This is taken from Linux kernel 5.17, and contains just bare minimum
functionality: CPU, UART and system timer.
Additional functionality (from newer kernel versions) will be added
later. Note that the Linux side is under active development.
Signed-off-by: Ralph Siemsen <ralph.siem...@linaro.org>
---
The following changes were made, compared with Linux 5.17:
1) Add node for system controller registers.
Declare it as syscon to provide a regmap interface.
2) In the clock controller node (renesas,r9a06g032-sysctrl),
replace regs with regmap.
3) Add syscon-reset node, making use of the syscon regmap.
4) Add syscon phandle to ddrctrl. Used for checking h/w version.
5) Simplify the compatible string for all the UARTS, as per
doc/device-tree-bindings/serial/snps-dw-apb-uart.txt
I could not find a way to avoid 1) and 2). Putting "syscon" in the
compatible string for the clock controller leads to a catch-22,
where the driver fails to initialize, and then boot hangs.
(no changes since v3)
Changes in v3:
- add syscon phandle to ddrctl
- simplify UART compatible strings
arch/arm/dts/r9a06g032.dtsi | 226 ++++++++++++++++++
include/dt-bindings/clock/r9a06g032-sysctrl.h | 148 ++++++++++++
2 files changed, 374 insertions(+)
create mode 100644 arch/arm/dts/r9a06g032.dtsi
create mode 100644 include/dt-bindings/clock/r9a06g032-sysctrl.h
diff --git a/arch/arm/dts/r9a06g032.dtsi b/arch/arm/dts/r9a06g032.dtsi
new file mode 100644
index 0000000000..e0ddffb074
--- /dev/null
+++ b/arch/arm/dts/r9a06g032.dtsi
@@ -0,0 +1,226 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Base Device Tree Source for the Renesas RZ/N1D (R9A06G032)
+ *
+ * Copyright (C) 2018 Renesas Electronics Europe Limited
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/r9a06g032-sysctrl.h>
+
+/ {
+ compatible = "renesas,r9a06g032";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0>;
+ clocks = <&sysctrl R9A06G032_CLK_A7MP>;
+ };
+
+ cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <1>;
+ clocks = <&sysctrl R9A06G032_CLK_A7MP>;
+ enable-method = "renesas,r9a06g032-smp";
+ cpu-release-addr = <0 0x4000c204>;
+ };
+ };
+
+ ext_jtag_clk: extjtagclk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ };
+
+ ext_mclk: extmclk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <40000000>;
+ };
+
+ ext_rgmii_ref: extrgmiiref {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ };
+
+ ext_rtc_clk: extrtcclk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&gic>;
+ ranges;
+
+ plat_regs: system-controller@4000c000 {
+ compatible = "syscon";
+ reg = <0x4000c000 0x1000>;
+ u-boot,dm-pre-reloc;
+ };
+
+ sysctrl: clock {
+ compatible = "renesas,r9a06g032-sysctrl";
+ #clock-cells = <1>;
+ regmap = <&plat_regs>;
+ u-boot,dm-pre-reloc;
+
+ clocks = <&ext_mclk>, <&ext_rtc_clk>,
+ <&ext_jtag_clk>, <&ext_rgmii_ref>;
+ clock-names = "mclk", "rtc", "jtag", "rgmii_ref_ext";
+ };
+
+ ddrctrl: memory-controller@4000d000 {
+ compatible = "cadence,ddr-ctrl";
+ reg = <0x4000d000 0x1000>, <0x4000e000 0x100>;
+ reg-names = "ddrc", "phy";
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sysctrl R9A06G032_CLK_DDRC>, <&sysctrl
R9A06G032_HCLK_DDRC>;
+ clock-names = "clk_ddrc", "hclk_ddrc";
+ syscon = <&plat_regs>;
+ status = "disabled";
+ };
+
+ uart0: serial@40060000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x40060000 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&sysctrl R9A06G032_CLK_UART0>, <&sysctrl
R9A06G032_HCLK_UART0>;
+ clock-names = "baudclk", "apb_pclk";
+ status = "disabled";
+ };
+
