This converts the following to Kconfig:
CONFIG_SYS_FPGA_CHECK_BUSY
Signed-off-by: Tom Rini <tr...@konsulko.com>
---
drivers/fpga/Kconfig | 4 ++++
drivers/fpga/spartan2.c | 2 --
drivers/fpga/spartan3.c | 2 --
drivers/fpga/virtex2.c | 7 ++-----
4 files changed, 6 insertions(+), 9 deletions(-)
diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
index 813d6a836d97..11b742eeebfe 100644
--- a/drivers/fpga/Kconfig
+++ b/drivers/fpga/Kconfig
@@ -96,6 +96,10 @@ config FPGA_VIRTEX2
Enable Virtex-II FPGA driver for loading in BIT format. This driver
also supports many newer Xilinx FPGA families.
+config SYS_FPGA_CHECK_BUSY
+ bool "Perform busy check during load from FPGA"
+ depends on FPGA_SPARTAN2 || FPGA_SPARTAN3 || FPGA_VIRTEX2
+
config FPGA_ZYNQPL
bool "Enable Xilinx FPGA for Zynq"
depends on ARCH_ZYNQ
diff --git a/drivers/fpga/spartan2.c b/drivers/fpga/spartan2.c
index 57a4532f736e..68971d934702 100644
--- a/drivers/fpga/spartan2.c
+++ b/drivers/fpga/spartan2.c
@@ -10,8 +10,6 @@
#include <log.h>
#include <spartan2.h> /* Spartan-II device family */
-#undef CONFIG_SYS_FPGA_CHECK_BUSY
-
/* Note: The assumption is that we cannot possibly run fast enough to
* overrun the device (the Slave Parallel mode can free run at 50MHz).
* If there is a need to operate slower, define CONFIG_FPGA_DELAY in
diff --git a/drivers/fpga/spartan3.c b/drivers/fpga/spartan3.c
index fdec89bb815f..1d5073cb59d4 100644
--- a/drivers/fpga/spartan3.c
+++ b/drivers/fpga/spartan3.c
@@ -15,8 +15,6 @@
#include <log.h>
#include <spartan3.h> /* Spartan-II device family */
-#undef CONFIG_SYS_FPGA_CHECK_BUSY
-
/* Note: The assumption is that we cannot possibly run fast enough to
* overrun the device (the Slave Parallel mode can free run at 50MHz).
* If there is a need to operate slower, define CONFIG_FPGA_DELAY in
diff --git a/drivers/fpga/virtex2.c b/drivers/fpga/virtex2.c
index 8871deaea6f6..ed2a4163f6eb 100644
--- a/drivers/fpga/virtex2.c
+++ b/drivers/fpga/virtex2.c
@@ -21,14 +21,11 @@
#include <linux/delay.h>
/*
- * If the SelectMap interface can be overrun by the processor, define
- * CONFIG_SYS_FPGA_CHECK_BUSY and/or CONFIG_FPGA_DELAY in the board
+ * If the SelectMap interface can be overrun by the processor, enable
+ * CONFIG_SYS_FPGA_CHECK_BUSY and/or define CONFIG_FPGA_DELAY in the board
* configuration file and add board-specific support for checking BUSY status.
* By default, assume that the SelectMap interface cannot be overrun.
*/
-#ifndef CONFIG_SYS_FPGA_CHECK_BUSY
-#undef CONFIG_SYS_FPGA_CHECK_BUSY
-#endif
#ifndef CONFIG_FPGA_DELAY
#define CONFIG_FPGA_DELAY()
--
2.25.1
