From: Takahiro Kuwano <takahiro.kuw...@infineon.com>
The current S25FS512S support has following issues that need to be fixed.
- Non-uniform sectors by factory default. The setting needs to be
checked and assign erase hook as needed.
- Page size is wrongly advertised in SFDP.
- READ_1_1_2 (3Bh/3Ch), READ_1_1_4 (6Bh/6Ch), and PP_1_1_4 (32h/34h)
are not supported.
- Bank Address Register (BAR) is not supported.
In addtion, volatile version of Quad Enable is used for safety.
For future use, the fixups is assigned for S25FS-S family.
The datasheet can be found in the following link.
https://www.cypress.com/file/216376/download
Tested on Xilinx Zynq-7000 FPGA board.
Signed-off-by: Takahiro Kuwano <takahiro.kuw...@infineon.com>
---
Changes in v2:
- Add #define S25FS_S_RDAR_DUMMY and remove hard-coding
- Remove #ifdef CONFIG_SPI_FLASH_BAR
drivers/mtd/spi/spi-nor-core.c | 108 +++++++++++++++++++++++++++++++++
1 file changed, 108 insertions(+)
diff --git a/drivers/mtd/spi/spi-nor-core.c b/drivers/mtd/spi/spi-nor-core.c
index f1b4e5ea8e..349b2f3f23 100644
--- a/drivers/mtd/spi/spi-nor-core.c
+++ b/drivers/mtd/spi/spi-nor-core.c
@@ -3099,6 +3099,109 @@ static int spi_nor_setup(struct spi_nor *nor, const
struct flash_info *info,
}
#ifdef CONFIG_SPI_FLASH_SPANSION
+
+/* Number of dummy cycle for Read Any Register (RDAR) op. */
+#define S25FS_S_RDAR_DUMMY 8
+
+static int s25fs_s_quad_enable(struct spi_nor *nor)
+{
+ return spansion_quad_enable_volatile(nor, 0, S25FS_S_RDAR_DUMMY);
+}
+
+static int s25fs_s_erase_non_uniform(struct spi_nor *nor, loff_t addr)
+{
+ /* Support 8 x 4KB sectors at bottom */
+ return spansion_erase_non_uniform(nor, addr, SPINOR_OP_BE_4K_4B, 0,
+ SZ_32K);
+}
+
+static int s25fs_s_setup(struct spi_nor *nor, const struct flash_info *info,
+ const struct spi_nor_flash_parameter *params)
+{
+ int ret;
+ u8 cfr3v;
+
+ /* Bank Address Register is not supported */
+ if (CONFIG_IS_ENABLED(SPI_FLASH_BAR))
+ return -ENOTSUPP;
+
+ /*
+ * Read CR3V to check if uniform sector is selected. If not, assign an
+ * erase hook that supports non-uniform erase.
+ */
+ ret = spansion_read_any_reg(nor, SPINOR_REG_ADDR_CFR3V,
+ S25FS_S_RDAR_DUMMY, &cfr3v);
+ if (ret)
+ return ret;
+ if (!(cfr3v & CFR3V_UNHYSA))
+ nor->erase = s25fs_s_erase_non_uniform;
+
+ return spi_nor_default_setup(nor, info, params);
+}
+
+static void s25fs_s_default_init(struct spi_nor *nor)
+{
+ nor->setup = s25fs_s_setup;
+}
+
+static int s25fs_s_post_bfpt_fixup(struct spi_nor *nor,
+ const struct sfdp_parameter_header *header,
+ const struct sfdp_bfpt *bfpt,
+ struct spi_nor_flash_parameter *params)
+{
+ int ret;
+ u8 cfr3v;
+
+ /* The erase size is set to 4K from BFPT, but it's wrong. Fix it. */
+ nor->erase_opcode = SPINOR_OP_SE;
+ nor->mtd.erasesize = nor->info->sector_size;
+
+ if (params->size > SZ_16M) {
+ ret = nor->write_reg(nor, SPINOR_OP_EN4B, NULL, 0);
+ if (ret)
+ return ret;
+ nor->addr_width = 4;
+ } else {
+ nor->addr_width = 3;
+ }
+
+ /*
+ * The page_size is set to 512B from BFPT, but it actually depends on
+ * the configuration register. Look up the CFR3V and determine the
+ * page_size.
+ */
+ ret = spansion_read_any_reg(nor, SPINOR_REG_ADDR_CFR3V,
+ S25FS_S_RDAR_DUMMY, &cfr3v);
+ if (ret)
+ return ret;
+
+ if (cfr3v & CFR3V_PGMBUF)
+ params->page_size = 512;
+ else
+ params->page_size = 256;
+
+ return 0;
+}
+
+static void s25fs_s_post_sfdp_fixup(struct spi_nor *nor,
+ struct spi_nor_flash_parameter *params)
+{
+ /* READ_1_1_2 is not supported */
+ params->hwcaps.mask &= ~SNOR_HWCAPS_READ_1_1_2;
+ /* READ_1_1_4 is not supported */
+ params->hwcaps.mask &= ~SNOR_HWCAPS_READ_1_1_4;
+ /* PP_1_1_4 is not supported */
+ params->hwcaps.mask &= ~SNOR_HWCAPS_PP_1_1_4;
+ /* Use volatile register to enable quad */
+ params->quad_enable = s25fs_s_quad_enable;
+}
+
+static struct spi_nor_fixups s25fs_s_fixups = {
+ .default_init = s25fs_s_default_init,
+ .post_bfpt = s25fs_s_post_bfpt_fixup,
+ .post_sfdp = s25fs_s_post_sfdp_fixup,
+};
+
static int s25hx_t_mdp_ready(struct spi_nor *nor)
{
u32 addr;
@@ -3646,6 +3749,11 @@ void spi_nor_set_fixups(struct spi_nor *nor)
break;
}
}
+
+ /* For FS-S (family ID = 0x81) */
+ if (JEDEC_MFR(nor->info) == SNOR_MFR_SPANSION &&
+ nor->info->id[5] == 0x81)
+ nor->fixups = &s25fs_s_fixups;
#endif
#ifdef CONFIG_SPI_FLASH_S28HS512T
--
2.25.1
