On 4/28/22 06:52, AKASHI Takahiro wrote:
On Wed, Apr 27, 2022 at 12:26:09PM +0900, AKASHI Takahiro wrote:
Heinrich,
On Tue, Apr 26, 2022 at 07:02:46PM +0200, Heinrich Schuchardt wrote:
On 4/26/22 16:44, AKASHI Takahiro wrote:
On Tue, Apr 26, 2022 at 03:57:26PM +0200, Heinrich Schuchardt wrote:
On 4/26/22 01:44, AKASHI Takahiro wrote:
I expect that boards that booted with previous versions of U-Boot using
the respective defconfig still boot. But they don't. Here is one example
(orangepi_pc_defconfig):
Found U-Boot script /boot.scr.uimg
189 bytes read in 2 ms (91.8 KiB/s)
## Executing script at 43100000
22979 bytes read in 8 ms (2.7 MiB/s)
98304 bytes read in 8 ms (11.7 MiB/s)
Booting /EFI\debian\grubarm.efi
Welcome to GRUB!
error: disk `,msdos2' not found.
grub rescue>
In U-Boot v2022.04 function efi_disk_register() ensured that all block
devices and their partitions were added as EFI handles.
Not the all block devices, but the block devices which have already
enumerated when efi_init_obj_list() is called.
But that
function is missing now.
What (boot) device are you using here?
Please show me the values of env variables, particularly, "boot_targets".
Please show me the content of boot.scr.uimg, too.
Please show me the output from
=> dm tree
=> efidebug devices
for 2022.04 and 2022.07-rc1.
-Takahiro Akashi
I am booting from mmc. Boot.scr just loads the device-tree from mmc-
mmcblk0 179:0 0 29.8G 0 disk
├─mmcblk0p1 179:1 0 1G 0 part /boot/efi
├─mmcblk0p2 179:2 0 1G 0 part /boot
└─mmcblk0p3 179:3 0 27.8G 0 part /
Okay.
U-Boot 2022.04 (Apr 26 2022 - 16:02:27 +0000) Allwinner Technology
------------------------------------------------------------------
grub> ls
(hd0) (hd0,msdos1) (hd1) (hd1,msdos3) (hd1,msdos2) (hd1,msdos1)
hd0 is a USB stick
hd1 is the SD card
boot.scr
--------
#
# flash-kernel: bootscr.sunxi
#
# boot script for Allwinner SunXi-based devices
# Mainline u-boot v2014.10 introduces a new default environment and
# a new common bootcmd handling for all platforms, which is not fully
# compatible with the old-style environment used by u-boot-sunxi.
# This script therefore needs to check in which environment it
# is running and set some variables accordingly.
# On u-boot-sunxi, this script assumes that ${device} and ${partition}
# are set.
# The new-style environment predefines ${boot_targets}, the old-style
# environment does not.
if test -n "${boot_targets}"
then
echo "Mainline u-boot / new-style environment detected."
# Mainline u-boot v2014.10 uses ${devtype}, ${devnum} and
# ${bootpart} where u-boot-sunxi uses ${device} and ${partition}.
# ${distro_bootpart} replaced ${bootpart} in u-boot v2016.01.
if test -z "${device}"; then setenv device "${devtype}"; fi
if test -z "${partition}${distro_bootpart}"; then setenv partition
"${devnum}:${bootpart}"; fi
if test -z "${partition}"; then setenv partition
"${devnum}:${distro_bootpart}"; fi
else
echo "U-boot-sunxi / old-style environment detected."
