On 23/06/21 05:32PM, Jagan Teki wrote:
> On Wed, May 5, 2021 at 3:11 PM Pratyush Yadav <p.ya...@ti.com> wrote:
> >
> > Hi,
> >
> > This series adds support for octal DTR flashes in the SPI NOR framework,
> > and then adds hooks for the Cypress S28HS512T and Micron MT35XU512ABA
> > flashes.
> >
> > The Cadence QSPI controller driver is also updated to run in Octal DTR
> > mode.
> >
> > Tested on TI J721E for MT35XU512ABA and J7200 for S28HS512T. Also tested
> > on MT25QU512A for regressions.
> >
> > Changes in v9:
> > - Fix a typo in patch 26 commit message.
> >
> > - Add Sean's Reviewed-by in patch 3.
> >
> > - Drop the 2-byte check from spi_mem_dtr_supports_op(). Instead, perform
> > a even-byte length check on all 4 phases. Only do this when the
> > buswidth of the phase is 8.
> >
> > - Make template ops in spi_nor_check_readop() and spi_nor_check_pp()
> > have 2-byte data phase so they don't get rejected when 8D-8D-8D
> > protocol is being used.
> >
> > Changes in v8:
> > - Rebase on latest master, fixing merge conflicts.
> >
> > - Fix a regression related to address width that was discovered on
> > Linux.
> >
> > - Port spi_mem_dtr_supports_op() from Linux and use it in Cadence qspi
> > driver.
> >
> > - Do not set non-volatile Uniform Sector mode bit on S28HS512T. Instead
> > use Takahiro's non-uniform erase patch to enable non-uniform erases.
> >
> > - Make sure spi_nor_write_reg() does not set data direction to out when
> > there is no data to write, like in write enable.
> >
> > - Set buswidths to 0 before calling spi_nor_setup_op(), like how it is
> > done in Linux.
> >
> > Changes in v7:
> > - Port back changes requested on the Linux series.
> >
> > - Introduce the flag SPI_NOR_OCTAL_DTR_PP to indicate 8D page program
> > support since it can't be detected from SFDP.
> >
> > - Re-order Profile 1.0 related defines by DWORD order.
> >
> > - Drop local variables addr_width and dummy in spi_nor_read_sr()
> > spi_nor_read_fsr().
> >
> > - Do not make having command opcode extension as a reserved field fatal.
> >
> > - Update doc comment for spi_nor_parse_profile1() and
> > spi_nor_cypress_octal_dtr_enable() to add missing fields.
> >
> > - Move rdsr parameter parsing to where opcode is parsed because it is
> > from the same DWORD.
> >
> > - Convert a comment in Profile 1.0 parsing from multi-line to one line.
> >
> > - Rename 'table' to 'dwords' in xSPI Profile 1.0 parsing.
> >
> > - Update spi_nor_check_readop() and spi_nor_check_pp() to use
> > spi_nor_setup_op() so the buswidths are properly set up for DTR ops.
> >
> > - Do not set Uniform Sector bit on the Cypress S28HS512T flash if it is
> > already set. It will avoid wearing out the non-volatile bit.
> >
> > - Enable DQS for Micron MT35XU512ABA. No reason not to.
> >
> > - Avoid enabling 4-byte addressing mode for all DTR ops instead of just
> > Octal DTR ops. This is based on the assumption that DTR ops can only
> > use 4-byte addressing.
> >
> > - Make spi_nor_set_fixups() static.
> >
> > - Add flag SPI_NOR_OCTAL_DTR_PP to both Cypress S28HS512T and Micron
> > MT35XU512ABA.
> >
> > - Use values set up by spi-{rx,tx}-bus-width via device tree to
> > determine if the controller supports the op or not. Gives more
> > flexibility to choose protocol per-board.
> >
> > - Use tiny SPI NOR on x530 because of size constraints.
> >
> > Changes in v6:
> > - Use "# CONFIG_SPI_FLASH_SMART_HWCAPS is not set" instead of
> > "CONFIG_SPI_FLASH_SMART_HWCAPS=n" in x530_defconfig.
> >
> > Changes in v5:
> > - Fix build breaking when CONFIG_SPL_SPI_FLASH_TINY is enabled because
> > spi-nor-tiny did not have spi_nor_remove().
> >
> > - The build was breaking in x530 because of SPL size too big. Fix it by
> > the below changes.
> >
> > - Re-introduce old hwcaps selection logic and put the new one behind a
> > config. This lets boards with size restrictions use the old logic
> > which takes up less space. The code was getting hard to manage with
> > the old code behind ifdefs. So, re-structure the old hwcaps selection
> > logic and move it into one function: spi_nor_adjust_hwcaps(). This
> > way, the common code just calls spi_nor_adjust_hwcaps(), but the old
> > or new hwcaps selection is used based on the config option selected.
> >
> > - Put spi_nor_soft_reset() behind the config option SPI_NOR_SOFT_RESET.
> >
> > - Rename the config option used for soft resetting on boot to
> > SPI_NOR_SOFT_RESET_ON_BOOT to make its intention clearer.
> >
> > - Put the fixup hooks of MT35XU512ABA and S28HS512T flashes behind
> > config options to reduce code size on platforms that don't need them.
> >
> > - Introduce spi_nor_set_fixups(). Earlier, the fixup members of each
> > flash was specified in spi-nor-ids.c. This meant they had to be
> > declared as extern in sf_internal.h. But since spi-nor-tiny.c also
> > uses it, and it doesn't have those fixups, they had to be put behind
> > in an ifdef. The ".fixups = " assignment in spi-nor-ids.c also had to
> > be put in an ifdef to account for spi-nor-tiny.c not having the fixup
> > hooks. On top of this, the fixup of each flash is behind the flash's
> > config.
