On 3/24/22 10:57, Robert Marko wrote:
Update the current uDPU defconfig with following changes:
* Disable CONFIG_SPI_BOOT, its not needed for booting and the device boots
from eMMC anyway.
* Disable CONFIG_SYS_CONSOLE_INFO_QUIET, there is no need to diverge from
other boards by not priting the console device
* Enable CONFIG_CMD_MTD in order to allow use of the MTD tool
* Disable CONFIG_CMD_MTDPARTS, with MTD now being able to parse partitions
from DTS there is no need for it, the default MTDPARTS were incorrect
anyway
* Enable CONFIG_MMC_HS200_SUPPORT, the eMMC used support both HS200 and
HS400 modes, so enable at least HS200 because Xenon driver does not
support HS400 currently
* Replace CONFIG_SPI_FLASH_BAR with CONFIG_SPI_FLASH_SFDP_SUPPORT
Utilize SFDP parsing instead of relying on the extended address registers
Signed-off-by: Robert Marko <robert.ma...@sartura.hr>
Applied to u-boot-marvell/master
Thanks,
Stefan
---
configs/uDPU_defconfig | 10 ++++------
1 file changed, 4 insertions(+), 6 deletions(-)
diff --git a/configs/uDPU_defconfig b/configs/uDPU_defconfig
index b5f2115e63..1a2182b823 100644
--- a/configs/uDPU_defconfig
+++ b/configs/uDPU_defconfig
@@ -16,9 +16,8 @@ CONFIG_DISTRO_DEFAULTS=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SYS_LOAD_ADDR=0x6000000
CONFIG_FIT=y
-CONFIG_SPI_BOOT=y
+CONFIG_FIT_VERBOSE=y
CONFIG_USE_PREBOOT=y
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
# CONFIG_DISPLAY_CPUINFO is not set
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_DISPLAY_BOARDINFO_LATE=y
@@ -32,6 +31,7 @@ CONFIG_SYS_PROMPT="uDPU>> "
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
CONFIG_CMD_PCI=y
CONFIG_CMD_SPI=y
CONFIG_CMD_USB=y
@@ -41,9 +41,6 @@ CONFIG_CMD_CACHE=y
CONFIG_CMD_TIME=y
CONFIG_CMD_MVEBU_BUBT=y
CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nor0=spi0"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=spi0:4m(uboot),-(rootfs)"
CONFIG_MAC_PARTITION=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
@@ -56,12 +53,13 @@ CONFIG_DM_I2C=y
CONFIG_DM_I2C_GPIO=y
CONFIG_SYS_I2C_MV=y
CONFIG_MISC=y
+CONFIG_MMC_HS200_SUPPORT=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_SDMA=y
CONFIG_MMC_SDHCI_XENON=y
CONFIG_MTD=y
CONFIG_DM_MTD=y
-CONFIG_SPI_FLASH_BAR=y
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
Viele Grüße,
Stefan Roese
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: s...@denx.de