# U-boot-sunxi does not predefine kernel_addr_r, fdt_addr_r and
# ramdisk_addr_r, so they have to be manually set. Use the values
# from mainline u-boot v2014.10, except for ramdisk_addr_r,
# which is set to 0x44300000 to allow for initrds larger than
# 13MB on u-boot-sunxi.
setenv kernel_addr_r 0x42000000
setenv fdt_addr_r 0x43000000
setenv ramdisk_addr_r 0x44300000
fi
if test -n "${console}"; then
setenv bootargs "${bootargs} console=${console}"
fi
setenv bootargs ${bootargs} quiet
if test -z "${image_locations}"; then
setenv image_locations ${prefix}
fi
if test -z "${image_locations}"; then
setenv image_locations /boot/ /
fi
if test -z "${fk_kvers}"; then
setenv fk_kvers '5.16.0-4-armmp-lpae'
fi
if test -n "${fdtfile}"; then
setenv fdtpath dtbs/${fk_kvers}/${fdtfile}
else
setenv fdtpath dtb-${fk_kvers}
fi
for pathprefix in ${image_locations}
do
if test -e ${device} ${partition} ${pathprefix}vmlinuz-${fk_kvers}
then
load ${device} ${partition} ${kernel_addr_r}
${pathprefix}vmlinuz-${fk_kvers} \
&& load ${device} ${partition} ${fdt_addr_r} ${pathprefix}${fdtpath} \
&& load ${device} ${partition} ${ramdisk_addr_r}
${pathprefix}initrd.img-${fk_kvers} \
&& echo "Booting Debian ${fk_kvers} from ${device} ${partition}..." \
&& bootz ${kernel_addr_r} ${ramdisk_addr_r}:${filesize} ${fdt_addr_r}
fi
done
Nothing special done here.
U-Boot 2022.04 (Apr 26 2022 - 16:02:27 +0000) Allwinner Technology
=> echo $boot_targets
fel mmc0 usb0 pxe dhcp
=> dm tree
Class Index Probed Driver Name
-----------------------------------------------------------
root 0 [ + ] root_driver root_driver
video 0 [ ] sunxi_de2 |-- sunxi_de2
display 0 [ ] sunxi_dw_hdmi |-- sunxi_dw_hdmi
simple_bus 0 [ + ] simple_bus |-- soc
mmc 0 [ + ] sunxi_mmc | |-- mmc@1c0f000
blk 0 [ + ] mmc_blk | | `-- m...@1c0f000.blk
phy 0 [ + ] sun4i_usb_phy | |-- phy@1c19400
usb 0 [ + ] ehci_generic | |-- usb@1c1a000
usb_hub 0 [ + ] usb_hub | | `-- usb_hub
usb 1 [ + ] ohci_generic | |-- usb@1c1a400
usb_hub 1 [ + ] usb_hub | | `-- usb_hub
usb 2 [ + ] ehci_generic | |-- usb@1c1b000
usb_hub 2 [ + ] usb_hub | | `-- usb_hub
usb 3 [ + ] ohci_generic | |-- usb@1c1b400
usb_hub 3 [ + ] usb_hub | | `-- usb_hub
usb 4 [ + ] ehci_generic | |-- usb@1c1c000
usb_hub 4 [ + ] usb_hub | | `-- usb_hub
usb_mass_s 0 [ + ] usb_mass_storage | | `--
usb_mass_storage
blk 1 [ ] usb_storage_blk | | `--
usb_mass_storage.lun0
usb 5 [ + ] ohci_generic | |-- usb@1c1c400
usb_hub 5 [ + ] usb_hub | | `-- usb_hub
usb 6 [ + ] ehci_generic | |-- usb@1c1d000
usb_hub 6 [ + ] usb_hub | | `-- usb_hub
usb 7 [ + ] ohci_generic | |-- usb@1c1d400
usb_hub 7 [ + ] usb_hub | | `-- usb_hub
clk 0 [ + ] sun8i_h3_ccu | |-- clock@1c20000
reset 0 [ + ] sunxi_reset | | `-- reset
gpio 0 [ + ] gpio_sunxi | |-- pinctrl@1c20800
gpio 1 [ + ] gpio_sunxi | | |-- PA
gpio 2 [ + ] gpio_sunxi | | |-- PB
gpio 3 [ + ] gpio_sunxi | | |-- PC
