Hi Adam On Sun, Feb 13, 2022 at 5:03 PM Adam Ford <aford...@gmail.com> wrote: > > On Sat, Feb 12, 2022 at 1:27 PM Michael Nazzareno Trimarchi > <mich...@amarulasolutions.com> wrote: > > > > Hi Tim > > > > You are using the imx8mm. I have problems on imx8mn. It's like some > > part is not implemented. Time to time power domain timeout if I > > enabled > > mipi pipeline > > If you're using ATF from its mainline branch, it likely does not have > the power domain code enabled, so many peripherals (including DSI and > CSI) likely won't work. > > The power-domain code would be located in gpc.v [1], but as far as I > know, attempts to push that upstream were abandoned in favor of having > Linux do the power domain stuff, so to use NXP's kernel, you'll need > NXP's ATF. > > [1] - > https://source.codeaurora.org/external/imx/imx-atf/tree/plat/imx/imx8m/imx8mn/gpc.c?h=lf_v2.4 >
I;m working on mainline on each component. I was thinking that blk-ctrl do the stuff there Michael > adam > > > > Michael > > > > On Wed, Feb 2, 2022 at 4:54 PM Tim Harvey <thar...@gateworks.com> wrote: > > > > > > On Wed, Feb 2, 2022 at 5:04 AM Michael Nazzareno Trimarchi > > > <mich...@amarulasolutions.com> wrote: > > > > > > > > Hi Adam > > > > > > > > On Wed, Feb 2, 2022 at 2:02 PM Adam Ford <aford...@gmail.com> wrote: > > > > > > > > > > On Wed, Feb 2, 2022 at 6:24 AM Michael Nazzareno Trimarchi > > > > > <mich...@amarulasolutions.com> wrote: > > > > > > > > > > > > Hi all > > > > > > > > > > > > I have now able to pack those combination and all of them look ok > > > > > > > > > > > > - mainline uboot > > > > > > - optee 3.15.0 > > > > > > - atf 2.5 > > > > > > - mainline kernel > > > > > > > > > > > > - mainline uboot > > > > > > - optee 3.15.0 > > > > > > - imx-atf rel_imx_5.4.70_2.3.2 > > > > > > - Linux rel_imx_5.4.70_2.3.2 > > > > > > > > > > > > I have a setup where I can test some peripherals. I can run an optee > > > > > > test on both combinations > > > > > > The big issue I have it's the DSIM display it's not working and > > > > > > crashes the kernel using the rel_imx_5.4.70_2.3.2 nxp version. The > > > > > > mipi > > > > > > randomly deadlock the booting. If I don't register the mipi part > > > > > > it's > > > > > > ok. Can someone have an idea? > > > > > > > > > > Are you using the Linux rel_imx_5.4.70_2.3.2 with imx-atf > > > > > rel_imx_5.4.70_2.3.2? > > > > > > > > > > The NXP kernel expects the NXP ATF code. The power-domain drivers in > > > > > the NXP branch make secure calls to ATF which enable/disable the > > > > > power-domains which control a bunch of peripherals like DSI, CSI, USB > > > > > and GPU. If you're using the mainline ATF, I don't believe it > > > > > contains the power-domain controllers, so when the Linux power-domain > > > > > drivers make the secure calls, it's likely the power-domains won't > > > > > change. > > > > > > > > - mainline uboot > > > > - optee 3.15.0 > > > > - imx-atf rel_imx_5.4.70_2.3.2 > > > > - Linux rel_imx_5.4.70_2.3.2 > > > > > > > > I have tried even to not load optee in the image but still the same > > > > > > > > Michael > > > > > > > > > > adam > > > > > > > > > > > > All of them can be test using a buildroot setup > > > > > > > > > > > > Michael > > > > > > > > > > Michael, > > > > > > I have not bothered with NXP's kernel, but I do have DSIM working on > > > 5.15 with a set of patches here > > > https://github.com/Gateworks/linux-venice if it is helpful. I've been > > > using this with a mainline U-Boot, imx-atf lf_v2.4. > > > > > > Tim > > > > > > > > -- > > Michael Nazzareno Trimarchi > > Co-Founder & Chief Executive Officer > > M. +39 347 913 2170 > > mich...@amarulasolutions.com > > __________________________________ > > > > Amarula Solutions BV > > Joop Geesinkweg 125, 1114 AB, Amsterdam, NL > > T. +31 (0)85 111 9172 > > i...@amarulasolutions.com > > www.amarulasolutions.com -- Michael Nazzareno Trimarchi Co-Founder & Chief Executive Officer M. +39 347 913 2170 mich...@amarulasolutions.com __________________________________ Amarula Solutions BV Joop Geesinkweg 125, 1114 AB, Amsterdam, NL T. +31 (0)85 111 9172 i...@amarulasolutions.com www.amarulasolutions.com
