Adding Matthias as the RPi maintainer. There was also this patch series which fixed it and a few other things from the firmware DT [1] which is likely a better fix TBH.
Either way Matthias can we get one of these upstream as even the RPi4 Model B has moved to the newer rev of the SoCs so it's not a nice experience for users if they're not aware of the differences/problems. Peter [1] https://lists.denx.de/pipermail/u-boot/2022-August/491455.html On Wed, Oct 26, 2022 at 12:23 PM Jian-Hong Pan <j...@endlessos.org> wrote: > > From: Ilya Katsnelson <m...@0upti.me> > > The RPi firmware adjusts the onboard eMMC controller's DMA mapping > ranges of the FDT for each BCM2711 SoC revisions on the Pi 4 and RPi 400 > automatically. > > If the following kernel does not boot with the correct eMMC controller's > DMA mapping ranges, the system on the SD card will boot failed and show > these error messages: > > mmc1: invalid bus width > mmc1: error -22 whilst initialising SD card > > This patch carries the adjustment from RPi firmware to the new loaded > FDT for the following kernel. > > Link: https://lists.denx.de/pipermail/u-boot/2021-September/462006.html > Fixed: https://bugzilla.kernel.org/show_bug.cgi?id=213753 > Signed-off-by: Ilya Katsnelson <m...@0upti.me> > Signed-off-by: Jian-Hong Pan <j...@endlessos.org> > --- > The code of this patch comes from "[RFC PATCH] rpi: copy the EMMC > controller configuration from firmware-supplied DT" [1] basically. > I only add the message and some modifcation: > > * Fix the build failed error: > board/raspberrypi/rpi/rpi.c: In function 'copy_emmc_config': > board/raspberrypi/rpi/rpi.c:553:9: warning: dereferencing 'void *' pointer > 553 | *fw_value = fdt_getprop(fw_fdt, fw_emmc_node, "dma-ranges", > &length); > | ^~~~~~~~~ > board/raspberrypi/rpi/rpi.c:553:19: error: invalid use of void expression > 553 | *fw_value = fdt_getprop(fw_fdt, fw_emmc_node, "dma-ranges", > &length); > | ^ > make[1]: *** [scripts/Makefile.build:258: board/raspberrypi/rpi/rpi.o] Error 1 > > * Replace "EMMC" to "eMMC". > > * Replace the printf with log_[levels]. > > So, I keep "Ilya Katsnelson <m...@0upti.me>" as the author. > > [1]: https://lists.denx.de/pipermail/u-boot/2021-September/462006.html > > board/raspberrypi/rpi/rpi.c | 63 +++++++++++++++++++++++++++++++++++++ > 1 file changed, 63 insertions(+) > > diff --git a/board/raspberrypi/rpi/rpi.c b/board/raspberrypi/rpi/rpi.c > index 00afb352bd..d7ff8e269e 100644 > --- a/board/raspberrypi/rpi/rpi.c > +++ b/board/raspberrypi/rpi/rpi.c > @@ -504,6 +504,67 @@ void *board_fdt_blob_setup(int *err) > return (void *)fw_dtb_pointer; > } > > +void copy_emmc_config(void *our_fdt) > +{ > + /* > + * As of 2021-09-28, the Pi 4 has two different revisions, one using a > + * B0 stepping of the BCM2711 SoC, and one using a C0 stepping. > + * > + * The two SoC versions have different, incompatible DMA mappings for > + * the on-board eMMC controller, which would normally make them > require > + * two different DTs. > + * > + * Unfortunately for us, the different revisions don't actually _use_ > + * different DTs - instead, the proprietary stage0 bootloader reads > the DT, > + * patches it in-memory, then passes the corrected DT to the OS. > + * > + * In our case, the OS is actually U-Boot, and U-Boot can choose to > + * completely disregard the firmware-supplied DT and load a custom one > + * instead, which is used by, e.g., NixOS. > + * > + * When that happens, the DT patches applied by the firmware are also > + * thrown out, which leads to BCM2711C0 boards being unable to boot > + * due to them trying to use the hardcoded DMA mappings in the DT > + * (which are for the B0 revision). > + * > + * Work around that by manually copying the DMA region setup from the > + * firmware-provided DT into whatever DT we're actually being asked > + * to load. > + */ > + void *fw_fdt = (void *)fw_dtb_pointer; > + int fw_emmc_node; > + int our_emmc_node; > + int length; > + const void *fw_value; > + int result; > + > + fw_emmc_node = fdt_path_offset(fw_fdt, "emmc2bus"); > + if (fw_emmc_node < 0) { > + log_info("RPi: Failed to find eMMC config in FW DT: %d\n", > fw_emmc_node); > + return; > + } > + > + our_emmc_node = fdt_path_offset(our_fdt, "emmc2bus"); > + if (our_emmc_node < 0) { > + log_info("RPi: Failed to find eMMC config in our DT: %d\n", > our_emmc_node); > + return; > + } > + > + fw_value = fdt_getprop(fw_fdt, fw_emmc_node, "dma-ranges", &length); > + if (!fw_value) { > + log_info("RPi: Failed to get eMMC DMA ranges property from FW > DT: %d\n", length); > + return; > + } > + > + result = fdt_setprop(our_fdt, our_emmc_node, "dma-ranges", fw_value, > length); > + if (result != 0) { > + log_warning("RPi: Failed to set eMMC DMA ranges property in > our DT: %d\n", result); > + return; > + } > + > + log_debug("RPi: successfully copied FW DT eMMC configuration to our > DT!\n"); > +} > + > int ft_board_setup(void *blob, struct bd_info *bd) > { > int node; > @@ -518,5 +579,7 @@ int ft_board_setup(void *blob, struct bd_info *bd) > EFI_RESERVED_MEMORY_TYPE); > #endif > > + copy_emmc_config(blob); > + > return 0; > } > -- > 2.38.1 >