gpio 4 [ + ] gpio_sunxi | | |-- PD
gpio 5 [ + ] gpio_sunxi | | |-- PE
gpio 6 [ + ] gpio_sunxi | | |-- PF
gpio 7 [ + ] gpio_sunxi | | |-- PG
gpio 8 [ + ] gpio_sunxi | | |-- PH
gpio 9 [ + ] gpio_sunxi | | `-- PI
ethernet 0 [ + ] eth_sun8i_emac | |-- ethernet@1c30000
watchdog 0 [ + ] sunxi_wdt | |-- watchdog@1c20ca0
sysreset 0 [ ] wdt_reboot | | `-- watchdog@1c20ca0
serial 0 [ + ] ns16550_serial | |-- serial@1c28000
clk 1 [ + ] clk_sun6i_rtc | |-- rtc@1f00000
clk 2 [ ] sun6i_a31_r_ccu | |-- clock@1f01400
reset 1 [ ] sunxi_reset | | `-- reset
i2c 0 [ ] i2c_mvtwsi | |-- i2c@1f02400
gpio 10 [ + ] gpio_sunxi | `-- pinctrl@1f02c00
gpio 11 [ + ] gpio_sunxi | `-- PL
clk 3 [ + ] fixed_clock |-- osc24M_clk
clk 4 [ ] fixed_clock `-- osc32k_clk
U-Boot 2022.07-rc1 (Apr 26 2022 - 07:00:52 +0000) Allwinner Technology
=> echo $boot_targets
fel mmc0 usb0 pxe dhcp
=> dm tree
Class Index Probed Driver Name
-----------------------------------------------------------
root 0 [ + ] root_driver root_driver
video 0 [ ] sunxi_de2 |-- sunxi_de2
display 0 [ ] sunxi_dw_hdmi |-- sunxi_dw_hdmi
simple_bus 0 [ + ] simple_bus |-- soc
mmc 0 [ + ] sunxi_mmc | |-- mmc@1c0f000
blk 0 [ + ] mmc_blk | | |-- m...@1c0f000.blk
A block device detected here.
partition 0 [ + ] blk_partition | | | |--
m...@1c0f000.blk:1
partition 1 [ + ] blk_partition | | | |--
m...@1c0f000.blk:2
partition 2 [ + ] blk_partition | | | `--
m...@1c0f000.blk:3
Apparently, there are three partition devices,
then we should definitely have corresponding efi_disk objects
as an efi_loader hook is registered against *POST_PROBE* event
(of a *block* device).
In my patch c822c1a50bd7 ("mmc: call device_probe() after scanning"),
device_probe() has already been installed to mmc_blk_probe().
Thinking of those circumstances, the natural guess is a *probe* function
for "m...@1c0f000.blk" device has never been called in your use case
(even when loading an image from a specific partition, /boot/efi?).
To confirm this, you may simply try the followings:
=> mmc list
...
=> mmc dev 0 (<- the device number from 'mmc list')
=> efi devices
Then you will find three more efi_disk objects now that the parent
block device is *probed*.
bootdev 0 [ ] mmc_bootdev | | `--
mmc@1c0f000.bootdev
phy 0 [ + ] sun4i_usb_phy | |-- phy@1c19400
usb 0 [ + ] ehci_generic | |-- usb@1c1a000
usb_hub 0 [ + ] usb_hub | | `-- usb_hub
usb 1 [ + ] ohci_generic | |-- usb@1c1a400
usb_hub 1 [ + ] usb_hub | | `-- usb_hub
usb 2 [ + ] ehci_generic | |-- usb@1c1b000
usb_hub 2 [ + ] usb_hub | | `-- usb_hub
usb 3 [ + ] ohci_generic | |-- usb@1c1b400
usb_hub 3 [ + ] usb_hub | | `-- usb_hub
usb 4 [ + ] ehci_generic | |-- usb@1c1c000
usb_hub 4 [ + ] usb_hub | | `-- usb_hub
usb_mass_s 0 [ + ] usb_mass_storage | | `--
usb_mass_storage
blk 1 [ + ] usb_storage_blk | | |--
usb_mass_storage.lun0
partition 3 [ + ] blk_partition | | | `--
