On 8/3/21 11:51 PM, Tom Rini wrote:
On Mon, Aug 02, 2021 at 05:27:59PM -0400, Tom Rini wrote:
On Thu, Jul 29, 2021 at 09:22:02AM +0200, Jan Kiszka wrote:
From: Jan Kiszka <jan.kis...@siemens.com>
This reverts commit 2359fa7a87848626bcbd3399e92c657595880cd7.
While the goal is valid and there is surely unused memory in that area,
we also have a lot of crucial things still located at the top-of-memory
while running lmb_alloc_base. Such things are the page table (tlb_addr),
relocated U-Boot and the active stack. Possibly more. So this patch was
premature, we will need relocations of those things first if we want to
use the range.
Fixes booting on the IOT2050, but likely also on other boards. It got
stuck on relocating the FDT - over the relocated U-Boot code.
Signed-off-by: Jan Kiszka <jan.kis...@siemens.com>
---
Practically,
void arch_lmb_reserve(struct lmb *lmb)
{
lmb_reserve(lmb, gd->relocaddr, gd->ram_top - gd->relocaddr);
}
worked as well for me - but it left the stack in danger.
I want to cycle back up to this practically part. Marek, would changing
the arch_lmb_reserve (or possibly even making this a more global thing /
option) still let the area you want exposed on rcar3 (I assume) be
exposed ? Or would it be covered again? Part of the problem,
practically speaking, is that we need to ensure that as part of
(attempting and likely succeeding in) booting the OS we don't overwrite
ourself and hang.
I think large part of the problem is the purpose of LMB is unclear at best.
The arch_lmb_reserve() says this:
54 void arch_lmb_reserve(struct lmb *lmb)
[...]
59 /*
60 * Booting a (Linux) kernel image
61 *
62 * Allocate space for command line and board info - the
63 * address should be as high as possible within the reach of
64 * the kernel (see CONFIG_SYS_BOOTMAPSZ settings), but in unused
65 * memory, which means far enough below the current stack
66 * pointer.
67 */
So basically reserve chunk of memory in the right place, which can be
safely passed to the kernel.
If that's not the case, and the LMB is used also to protect U-Boot from
overwriting itself, then the above comment is totally misleading and
wrong (and I have a feeling that is what you are trying to get on).
And if that's the case, then what we should reserve isn't
stack_bottom...ram_top, but really the work areas of U-Boot only (i.e. a
more fine grained reservation might be needed). For starters, replacing
ram_top with end of u-boot would do for my use case.
An alternative that I'm not 100% sure I like would be adjusting
env_get_bootm_size() so that the case of bootm_size and bootm_low are
unset, so we figure out a value based on gd->ram_top we also take in to
account where U-Boot itself is atm and exclude that.
I think we should really clarify the purpose of the LMB and make sure we
both understand it the same way.
It's possible that
if we had something like that at the start of the DT world, we wouldn't
have the code to disable fdt relocation, which really feels like it's
largely been "things crash when we relocate stuff, disable relocation"
and not so much "save a little boot time, we optimized things VERY
CAREFULLY".
Digging more. The comment about "Allocate space for command line and
board info" was introduced in 2d1916e48bd8 ("ARM: add flat device tree
support"). I happen to have the platform this was tested on, a
Beagleboard, around still and was able to boot that commit up and poke a
bit. It's effectively covering all of the running U-Boot with an LMB.
You can move on to commit b485556be51d ("ARM: enable device tree for
beagle"). That defines CONFIG_SYS_BOOTMAPSZ which is about start of
DRAM + a bit, to reserve space there that would be questionable on
ARM64. But all of that code area has been reworked since then.
So in sum, I think reverting 2359fa7a87848626bcbd3399e92c657595880cd7 is
right. U-Boot needs to be protected from being overwritten as it's
still alive at that point and relocating things around. This has always
been true. This has always been related to device tree booting.
What rcar is trying to do needs to be better explained first so that we
can figure out the right place to make some sort of update.
rcar might not relocate u-boot all the way to the end of DRAM, because
there might be some reserved memory at the end of DRAM used by one of
the other CPUs in the SoC, that's all.
