The watchdog timer is part of the sl28cpld management controller. The
watchdog timer usually supervises the bootloader boot-up and if it bites
the failsafe bootloader will be activated. Apart from that it supports
the usual board level reset and one SMARC speciality: driving the
WDT_TIMEOUT# signal.
Signed-off-by: Michael Walle <mich...@walle.cc>
---
MAINTAINERS | 1 +
doc/board/kontron/sl28.rst | 53 +++++++++++-----
drivers/watchdog/Kconfig | 7 ++
drivers/watchdog/Makefile | 1 +
drivers/watchdog/sl28cpld-wdt.c | 109 ++++++++++++++++++++++++++++++++
5 files changed, 154 insertions(+), 17 deletions(-)
create mode 100644 drivers/watchdog/sl28cpld-wdt.c
diff --git a/MAINTAINERS b/MAINTAINERS
index e9d0bd0818..d7f09e1c81 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1104,6 +1104,7 @@ SL28CLPD
M: Michael Walle <mich...@walle.cc>
S: Maintained
F: drivers/misc/sl28cpld.c
+F: drivers/watchdog/sl28cpld-wdt.c
SPI
M: Jagan Teki <ja...@amarulasolutions.com>
diff --git a/doc/board/kontron/sl28.rst b/doc/board/kontron/sl28.rst
index c7b18bed10..c2cdc5e424 100644
--- a/doc/board/kontron/sl28.rst
+++ b/doc/board/kontron/sl28.rst
@@ -35,23 +35,6 @@ The board is fully failsafe, you can't break anything. But
because you've
disabled the builtin watchdog you might have to manually enter failsafe
mode by asserting the ``FORCE_RECOV#`` line during board reset.
-Disable the builtin watchdog
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-
-- boot into the failsafe bootloader, either by asserting the
- ``FORCE_RECOV#`` line or if you still have the original bootloader
- installed you can use the command::
-
- > wdt dev cpld_watchdog@4a; wdt expire 1
-
-- in the failsafe bootloader use the "sl28 nvm" command to disable
- the automatic start of the builtin watchdog::
-
- > sl28 nvm 0008
-
-- power-cycle the board
-
-
Update image
------------
@@ -82,6 +65,42 @@ u-boot (yet). But you can use the i2c command to access it.
> i2c md 4a 3.1 1
+Builtin watchdog
+----------------
+
+The builtin watchdog will supervise the bootloader startup. If anything
+goes wrong it will reset the board and boot into the failsafe bootloader.
+
+Once the bootloader is started successfully, it will disable the watchdog
+timer.
+
+wdt command flags
+^^^^^^^^^^^^^^^^^
+
+The `wdt start` as well as the `wdt expire` command take a flags argument.
+The supported bitmask is as follows.
+
+| Bit | Description |
+| --- | ----------------------------- |
+| 0 | Enable failsafe mode |
+| 1 | Lock the control register |
+| 2 | Disable board reset |
+| 3 | Enable WDT_TIME_OUT# line |
+
+For example, you can use `wdt expire 1` to issue a reset and boot into the
+failsafe bootloader.
+
+Disable the builtin watchdog
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+If for some reason, this isn't a desired behavior, the watchdog can also
+be configured to not be enabled on board reset. It's configuration is saved
+in the non-volatile board configuration bits. To change these you can use
+the `sl28 nvm` command.
+
+For more information on the non-volatile board configuration bits, see the
+following section.
+
Non-volatile Board Configuration Bits
-------------------------------------
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index 1177f17fd8..a232b595ba 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -257,6 +257,13 @@ config WDT_SBSA
In the single stage mode, when the timeout is reached, your system
will be reset by WS1. The first signal (WS0) is ignored.
+config WDT_SL28CPLD
+ bool "sl28cpld watchdog timer support"
+ depends on WDT && SL28CPLD
+ help
+ Enable support for the watchdog timer in the Kontron sl28cpld
+ management controller.