usb_mass_storage.lun0:1
bootdev 3 [ ] usb_bootdev | | `--
usb_mass_storage.lun0.bootdev
usb 5 [ + ] ohci_generic | |-- usb@1c1c400
usb_hub 5 [ + ] usb_hub | | `-- usb_hub
usb 6 [ + ] ehci_generic | |-- usb@1c1d000
usb_hub 6 [ + ] usb_hub | | `-- usb_hub
usb 7 [ + ] ohci_generic | |-- usb@1c1d400
usb_hub 7 [ + ] usb_hub | | `-- usb_hub
clk 0 [ + ] sun8i_h3_ccu | |-- clock@1c20000
reset 0 [ + ] sunxi_reset | | `-- reset
pinctrl 0 [ + ] sunxi-pinctrl | |-- pinctrl@1c20800
gpio 0 [ + ] gpio_sunxi | | |-- pinctrl@1c20800
gpio 1 [ + ] gpio_sunxi | | | |-- PA
gpio 2 [ + ] gpio_sunxi | | | |-- PB
gpio 3 [ + ] gpio_sunxi | | | |-- PC
gpio 4 [ + ] gpio_sunxi | | | |-- PD
gpio 5 [ + ] gpio_sunxi | | | |-- PE
gpio 6 [ + ] gpio_sunxi | | | |-- PF
gpio 7 [ + ] gpio_sunxi | | | `-- PG
pinconfig 0 [ ] pinconfig | | |-- csi-pins
pinconfig 1 [ ] pinconfig | | |-- emac-rgmii-pins
pinconfig 2 [ ] pinconfig | | |-- i2c0-pins
pinconfig 3 [ ] pinconfig | | |-- i2c1-pins
pinconfig 4 [ ] pinconfig | | |-- i2c2-pins
pinconfig 5 [ + ] pinconfig | | |-- mmc0-pins
pinconfig 6 [ ] pinconfig | | |-- mmc1-pins
pinconfig 7 [ ] pinconfig | | |-- mmc2-8bit-pins
pinconfig 8 [ ] pinconfig | | |-- spdif-tx-pin
pinconfig 9 [ ] pinconfig | | |-- spi0-pins
pinconfig 10 [ ] pinconfig | | |-- spi1-pins
pinconfig 11 [ + ] pinconfig | | |-- uart0-pa-pins
pinconfig 12 [ ] pinconfig | | |-- uart1-pins
pinconfig 13 [ ] pinconfig | | |--
uart1-rts-cts-pins
pinconfig 14 [ ] pinconfig | | |-- uart2-pins
pinconfig 15 [ ] pinconfig | | |--
uart2-rts-cts-pins
pinconfig 16 [ ] pinconfig | | |-- uart3-pins
pinconfig 17 [ ] pinconfig | | |--
uart3-rts-cts-pins
pinconfig 18 [ ] pinconfig | | |-- ahci_pwr_pin@0
pinconfig 19 [ ] pinconfig | | |-- usb0_vbus_pin@0
pinconfig 20 [ ] pinconfig | | |-- usb1_vbus_pin@0
pinconfig 21 [ ] pinconfig | | `-- usb2_vbus_pin@0
ethernet 0 [ + ] eth_sun8i_emac | |-- ethernet@1c30000
bootdev 1 [ ] eth_bootdev | | `--
ethernet@1c30000.bootdev
watchdog 0 [ + ] sunxi_wdt | |-- watchdog@1c20ca0
sysreset 0 [ ] wdt_reboot | | `-- watchdog@1c20ca0
serial 0 [ + ] ns16550_serial | |-- serial@1c28000
clk 1 [ + ] clk_sun6i_rtc | |-- rtc@1f00000
clk 2 [ + ] sun6i_a31_r_ccu | |-- clock@1f01400
reset 1 [ ] sunxi_reset | | `-- reset
i2c 0 [ ] i2c_mvtwsi | |-- i2c@1f02400
pinctrl 1 [ + ] sunxi-pinctrl | `-- pinctrl@1f02c00
gpio 8 [ + ] gpio_sunxi | |-- pinctrl@1f02c00
gpio 9 [ + ] gpio_sunxi | | `-- PL
pinconfig 22 [ ] pinconfig | |-- r-ir-rx-pin
pinconfig 23 [ ] pinconfig | |-- r-i2c-pins
pinconfig 24 [ ] pinconfig | `-- r-pwm-pin
clk 3 [ + ] fixed_clock |-- osc24M_clk
clk 4 [ ] fixed_clock |-- osc32k_clk
bootstd 0 [ ] bootstd_drv `-- bootstd
bootmeth 0 [ ] bootmeth_distro |-- distro
bootmeth 1 [ ] bootmeth_efi |-- efi
bootmeth 2 [ ] bootmeth_pxe |-- pxe
bootdev 2 [ ] system_bootdev `-- system-bootdev
grub rescue> ls
(hd0)
Grub does not see any partition at all.
