Add the device-tree for pine H64 model B from 5.15 mainline linux.

The differences between the pine H64 boards model A and model B are
irrelevant inside u-boot, but the device-tree name is relevant as
default for selecting the correct device-tree when booting linux.

Signed-off-by: Daniel Wagenknecht <dwag...@mailbox.org>
---
 arch/arm/dts/Makefile                       |  1 +
 arch/arm/dts/sun50i-h6-pine-h64-model-b.dts | 51 +++++++++++++++++++++
 2 files changed, 52 insertions(+)
 create mode 100644 arch/arm/dts/sun50i-h6-pine-h64-model-b.dts

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 7f622fedbd..a9618d80ca 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -658,6 +658,7 @@ dtb-$(CONFIG_MACH_SUN50I_H6) += \
        sun50i-h6-orangepi-lite2.dtb \
        sun50i-h6-orangepi-one-plus.dtb \
        sun50i-h6-pine-h64.dtb \
+       sun50i-h6-pine-h64-model-b.dtb \
        sun50i-h6-tanix-tx6.dtb
 dtb-$(CONFIG_MACH_SUN50I_H616) += \
        sun50i-h616-orangepi-zero2.dtb
diff --git a/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts 
b/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts
new file mode 100644
index 0000000000..686f58e770
--- /dev/null
+++ b/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2019 Corentin LABBE <cla...@baylibre.com>
+ */
+
+#include "sun50i-h6-pine-h64.dts"
+
+/ {
+       model = "Pine H64 model B";
+       compatible = "pine64,pine-h64-model-b", "allwinner,sun50i-h6";
+
+       /delete-node/ reg_gmac_3v3;
+
+       wifi_pwrseq: wifi_pwrseq {
+               compatible = "mmc-pwrseq-simple";
+               reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
+               post-power-on-delay-ms = <200>;
+       };
+};
+
+&hdmi_connector {
+       /delete-property/ ddc-en-gpios;
+};
+
+&emac {
+       phy-supply = <&reg_aldo2>;
+};
+
+&mmc1 {
+       vmmc-supply = <&reg_cldo3>;
+       vqmmc-supply = <&reg_aldo1>;
+       mmc-pwrseq = <&wifi_pwrseq>;
+       bus-width = <4>;
+       non-removable;
+       status = "okay";
+};
+
+&uart1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+       uart-has-rtscts;
+       status = "okay";
+
+       bluetooth {
+               compatible = "realtek,rtl8723bs-bt";
+               device-wake-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
+               host-wake-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */
+               enable-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */
+               max-speed = <1500000>;
+       };
+};
-- 
2.31.1

Reply via email to