On 6/3/21 11:51 AM, Yangbo Lu wrote: > For eSDHC, power supply is through peripheral circuit. > Some eSDHC versions have value 0 of the bit but that > does not reflect the truth. 3.3V is common for SD/MMC, > and is supported for all boards with eSDHC in current > u-boot. So, make 3.3V is supported in default in code. > CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled if > future board does not support 3.3V. > > This is also a fix-up for one previous patch, which converted > to use IS_ENABLED() for CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 > that is not a Kconfig option. > > Fixes: 52faec31827e ("mmc: fsl_esdhc: replace most #ifdefs by IS_ENABLED()") > Signed-off-by: Yangbo Lu <yangbo...@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.ch...@samsung.com> Best Regards, Jaehoon Chung > --- > Changes for v2: > - Updated copyright. > Chagnes for v3: > - Fixed code logic. > --- > drivers/mmc/Kconfig | 7 +++++++ > drivers/mmc/fsl_esdhc.c | 17 ++++++++++++++--- > 2 files changed, 21 insertions(+), 3 deletions(-) > > diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig > index 8901456967..0909f502a1 100644 > --- a/drivers/mmc/Kconfig > +++ b/drivers/mmc/Kconfig > @@ -798,6 +798,13 @@ config FSL_ESDHC_33V_IO_RELIABILITY_WORKAROUND > This option assumes no hotplug, and u-boot has to make all the way to > to linux to use 1.8v UHS-I speed mode if has card. > > +config FSL_ESDHC_VS33_NOT_SUPPORT > + bool "3.3V power supply not supported" > + depends on FSL_ESDHC > + help > + For eSDHC, power supply is through peripheral circuit. 3.3V support is > + common. Select this if 3.3V power supply not supported. > + > config FSL_ESDHC_IMX > bool "Freescale/NXP i.MX eSDHC controller support" > help > diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c > index 7501fdb71e..1d98fa65c4 100644 > --- a/drivers/mmc/fsl_esdhc.c > +++ b/drivers/mmc/fsl_esdhc.c > @@ -1,7 +1,7 @@ > // SPDX-License-Identifier: GPL-2.0+ > /* > * Copyright 2007, 2010-2011 Freescale Semiconductor, Inc > - * Copyright 2019-2020 NXP > + * Copyright 2019-2021 NXP > * Andy Fleming > * > * Based vaguely on the pxa mmc code: > @@ -795,10 +795,21 @@ static void fsl_esdhc_get_cfg_common(struct > fsl_esdhc_priv *priv, > u32 caps; > > caps = esdhc_read32(®s->hostcapblt); > + > + /* > + * For eSDHC, power supply is through peripheral circuit. Some eSDHC > + * versions have value 0 of the bit but that does not reflect the > + * truth. 3.3V is common for SD/MMC, and is supported for all boards > + * with eSDHC in current u-boot. So, make 3.3V is supported in > + * default in code. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled > + * if future board does not support 3.3V. > + */ > + caps |= HOSTCAPBLT_VS33; > + if (IS_ENABLED(CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT)) > + caps &= ~HOSTCAPBLT_VS33; > + > if (IS_ENABLED(CONFIG_SYS_FSL_ERRATUM_ESDHC135)) > caps &= ~(HOSTCAPBLT_SRS | HOSTCAPBLT_VS18 | HOSTCAPBLT_VS30); > - if (IS_ENABLED(CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33)) > - caps |= HOSTCAPBLT_VS33; > if (caps & HOSTCAPBLT_VS18) > cfg->voltages |= MMC_VDD_165_195; > if (caps & HOSTCAPBLT_VS30) >