Loading a device from a partition does not create a handle for the device:
Actually, loading an image does *not* invoke a probe function at all
under the current implementation (of either "part" command,
scan_dev_for_boot_part or even mmc drivers?).
We call efi_disk_init() after the MMC device is probed. Therefore
probing of the MCC device does not trigger EVT_DM_POST_PROBE.
We have to move the efi_disk_init() call before initr_dm().
[PATCH 1/1] efi_loader: call efi_init_early() earlier
https://lists.denx.de/pipermail/u-boot/2022-April/482701.html
With the patch GRUB now sees the MMC device but it is still not seeing
the partitions:
grub rescue> ls
(hd0) (hd1)
This is strange because devices and protocols look rather normal now:
=> dm tree
Class Index Probed Driver Name
-----------------------------------------------------------
root 0 [ + ] root_driver root_driver
simple_bus 0 [ + ] simple_bus |-- soc
mmc 0 [ + ] sunxi_mmc | |-- mmc@1c0f000
blk 0 [ + ] mmc_blk | | |-- m...@1c0f000.blk
partition 0 [ + ] blk_partition | | | |--
m...@1c0f000.blk:1
partition 1 [ + ] blk_partition | | | |--
m...@1c0f000.blk:2
partition 2 [ + ] blk_partition | | | `--
m...@1c0f000.blk:3
usb 4 [ + ] ehci_generic | |-- usb@1c1c000
usb_hub 4 [ + ] usb_hub | | `-- usb_hub
usb_mass_s 0 [ + ] usb_mass_storage | | `--
usb_mass_storage
blk 1 [ + ] usb_storage_blk | | |--
usb_mass_storage.lun0
partition 3 [ + ] blk_partition | | | `--
usb_mass_storage.lun0:1
bootdev 3 [ ] usb_bootdev | | `--
usb_mass_storage.lun0.bootdev
=> efidebug devices
Device Device Path
======== ====================
79f701e8 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)
7dffc7ec /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Uart(0,0,D,D)
79f70cd8 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(0)
79f70de0
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(0)/HD(1,MBR,0xb6b4facb,0x800,0x200000)
79f711b0
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(0)/HD(2,MBR,0xb6b4facb,0x200800,0x200000)
79f71538
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(0)/HD(3,MBR,0xb6b4facb,0x400800,0x379f800)
79f811b8
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x1)/UsbClass(0x781,0x5571,0x0,0x0,0x0)
79f81260
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x1)/UsbClass(0x781,0x5571,0x0,0x0,0x0)/HD(1,MBR,0x0c449046,0x800,0x800)
79fdd748 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/MAC(0281431d5371,1)
=> efidebug dh
Handle Protocols
======== ====================
79f701e8 Device Path, Device Path To Text, Device Path Utilities,
Device-Tree Fixup, Unicode Collation 2, HII String, HII Database, Simple
Text Output, Simple Text Input, Simple Text Input Ex
7dffc7ec Device Path
79f70cd8 Device Path, Block IO
79f70de0 Device Path, Block IO, System Partition, Simple File System
79f711b0 Device Path, Block IO, Simple File System
79f71538 Device Path, Block IO, Simple File System
79f811b8 Device Path, Block IO
79f81260 Device Path, Block IO, System Partition, Simple File System
79f84978 Driver Binding
79fdd748 Simple Network, Device Path, PXE Base Code
This is the console log *before* the patch:
U-Boot 2022.07-rc1-00082-g8b2b125e95-dirty (Apr 28 2022 - 06:01:10
+0000) Allwinner Technology
CPU: Allwinner H3 (SUN8I 1680)
Model: Xunlong Orange Pi PC
DRAM: 1 GiB
drivers/mmc/sunxi_mmc.c(723)sunxi_mmc_bind:
sunxi_set_gate: (CLK#54) unhandled
Core: 70 devices, 20 uclasses, devicetree: separate
WDT: Not starting watchdog@1c20ca0
MMC: drivers/mmc/sunxi_mmc.c(667)sunxi_mmc_probe:
mmc@1c0f000: 0
Loading Environment from FAT... drivers/mmc/mmc-uclass.c(487)mmc_blk_probe:
drivers/block/blk-uclass.c(746)blk_post_probe:
drivers/block/blk-uclass.c(752)blk_post_probe:
disk/part.c(242)part_init:
part_init: try 'EFI': ret=-1
part_init: try 'DOS': ret=0
part_create_block_devices: 3 partitions found in m...@1c0f000.blk
disk/part.c(242)part_init:
part_init: try 'EFI': ret=-1
part_init: try 'DOS': ret=0
Unable to read "uboot.env" from mmc0:1...
