On 2023/2/17 19:58, Jagan Teki wrote:
From: Manoj Sai <abbaraju.manoj...@amarulasolutions.com>
=> usb start
starting USB...
Bus usb@fd000000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@fd800000: USB EHCI 1.00
scanning bus usb@fd000000 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning bus usb@fd800000 for devices... 4 USB Device(s) found
scanning usb for storage devices... 2 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 224mA)
SanDisk Dual Drive 04019c9b2e1a58f24ee318c3c123aa5
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)
| USB 2.0 Hub
|
+-3 Mass Storage (480 Mb/s, 500mA)
| JetFlash Mass Storage Device 19M7I4ZQFTSC08SU
|
+-4 Human Interface (12 Mb/s, 98mA)
Logitech USB Receiver
Co-developed-by: Suniel Mahesh <su...@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <su...@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manoj...@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.y...@rock-chips.com>
Thanks,
- Kever
---
configs/radxa-cm3-io-rk3566_defconfig | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/configs/radxa-cm3-io-rk3566_defconfig
b/configs/radxa-cm3-io-rk3566_defconfig
index a79d9b25e3..2100cf2cb2 100644
--- a/configs/radxa-cm3-io-rk3566_defconfig
+++ b/configs/radxa-cm3-io-rk3566_defconfig
@@ -38,6 +38,7 @@ CONFIG_SPL_STACK_R=y
CONFIG_SPL_ATF=y
CONFIG_CMD_GPT=y
CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
# CONFIG_SPL_DOS_PARTITION is not set
CONFIG_SPL_OF_CONTROL=y
@@ -57,10 +58,20 @@ CONFIG_MMC_SDHCI_SDMA=y
CONFIG_MMC_SDHCI_ROCKCHIP=y
CONFIG_ETH_DESIGNWARE=y
CONFIG_GMAC_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
CONFIG_REGULATOR_PWM=y
+CONFIG_DM_REGULATOR_GPIO=y
CONFIG_PWM_ROCKCHIP=y
CONFIG_SPL_RAM=y
CONFIG_BAUDRATE=1500000
CONFIG_DEBUG_UART_SHIFT=2
CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
CONFIG_ERRNO_STR=y
