#define CONFIG_SYS_CCSRBAR 0xe0000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-
-/* DDR Setup */
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_SPD
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
-
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system
memory*/
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
-/* I2C addresses of SPD EEPROMs */
-#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
-
-/* Make sure required options are set */
-#ifndef CONFIG_SPD_EEPROM
-#error ("CONFIG_SPD_EEPROM is required")
-#endif
-
-/*
- * Local Bus Definitions
- */
-
-/*
- * FLASH on the Local Bus
- * Two banks, 8M each, using the CFI driver.
- * Boot from BR0/OR0 bank at 0xff00_0000
- * Alternate BR1/OR1 bank at 0xff80_0000
- *
- * BR0, BR1:
- * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
- * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
- * Port Size = 16 bits = BRx[19:20] = 10
- * Use GPCM = BRx[24:26] = 000
- * Valid = BRx[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0
- * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1
- *
- * OR0, OR1:
- * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
- * Reserved ORx[17:18] = 11, confusion here?
- * CSNT = ORx[20] = 1
- * ACS = half cycle delay = ORx[21:22] = 11
- * SCY = 6 = ORx[24:27] = 0110
- * TRLX = use relaxed timing = ORx[29] = 1
- * EAD = use external address latch delay = OR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx
- */
-#define CONFIG_SYS_BCSR_BASE 0xf8000000
-
-#define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of FLASH 32M */
-
-/*Chip select 0 - Flash*/
-#define CONFIG_SYS_BR0_PRELIM 0xfe001001
-#define CONFIG_SYS_OR0_PRELIM 0xfe006ff7
-
-/*Chip slelect 1 - BCSR*/
-#define CONFIG_SYS_BR1_PRELIM 0xf8000801
-#define CONFIG_SYS_OR1_PRELIM 0xffffe9f7
-
-/*#define CONFIG_SYS_FLASH_BANKS_LIST {0xff800000, CONFIG_SYS_FLASH_BASE} */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of
banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per
device */
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout
(ms) */
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of
monitor */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-/*
- * SDRAM on the LocalBus
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM
*/
-#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is
64MB */
-
-/*Chip select 2 - SDRAM*/
-#define CONFIG_SYS_BR2_PRELIM 0xf0001861
-#define CONFIG_SYS_OR2_PRELIM 0xfc006901
-
-#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
-#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
-#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh
timer */
-#define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer
prescal*/
-
-/*
- * Common settings for all Local Bus SDRAM commands.
- * At run time, either BSMA1516 (for CPU 1.1)
- * or BSMA1617 (for CPU 1.0) (old)
- * is OR'ed in too.
- */
-#define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \
- | LSDMR_PRETOACT7 \
- | LSDMR_ACTTORW7 \
- | LSDMR_BL8 \
- | LSDMR_WRC4 \
- | LSDMR_CL3 \
- | LSDMR_RFEN \
- )
-
-/*
- * The bcsr registers are connected to CS3 on MDS.
- * The new memory map places bcsr at 0xf8000000.
- *
- * For BR3, need:
- * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
- * port-size = 8-bits = BR[19:20] = 01
- * no parity checking = BR[21:22] = 00
- * GPMC for MSEL = BR[24:26] = 000
- * Valid = BR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
- *
- * For OR3, need:
- * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0
- * disable buffer ctrl OR[19] = 0
- * CSNT OR[20] = 1
- * ACS OR[21:22] = 11
- * XACS OR[23] = 1
- * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe
- * SETA OR[28] = 0
- * TRLX OR[29] = 1
- * EHTR OR[30] = 1
- * EAD extra time OR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
- */
-#define CONFIG_SYS_BCSR (0xf8000000)
-
-/*Chip slelect 4 - PIB*/
-#define CONFIG_SYS_BR4_PRELIM 0xf8008801
-#define CONFIG_SYS_OR4_PRELIM 0xffffe9f7
-
-/*Chip select 5 - PIB*/
-#define CONFIG_SYS_BR5_PRELIM 0xf8010801
-#define CONFIG_SYS_OR5_PRELIM 0xffff69f7
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address
*/
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM
*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -
GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon
*/
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc
*/
-
-/* Serial Port */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
-
-/*
- * General PCI
- * Memory Addresses are mapped 1-1. I/O is mapped from 0
- */
-#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000
-#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000
-#define CONFIG_SYS_PCI1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 8M */
-
-#define CONFIG_SYS_PCIE1_NAME "Slot"
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
-
-#define CONFIG_SYS_SRIO1_MEM_VIRT 0xC0000000
-#define CONFIG_SYS_SRIO1_MEM_BUS 0xC0000000
-#define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_BUS
-#define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */
-
-#ifdef CONFIG_QE
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#ifndef CONFIG_TSEC_ENET
-#define CONFIG_ETHPRIME "UEC0"
-#endif
-#define CONFIG_PHY_MODE_NEED_CHANGE
-#define CONFIG_eTSEC_MDIO_BUS
-
-#ifdef CONFIG_eTSEC_MDIO_BUS
-#define CONFIG_MIIM_ADDRESS 0xE0024520
-#endif
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK16
-#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 7
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
-#endif
-
-#define CONFIG_UEC_ETH2 /* GETH2 */
-
-#ifdef CONFIG_UEC_ETH2
-#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */
-#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE
-#define CONFIG_SYS_UEC2_TX_CLK QE_CLK16
-#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH
-#define CONFIG_SYS_UEC2_PHY_ADDR 1
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
-#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
-#endif
-#endif /* CONFIG_QE */
-
-#if defined(CONFIG_PCI)
-
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-
-#endif /* CONFIG_PCI */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC0"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC1"
-
-#define TSEC1_PHY_ADDR 2
-#define TSEC2_PHY_ADDR 3
-
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-
-#define TSEC1_FLAGS TSEC_GIGABIT
-#define TSEC2_FLAGS TSEC_GIGABIT
-
-/* Options are: eTSEC[0-1] */
-#define CONFIG_ETHPRIME "eTSEC0"
-
-#endif /* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for
Linux*/
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-/* The mac addresses for all ethernet interface */
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#define CONFIG_HAS_ETH3
-#endif
-
-#define CONFIG_IPADDR 192.168.1.253
-
-#define CONFIG_HOSTNAME "unknown"
-#define CONFIG_ROOTPATH "/nfsroot"
-#define CONFIG_BOOTFILE "your.uImage"
-
-#define CONFIG_SERVERIP 192.168.1.1
-#define CONFIG_GATEWAYIP 192.168.1.1
-#define CONFIG_NETMASK 255.255.255.0
-
-#define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/
-
-#define CONFIG_EXTRA_ENV_SETTINGS
\
- "netdev=eth0\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=600000\0" \
- "ramdiskfile=your.ramdisk.u-boot\0" \
- "fdtaddr=400000\0" \
- "fdtfile=your.fdt.dtb\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs\0" \
- "ramargs=setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs\0" \
-
-#define CONFIG_NFSBOOTCOMMAND \
- "run nfsargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "run ramargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "bootm $loadaddr $ramdiskaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
-
-#endif /* __CONFIG_H */
--
2.17.1
