>
>
> Hi,
>
> On Tue, 30 Nov 2021 at 00:26, Josef Luštický <jo...@lusticky.cz> wrote:
> >>
> >>
> >> Hi Josef
> >>
> >> On Fri, Nov 26, 2021 at 10:56 AM Josef Lusticky <jo...@lusticky.cz>
> wrote:
> >> >
> >> > TI AM43xx SoC supports various boot devices (peripherals).
> >> > There is already handoff mechanism prepared to allow passing
> >> > the information which boot device was used to load the SPL.
> >> >
> >> > Use the handoff mechanism to pass this information to U-Boot proper
> >> > and set the "boot_device" environment variable in board_late_init.
> >> >
> >> > Signed-off-by: Josef Lusticky <jo...@lusticky.cz>
> >> > Cc: Tom Rini <tr...@konsulko.com>
> >> > Cc: Lokesh Vutla <lokeshvu...@ti.com>
> >> > Cc: Michael Trimarchi <mich...@amarulasolutions.com>
> >> > ---
> >> >
> >> > I use the boot_device variable later in U-Boot scripting - e.g. to
> avoid running
> >> > bootcmd when the SPL was loaded from UART but run it when loaded from
> MMC.
> >> > Only AM43xx is supported by this patch, but for other TI SoCs
> >> > the procedure should be the same:
> >> > - figure out supported boot devices from
> arch/arm/include/asm/arch-am33xx/spl.h
> >> > or arch/arm/include/asm/arch-omapX/spl.h
> >> > - implement setting the boot_device env variable in board_late_init()
> >> >
> >> > You'll need to enable the following in the config:
> >> > CONFIG_BLOBLIST=y (required by CONFIG_HANDOFF)
> >> > CONFIG_HANDOFF=y
> >> > CONFIG_BLOBLIST_ADDR=0x87000000 (i set this based on other values
> defined by
> >> > the DEFAULT_LINUX_BOOT_ENV macro in
> include/configs/ti_armv7_common.h, you
> >> > may want to use a different address)
> >> >
> >> > arch/arm/include/asm/handoff.h | 3 +++
> >> > arch/arm/mach-omap2/boot-common.c | 9 ++++++++
> >> > board/ti/am43xx/board.c | 38
> +++++++++++++++++++++++++++++++
> >> > 3 files changed, 50 insertions(+)
> >> >
> >> > diff --git a/arch/arm/include/asm/handoff.h
> b/arch/arm/include/asm/handoff.h
> >> > index 0790d2ab1e..1b7aa432a2 100644
> >> > --- a/arch/arm/include/asm/handoff.h
> >> > +++ b/arch/arm/include/asm/handoff.h
> >> > @@ -16,6 +16,9 @@
> >> > */
> >> > struct arch_spl_handoff {
> >> > ulong usable_ram_top;
> >> > +#ifdef CONFIG_ARCH_OMAP2PLUS
> >> > + u32 omap_boot_device;
> >> > +#endif
> >> > };
> >>
> >> Simon is working on a more structured way to pass arguments in
> >> multi-stage boot. I forget to read all the patches.
> >> Anyway adding a specific handoff parameter for one architecture makes
> >> no such sense. I will remind you that this
> >> was already implemented in the past using dts injection (something
> >> that I don't like)
> >>
> > Hi Michael,
> > thank you for your response.
> >
> > I agree that such support for a single architecture makes no such sense.
>
> Note that the more structured approach is in fact using a bloblist,
> and SPL handoff can just be one of the blobs. So this patch is not
> actually in conflict with that, and will 'just work' when standard
> flow is in there.
>
> As to the arch-specific nature of this, I would rather handle it by
> either avoiding the #ifdef (so the field is unused on other baords) or
> adding a new level of include for arch-specific handoff info, so that
> arch_spl_handoff includes mach_spl_handoff, for example.
>
> But other than that, and the comments below, it seems OK to me.
>
Thank you for your comments, Simon.
I find the split of arch_spl_handoff as a good idea.
I am also curious about how other platforms would
work with such a way of passing boot_device information
and other data.
There are some more boards on my table,
so I'll try to make a similar feature work on those boards to see if
the approach can be used in general.
But this will take some time...
> [..]
>
> Regards,
> Simon
>