+
config WDT_SP805
bool "SP805 watchdog timer support"
depends on WDT
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index fa7ce583ce..8c6e5326c0 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -34,6 +34,7 @@ obj-$(CONFIG_WDT_OCTEONTX) += octeontx_wdt.o
obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o
obj-$(CONFIG_WDT_SBSA) += sbsa_gwdt.o
obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o
+obj-$(CONFIG_WDT_SL28CPLD) += sl28cpld-wdt.o
obj-$(CONFIG_WDT_SP805) += sp805_wdt.o
obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o
obj-$(CONFIG_WDT_SUNXI) += sunxi_wdt.o
diff --git a/drivers/watchdog/sl28cpld-wdt.c b/drivers/watchdog/sl28cpld-wdt.c
new file mode 100644
index 0000000000..af5a6b1a28
--- /dev/null
+++ b/drivers/watchdog/sl28cpld-wdt.c
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Watchdog driver for the sl28cpld
+ *
+ * Copyright (c) 2021 Michael Walle <mich...@walle.cc>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <wdt.h>
+#include <sl28cpld.h>
+#include <div64.h>
+
+#define SL28CPLD_WDT_CTRL 0x00
+#define WDT_CTRL_EN0 BIT(0)
+#define WDT_CTRL_EN1 BIT(1)
+#define WDT_CTRL_EN_MASK GENMASK(1, 0)
+#define WDT_CTRL_LOCK BIT(2)
+#define WDT_CTRL_ASSERT_SYS_RESET BIT(6)
+#define WDT_CTRL_ASSERT_WDT_TIMEOUT BIT(7)
+#define SL28CPLD_WDT_TIMEOUT 0x01
+#define SL28CPLD_WDT_KICK 0x02
+#define WDT_KICK_VALUE 0x6b
+
+static int sl28cpld_wdt_reset(struct udevice *dev)
+{
+ return sl28cpld_write(dev, SL28CPLD_WDT_KICK, WDT_KICK_VALUE);
+}
+
+static int sl28cpld_wdt_start(struct udevice *dev, u64 timeout, ulong flags)
+{
+ int ret, val;
+
+ val = sl28cpld_read(dev, SL28CPLD_WDT_CTRL);
+ if (val < 0)
+ return val;
+
+ /* (1) disable watchdog */
+ val &= ~WDT_CTRL_EN_MASK;
+ ret = sl28cpld_write(dev, SL28CPLD_WDT_CTRL, val);
+ if (ret)
+ return ret;
+
+ /* (2) set timeout */
+ ret = sl28cpld_write(dev, SL28CPLD_WDT_TIMEOUT, lldiv(timeout, 1000));
+ if (ret)
+ return ret;
+
+ /* (3) kick it, will reset timer to the timeout value */
+ ret = sl28cpld_wdt_reset(dev);
+ if (ret)
+ return ret;
+
+ /* (4) enable either recovery or normal one */
+ if (flags & BIT(0))
+ val |= WDT_CTRL_EN1;
+ else
+ val |= WDT_CTRL_EN0;
+
+ if (flags & BIT(1))
+ val |= WDT_CTRL_LOCK;
+
+ if (flags & BIT(2))
+ val &= ~WDT_CTRL_ASSERT_SYS_RESET;
+ else
+ val |= WDT_CTRL_ASSERT_SYS_RESET;
+
+ if (flags & BIT(3))
+ val |= WDT_CTRL_ASSERT_WDT_TIMEOUT;
+ else
+ val &= ~WDT_CTRL_ASSERT_WDT_TIMEOUT;
+
+ return sl28cpld_write(dev, SL28CPLD_WDT_CTRL, val);
+}
+
+static int sl28cpld_wdt_stop(struct udevice *dev)
+{
+ int val;
+
+ val = sl28cpld_read(dev, SL28CPLD_WDT_CTRL);
+ if (val < 0)
+ return val;
+
+ return sl28cpld_write(dev, SL28CPLD_WDT_CTRL, val & ~WDT_CTRL_EN_MASK);
+}
+
+static int sl28cpld_wdt_expire_now(struct udevice *dev, ulong flags)
+{
+ return sl28cpld_wdt_start(dev, 0, flags);
+}
+
+static const struct wdt_ops sl28cpld_wdt_ops = {
+ .start = sl28cpld_wdt_start,
+ .reset = sl28cpld_wdt_reset,
+ .stop = sl28cpld_wdt_stop,
+ .expire_now = sl28cpld_wdt_expire_now,
+};
+
+static const struct udevice_id sl28cpld_wdt_ids[] = {
+ { .compatible = "kontron,sl28cpld-wdt", },
+ {}
+};
+
+U_BOOT_DRIVER(sl28cpld_wdt) = {
+ .name = "sl28cpld-wdt",
+ .id = UCLASS_WDT,
+ .of_match = sl28cpld_wdt_ids,
+ .ops = &sl28cpld_wdt_ops,
+};
--
2.30.2
