On 15.03.22 21:47, Fabio Estevam wrote:
From: Fabio Estevam <feste...@denx.de>
Conversion to DM_SERIAL is mandatory.
Select DM_SERIAL and add a imx6q-tbs2910-u-boot.dtsi file
that describes the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.
Remove the now unneeded board UART initialization.
Signed-off-by: Fabio Estevam <feste...@denx.de>
I will test this within the next few days, please give me a little more
time.
Thanks,
Soeren
---
arch/arm/dts/imx6q-tbs2910-u-boot.dtsi | 17 +++++++++++++++++
arch/arm/dts/imx6qdl.dtsi | 4 ++--
board/tbs/tbs2910/tbs2910.c | 26 --------------------------
configs/tbs2910_defconfig | 2 +-
4 files changed, 20 insertions(+), 29 deletions(-)
create mode 100644 arch/arm/dts/imx6q-tbs2910-u-boot.dtsi
diff --git a/arch/arm/dts/imx6q-tbs2910-u-boot.dtsi
b/arch/arm/dts/imx6q-tbs2910-u-boot.dtsi
new file mode 100644
index 000000000000..65ab052ac2c0
--- /dev/null
+++ b/arch/arm/dts/imx6q-tbs2910-u-boot.dtsi
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+&aips1 {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_uart1 {
+ u-boot,dm-pre-reloc;
+};
+
+&soc {
+ u-boot,dm-pre-reloc;
+};
+
+&uart1 {
+ u-boot,dm-pre-reloc;
+};
diff --git a/arch/arm/dts/imx6qdl.dtsi b/arch/arm/dts/imx6qdl.dtsi
index efd89510d512..d89272039b28 100644
--- a/arch/arm/dts/imx6qdl.dtsi
+++ b/arch/arm/dts/imx6qdl.dtsi
@@ -139,7 +139,7 @@
interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>;
};
- soc {
+ soc: soc {
#address-cells = <1>;
#size-cells = <1>;
compatible = "simple-bus";
@@ -283,7 +283,7 @@
status = "disabled";
};
- bus@2000000 { /* AIPS1 */
+ aips1: bus@2000000 { /* AIPS1 */
compatible = "fsl,aips-bus", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
diff --git a/board/tbs/tbs2910/tbs2910.c b/board/tbs/tbs2910/tbs2910.c
index faf73cc218c9..3a447ca8a93c 100644
--- a/board/tbs/tbs2910/tbs2910.c
+++ b/board/tbs/tbs2910/tbs2910.c
@@ -22,32 +22,12 @@
#include <asm/arch/sys_proto.h>
DECLARE_GLOBAL_DATA_PTR;
-#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-static iomux_v3_cfg_t const uart1_pads[] = {
- MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const uart2_pads[] = {
- MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
int dram_init(void)
{
gd->ram_size = 2048ul * 1024 * 1024;
return 0;
}
-static void setup_iomux_uart(void)
-{
- imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
- imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
-}
-
#ifdef CONFIG_FSL_ESDHC_IMX
/* set environment device to boot device when booting from SD */
int board_mmc_get_env_dev(int devno)
@@ -150,12 +130,6 @@ static void setup_display(void)
}
#endif /* CONFIG_VIDEO_IPUV3 */
-int board_early_init_f(void)
-{
- setup_iomux_uart();
- return 0;
-}
-
#ifdef CONFIG_CMD_BMODE
static const struct boot_mode board_boot_modes[] = {
/* 4 bit bus width */
diff --git a/configs/tbs2910_defconfig b/configs/tbs2910_defconfig
index 8a3316056408..63a778a45f0b 100644
--- a/configs/tbs2910_defconfig
+++ b/configs/tbs2910_defconfig
@@ -23,7 +23,6 @@ CONFIG_USE_PREBOOT=y
CONFIG_PREBOOT="echo PCI:; pci enum; pci 1; usb start; if hdmidet; then run
set_con_hdmi; else run set_con_serial; fi"
CONFIG_DEFAULT_FDT_FILE="imx6q-tbs2910.dtb"
CONFIG_PRE_CONSOLE_BUFFER=y
-CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="Matrix U-Boot> "
# CONFIG_CMD_BDI is not set
@@ -81,6 +80,7 @@ CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_DM_RTC=y
CONFIG_RTC_DS1307=y
+CONFIG_DM_SERIAL=y
CONFIG_MXC_UART=y
CONFIG_DM_THERMAL=y
CONFIG_IMX_THERMAL=y