In: serial
Out: serial
Err: serial
Net: phy interface1
eth0: ethernet@1c30000
lib/efi_loader/efi_disk.c(739)efi_disk_init:
starting USB...
Bus usb@1c1a000: USB EHCI 1.00
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
Bus usb@1c1a400: USB OHCI 1.0
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
Bus usb@1c1b000: lib/efi_loader/efi_disk.c(622)efi_disk_probe:
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
sunxi_set_gate: (CLK#9) unhandled
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
USB EHCI 1.00
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
Bus usb@1c1b400: USB OHCI 1.0
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
Bus usb@1c1c000: USB EHCI 1.00
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
Bus usb@1c1c400: USB OHCI 1.0
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
Bus usb@1c1d000: USB EHCI 1.00
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
Bus usb@1c1d400: USB OHCI 1.0
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
scanning bus usb@1c1a000 for devices...
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
1 USB Device(s) found
scanning bus usb@1c1a400 for devices...
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
1 USB Device(s) found
scanning bus usb@1c1b000 for devices...
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
1 USB Device(s) found
scanning bus usb@1c1b400 for devices...
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
1 USB Device(s) found
scanning bus usb@1c1c000 for devices...
drivers/block/blk-uclass.c(746)blk_post_probe:
drivers/block/blk-uclass.c(752)blk_post_probe:
disk/part.c(242)part_init:
part_init: try 'EFI': ret=-1
part_init: try 'DOS': ret=0
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
part_create_block_devices: 1 partitions found in usb_mass_storage.lun0
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
lib/efi_loader/efi_disk.c(568)efi_disk_create_part:
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
2 USB Device(s) found
scanning bus usb@1c1c400 for devices...
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
1 USB Device(s) found
scanning bus usb@1c1d000 for devices...
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
1 USB Device(s) found
scanning bus usb@1c1d400 for devices...
lib/efi_loader/efi_disk.c(622)efi_disk_probe:
1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
Best regards
Heinrich
I think that this is weird as the purpose of "probe" is to activate
the device, or "probe - make a device ready for use" according to
doc/develop/driver-model/design.rst
So my conclusion is that the current implementation has already broken
the driver model even before my patch was applied.
-> Simon, you should have a comment here?
That said, fixing a problem is a different matter.
Probably, we will have to modify "part" command or mmc drivers themselves.
Can you figure out an easy way to reproduce the issue?
(either on sandbox or qemu-arm)
Otherwise, it is difficult for me to investigate it.
-Takahiro Akashi
-Takahiro Akashi
=> efidebug devices
** Unable to read file ubootefi.var **
Failed to load EFI variables
Device Device Path
======== ====================
79f80f08 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)
7dffc7ec /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Uart(0,0,D,D)
79f7f1f8
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x1)/UsbClass(0x781,0x5571,0x0,0x0,0x0)
79f7f2a0
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x1)/UsbClass(0x781,0x5571,0x0,0x0,0x0)/HD(1,MBR,0x0c449046,0x800,0x800)
79fdc188 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/MAC(0281431d5371,1)
=> bootefi $kernel_addr_r
Booting /helloworld.efi
invalid image type: 0
Hello, world!
=> efidebug devices
Device Device Path
======== ====================
79f80f08 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)
7dffc7ec /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Uart(0,0,D,D)
79f7f1f8
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x1)/UsbClass(0x781,0x5571,0x0,0x0,0x0)
79f7f2a0
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x1)/UsbClass(0x781,0x5571,0x0,0x0,0x0)/HD(1,MBR,0x0c449046,0x800,0x800)
79fdc188 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/MAC(0281431d5371,1)
=>
So the current state is a complete mess.
Best regards
Heinrich
