Follow patch <f6adec1af4b2f5d3012480c6cdce7743b74a6156> (Allow using Micron
mt35xu512aba
in Octal DTR mode).
Enable Octal DTR mode with 20 dummy cycles to allow running at the
maximum supported frequency for adding Macronix flash in Octal DTR mode.
-https://www.mxic.com.tw/Lists/Datasheet/Attachments/7841/MX25LM51245G,%203V,%20512Mb,%20v1.1.pdf
Signed-off-by: JaimeLiao <jaimeliao...@gmail.com>
---
drivers/mtd/spi/spi-nor-core.c | 82 ++++++++++++++++++++++++++++++++++
include/linux/mtd/spi-nor.h | 12 ++++-
2 files changed, 92 insertions(+), 2 deletions(-)
diff --git a/drivers/mtd/spi/spi-nor-core.c b/drivers/mtd/spi/spi-nor-core.c
index d5d905fa5a..72250a83d1 100644
--- a/drivers/mtd/spi/spi-nor-core.c
+++ b/drivers/mtd/spi/spi-nor-core.c
@@ -3489,6 +3489,84 @@ static struct spi_nor_fixups mt35xu512aba_fixups = {
};
#endif /* CONFIG_SPI_FLASH_MT35XU */
+#if CONFIG_IS_ENABLED(SPI_FLASH_MACRONIX)
+/**
+ * spi_nor_macronix_octal_dtr_enable() - Enable octal DTR on Macronix flashes.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set Macronix max dummy cycles 20 to allow the flash to run at fastest
frequency.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_macronix_octal_dtr_enable(struct spi_nor *nor)
+{
+ struct spi_mem_op op;
+ int ret;
+ u8 buf;
+
+ ret = write_enable(nor);
+ if (ret)
+ return ret;
+
+ buf = SPINOR_REG_MXIC_DC_20;
+ op = (struct spi_mem_op)
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_CR2, 1),
+ SPI_MEM_OP_ADDR(4, SPINOR_REG_MXIC_CR2_DC, 1),
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_OUT(1, &buf, 1));
+
+ ret = spi_mem_exec_op(nor->spi, &op);
+ if (ret)
+ return ret;
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ return ret;
+
+ nor->read_dummy = MXIC_MAX_DC;
+ ret = write_enable(nor);
+ if (ret)
+ return ret;
+
+ buf = SPINOR_REG_MXIC_OPI_DTR_EN;
+ op = (struct spi_mem_op)
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_CR2, 1),
+ SPI_MEM_OP_ADDR(4, SPINOR_REG_MXIC_CR2_MODE, 1),
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_OUT(1, &buf, 1));
+
+ ret = spi_mem_exec_op(nor->spi, &op);
+ if (ret) {
+ dev_err(nor->dev, "Failed to enable octal DTR mode\n");
+ return ret;
+ }
+ nor->reg_proto = SNOR_PROTO_8_8_8_DTR;
+
+ return 0;
+}
+
+static void macronix_octal_default_init(struct spi_nor *nor)
+{
+ nor->octal_dtr_enable = spi_nor_macronix_octal_dtr_enable;
+}
+
+static void macronix_octal_post_sfdp_fixup(struct spi_nor *nor,
+ struct spi_nor_flash_parameter *params)
+{
+ /*
+ * Adding SNOR_HWCAPS_PP_8_8_8_DTR in hwcaps.mask when
+ * SPI_NOR_OCTAL_DTR_READ flag exists.
+ */
+ if (params->hwcaps.mask & SNOR_HWCAPS_READ_8_8_8_DTR)
+ params->hwcaps.mask |= SNOR_HWCAPS_PP_8_8_8_DTR;
+}
+
+static struct spi_nor_fixups macronix_octal_fixups = {
+ .default_init = macronix_octal_default_init,
+ .post_sfdp = macronix_octal_post_sfdp_fixup,
+};
+#endif /* CONFIG_SPI_FLASH_MACRONIX */
+
/** spi_nor_octal_dtr_enable() - enable Octal DTR I/O if needed
* @nor: pointer to a 'struct spi_nor'
*
@@ -3655,6 +3733,10 @@ void spi_nor_set_fixups(struct spi_nor *nor)
if (!strcmp(nor->info->name, "mt35xu512aba"))
nor->fixups = &mt35xu512aba_fixups;
#endif
+
+#if CONFIG_IS_ENABLED(SPI_FLASH_MACRONIX)
+ nor->fixups = ¯onix_octal_fixups;
+#endif /* SPI_FLASH_MACRONIX */
}
int spi_nor_scan(struct spi_nor *nor)
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index 7ddc4ba2bf..8682368f2f 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -116,8 +116,16 @@
#define XSR_RDY BIT(7) /* Ready */
/* Used for Macronix and Winbond flashes. */
-#define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */
-#define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */
+#define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */
+#define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */
+#define SPINOR_OP_RD_CR2 0x71 /* Read configuration
register 2 */
+#define SPINOR_OP_WR_CR2 0x72 /* Write configuration
register 2 */
+#define SPINOR_OP_MXIC_DTR_RD 0xee /* Fast Read opcode in
DTR mode */
+#define SPINOR_REG_MXIC_CR2_MODE 0x00000000 /* For setting octal
DTR mode */
+#define SPINOR_REG_MXIC_OPI_DTR_EN 0x2 /* Enable Octal DTR */
+#define SPINOR_REG_MXIC_CR2_DC 0x00000300 /* For setting dummy
cycles */
+#define SPINOR_REG_MXIC_DC_20 0x0 /* Setting dummy cycles
to 20 */
+#define MXIC_MAX_DC 20 /* Maximum value of
dummy cycles */
/* Used for Spansion flashes only. */
#define SPINOR_OP_BRWR 0x17 /* Bank register write */
--
2.17.1