> >
> > All this lead to a soup of ifdefs that wasn't easy to digest. So don't
> > set the fixups in the common code. Instead, add a function in
> > spi-nor-core.c that sets the fixups of each flash. This isn't ideal,
> > but its the best compromise I could figure out.
> >
> > - Build were breaking with boards that use spi-mem-nodm.c because it
> > doesn't have spi_mem_supports_op() which is needed for smart hwcaps
> > selection. Add an equivalent to spi_mem_default_supports_op() there.
> >
> > - Replace uses of sizeof(op->cmd.opcode) with op->cmd.nbytes.
> >
> > - Do not set quad_enable to NULL if the value is set to reserved.
> > Instead just print a warning and go on. quad_enable should be set to
> > NULL in fixup hooks instead. Suggested on the Linux list.
> >
> > - Set dummy cycles for DTR mode in spi_nor_micron_octal_dtr_enable()
> > instead of in the post sfdp hook. This keeps the flash functional in
> > case Octal DTR mode is not selected.
> >
> > - Only use nor->rdsr_addr_nbytes and nor->rdsr_dummy when in Octal DTR
> > mode. This makes sure the flash is functional in case Octal DTR is not
> > selected.
> >
> > - Rebase on latest master and fix a small merge conflict.
> >
> > Changes in v4:
> > - Fix BFPT parsing stopping too early for JESD216 rev B flashes.
> >
> > - Instead of just checking for spi_nor_get_protocol_width() in
> > spi_nor_octal_dtr_enable(), make sure the protocol is
> > SNOR_PROTO_8_8_8_DTR since get_protocol_width() only cares about data
> > width.
> >
> > - Do not enable stateful X-X-X modes if the reset line is broken.
> >
> > - Instead of setting SNOR_READ_HWCAPS_8_8_8_DTR from Profile 1.0 table
> > parsing, do it in spi_nor_info_init_params() instead based on the
> > SPI_NOR_OCTAL_DTR_READ flag instead.
> >
> > - Set SNOR_HWCAPS_PP_8_8_8_DTR in s28hs post_sfdp hook since this
> > capability is no longer set in Profile 1.0 parsing.
> >
> > - Rename spi_nor_cypress_octal_enable() to
> > spi_nor_cypress_octal_dtr_enable().
> >
> > - Instead of hard-coding 8D-8D-8D Fast Read dummy cycles to 20, find
> > them out from the Profile 1.0 table.
> >
> > - Call post-bfpt fixup when exiting early because of JESD rev A.
> >
> > - Do not make an invalid Quad Enable BFPT field a fatal error. Silently
> > ignore it by assuming no quad enable bit is present.
> >
> > - Set cmd.nbytes to 1 when using SPI_MEM_OP_CMD().
> >
> > - Reject ops with more than 1 command byte in
> > spi_mem_default_supports_op().
> >
> > - Drop flag SPI_NOR_SOFT_RESET. Instead, discover soft reset capability
> > via BFPT.
> >
> > - Add missing headers that were removed from common header.
> >
> > Changes in v3:
> > - Read 2 bytes in Octal DTR mode when reading SR and FSR to avoid
> > tripping up controllers.
> >
> > - Use op->data.nbytes as a measure of whether the data phase exists or
> > not. This fixes data buswidth not being updadted for SR and FSR reads
> > because they keep data buffer as NULL when calling spi_nor_setup_op().
> >
> > - Add support for Micron mt35xu512aba to run in Octal DTR mode.
> >
> > Pratyush Yadav (27):
> > spi: spi-mem: allow specifying whether an op is DTR or not
> > spi: spi-mem: allow specifying a command's extension
> > spi: spi-mem: export spi_mem_default_supports_op()
> > spi: spi-mem: add spi_mem_dtr_supports_op()
> > spi: cadence-qspi: Do not calibrate when device tree sets read delay
> > spi: cadence-qspi: Add a small delay before indirect writes
> > spi: cadence-qspi: Add support for octal DTR flashes
> > arm: mvebu: x530: Use tiny SPI NOR
> > mtd: spi-nor-core: Fix address width on flash chips > 16MB
> > mtd: spi-nor-core: Add a ->setup() hook
> > mtd: spi-nor-core: Move SFDP related declarations to top
> > mtd: spi-nor-core: Introduce flash-specific fixup hooks
> > mtd: spi-nor-core: Rework hwcaps selection
> > mtd: spi-nor-core: Do not set data direction when there is no data
> > mtd: spi-nor-core: Add support for DTR protocol
> > mtd: spi-nor-core: prepare BFPT parsing for JESD216 rev D
> > mtd: spi-nor-core: Get command opcode extension type from BFPT
> > mtd: spi-nor-core: Parse xSPI Profile 1.0 table
> > mtd: spi-nor-core: Prepare Read SR and FSR for Octal DTR mode
> > mtd: spi-nor-core: Enable octal DTR mode when possible
> > mtd: spi-nor-core: Do not make invalid quad enable fatal
> > mtd: spi-nor-core: Detect Soft Reset sequence support from BFPT
> > mtd: spi-nor-core: Perform a Soft Reset on shutdown
> > mtd: spi-nor-core: Perform a Soft Reset on boot
> > mtd: spi-nor-core: allow truncated erases
> > mtd: spi-nor-core: Add support for Cypress Semper flash
> > mtd: spi-nor-core: Allow using Micron mt35xu512aba in Octal DTR mode
> >
> > Takahiro Kuwano (1):
> > mtd: spi-nor-core: Add non-uniform erase for Spansion/Cypress
>
> I found some merge conflicts, can you resend on top of u-boot-spi/master?
Ok. Will do.
>
> Jagan.
--
Regards,
Pratyush Yadav
Texas Instruments Inc.
