On 15/09/21 12:49PM, tkuw584...@gmail.com wrote: > From: Takahiro Kuwano <takahiro.kuw...@infineon.com> > > The current S25FS512S support has following issues that need to be fixed. > > - Non-uniform sectors by factory default. The setting needs to be > checked and assign erase hook as needed. > - Page size is wrongly advertised in SFDP. > - READ_1_1_2 (3Bh/3Ch), READ_1_1_4 (6Bh/6Ch), and PP_1_1_4 (32h/34h) > are not supported. > - Bank Address Register (BAR) is not supported. > > In addtion, volatile version of Quad Enable is used for safety. > > For future use, the fixups is assigned for S25FS-S family. > > The datasheet can be found in the following link. > https://www.cypress.com/file/216376/download > > Tested on Xilinx Zynq-7000 FPGA board. > > Signed-off-by: Takahiro Kuwano <takahiro.kuw...@infineon.com> > --- > drivers/mtd/spi/spi-nor-core.c | 101 +++++++++++++++++++++++++++++++++ > 1 file changed, 101 insertions(+) > > diff --git a/drivers/mtd/spi/spi-nor-core.c b/drivers/mtd/spi/spi-nor-core.c > index d5d905fa5a..5e847ebf6a 100644 > --- a/drivers/mtd/spi/spi-nor-core.c > +++ b/drivers/mtd/spi/spi-nor-core.c > @@ -3097,6 +3097,102 @@ static int spi_nor_setup(struct spi_nor *nor, const > struct flash_info *info, > } > > #ifdef CONFIG_SPI_FLASH_SPANSION > +static int s25fs_s_quad_enable(struct spi_nor *nor) > +{ > + return spansion_quad_enable_volatile(nor, 0, 8); > +} > + > +static int s25fs_s_erase_non_uniform(struct spi_nor *nor, loff_t addr) > +{ > + /* Support 8 x 4KB sectors at bottom */ > + return spansion_erase_non_uniform(nor, addr, SPINOR_OP_BE_4K_4B, 0, > + SZ_32K); > +} > + > +static int s25fs_s_setup(struct spi_nor *nor, const struct flash_info *info, > + const struct spi_nor_flash_parameter *params) > +{ > + int ret; > + u8 cfr3v; > + > +#ifdef CONFIG_SPI_FLASH_BAR
Avoid using #ifdef. Prefer if (CONFIG_IS_ENABLED(SPI_FLASH_BAR) instead. > + return -ENOTSUPP; /* Bank Address Register is not supported */ Same question as the other patch I just reviewed. What would happen if we don't do this? > +#endif > + /* > + * Read CR3V to check if uniform sector is selected. If not, assign an > + * erase hook that supports non-uniform erase. > + */ > + ret = spansion_read_any_reg(nor, SPINOR_REG_ADDR_CFR3V, 8, &cfr3v); Don't hard-code the 8. Use a #define instead. > + if (ret) > + return ret; > + if (!(cfr3v & CFR3V_UNHYSA)) > + nor->erase = s25fs_s_erase_non_uniform; Ok, but you still don't check for top/bottom configuration. This is the same as the S25Hx flashes, right? > + > + return spi_nor_default_setup(nor, info, params); > +} > + > +static void s25fs_s_default_init(struct spi_nor *nor) > +{ > + nor->setup = s25fs_s_setup; > +} > + > +static int s25fs_s_post_bfpt_fixup(struct spi_nor *nor, > + const struct sfdp_parameter_header *header, > + const struct sfdp_bfpt *bfpt, > + struct spi_nor_flash_parameter *params) > +{ > + int ret; > + u8 cfr3v; > + > + /* The erase size is set to 4K from BFPT, but it's wrong. Fix it. */ > + nor->erase_opcode = SPINOR_OP_SE; > + nor->mtd.erasesize = nor->info->sector_size; > + > + if (params->size > SZ_16M) { > + ret = nor->write_reg(nor, SPINOR_OP_EN4B, NULL, 0); set_4byte() should call this as well, right? Why call it here? > + if (ret) > + return ret; > + nor->addr_width = 4; > + } else { > + nor->addr_width = 3; > + } > + > + /* > + * The page_size is set to 512B from BFPT, but it actually depends on > + * the configuration register. Look up the CFR3V and determine the > + * page_size. > + */ > + ret = spansion_read_any_reg(nor, SPINOR_REG_ADDR_CFR3V, 8, &cfr3v); > + if (ret) > + return ret; > + > + if (cfr3v & CFR3V_PGMBUF) > + params->page_size = 512; > + else > + params->page_size = 256; > + > + return 0; > +} > + > +static void s25fs_s_post_sfdp_fixup(struct spi_nor *nor, > + struct spi_nor_flash_parameter *params) > +{ > + /* READ_1_1_2 is not supported */ > + params->hwcaps.mask &= ~SNOR_HWCAPS_READ_1_1_2; > + /* READ_1_1_4 is not supported */ > + params->hwcaps.mask &= ~SNOR_HWCAPS_READ_1_1_4; > + /* PP_1_1_4 is not supported */ > + params->hwcaps.mask &= ~SNOR_HWCAPS_PP_1_1_4; > + /* Use volatile register to enable quad */ > + params->quad_enable = s25fs_s_quad_enable; > +} > + > +static struct spi_nor_fixups s25fs_s_fixups = { > + .default_init = s25fs_s_default_init, > + .post_bfpt = s25fs_s_post_bfpt_fixup, > + .post_sfdp = s25fs_s_post_sfdp_fixup, > +}; > + > static int s25hx_t_mdp_ready(struct spi_nor *nor) > { > u32 addr; > @@ -3644,6 +3740,11 @@ void spi_nor_set_fixups(struct spi_nor *nor) > break; > } > } > + > + /* For FS-S (family ID = 0x81) */ > + if (JEDEC_MFR(nor->info) == SNOR_MFR_SPANSION && > + nor->info->id[5] == 0x81) > + nor->fixups = &s25fs_s_fixups; Ok. > #endif > > #ifdef CONFIG_SPI_FLASH_S28HS512T > -- > 2.25.1 > -- Regards, Pratyush Yadav Texas Instruments Inc.