+ uart1: serial@40061000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x40061000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&sysctrl R9A06G032_CLK_UART1>, <&sysctrl
R9A06G032_HCLK_UART1>;
+ clock-names = "baudclk", "apb_pclk";
+ status = "disabled";
+ };
+
+ uart2: serial@40062000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x40062000 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&sysctrl R9A06G032_CLK_UART2>, <&sysctrl
R9A06G032_HCLK_UART2>;
+ clock-names = "baudclk", "apb_pclk";
+ status = "disabled";
+ };
+
+ uart3: serial@50000000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x50000000 0x400>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&sysctrl R9A06G032_CLK_UART3>, <&sysctrl
R9A06G032_HCLK_UART3>;
+ clock-names = "baudclk", "apb_pclk";
+ status = "disabled";
+ };
+
+ uart4: serial@50001000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x50001000 0x400>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&sysctrl R9A06G032_CLK_UART4>, <&sysctrl
R9A06G032_HCLK_UART4>;
+ clock-names = "baudclk", "apb_pclk";
+ status = "disabled";
+ };
+
+ uart5: serial@50002000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x50002000 0x400>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&sysctrl R9A06G032_CLK_UART5>, <&sysctrl
R9A06G032_HCLK_UART5>;
+ clock-names = "baudclk", "apb_pclk";
+ status = "disabled";
+ };
+
+ uart6: serial@50003000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x50003000 0x400>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&sysctrl R9A06G032_CLK_UART6>, <&sysctrl
R9A06G032_HCLK_UART6>;
+ clock-names = "baudclk", "apb_pclk";
+ status = "disabled";
+ };
+
+ uart7: serial@50004000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x50004000 0x400>;
+ interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&sysctrl R9A06G032_CLK_UART7>, <&sysctrl
R9A06G032_HCLK_UART7>;
+ clock-names = "baudclk", "apb_pclk";
+ status = "disabled";
+ };
+
+ pinctrl: pinctrl@40067000 {
+ compatible = "renesas,r9a06g032-pinctrl",
"renesas,rzn1-pinctrl";
+ reg = <0x40067000 0x1000>, <0x51000000 0x480>;
+ clocks = <&sysctrl R9A06G032_HCLK_PINCONFIG>;
+ clock-names = "bus";
+ status = "disabled";
+ };
+
+ gic: interrupt-controller@44101000 {
+ compatible = "arm,gic-400", "arm,cortex-a7-gic";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = <0x44101000 0x1000>, /* Distributer */
+ <0x44102000 0x2000>, /* CPU interface */
+ <0x44104000 0x2000>, /* Virt interface control */
+ <0x44106000 0x2000>; /* Virt CPU interface */
+ interrupts =
+ <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_LEVEL_HIGH)>;
+ };
+ };
+
+ timer {
+ compatible = "arm,cortex-a7-timer",
+ "arm,armv7-timer";
+ interrupt-parent = <&gic>;
+ arm,cpu-registers-not-fw-configured;
+ always-on;
+ interrupts =
+ <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ reboot {
+ compatible = "syscon-reboot";
+ regmap = <&plat_regs>;
+ offset = <0x198>; /* sysctrl.RSTEN */
+ mask = <0x40>; /* bit 6 = SWRST_REQ */
+ value = <0x40>;
+ };
+};
diff --git a/include/dt-bindings/clock/r9a06g032-sysctrl.h
b/include/dt-bindings/clock/r9a06g032-sysctrl.h
new file mode 100644
index 0000000000..90c0f3dc1b
--- /dev/null
+++ b/include/dt-bindings/clock/r9a06g032-sysctrl.h
@@ -0,0 +1,148 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * R9A06G032 sysctrl IDs
+ *
+ * Copyright (C) 2018 Renesas Electronics Europe Limited
+ *
+ * Michel Pollet <michel.pol...@bp.renesas.com>, <buser...@gmail.com>
+ */
+
+#ifndef __DT_BINDINGS_R9A06G032_SYSCTRL_H__
+#define __DT_BINDINGS_R9A06G032_SYSCTRL_H__
+
+#define R9A06G032_CLK_PLL_USB 1
+#define R9A06G032_CLK_48 1 /* AKA CLK_PLL_USB */
+#define R9A06G032_MSEBIS_CLK 3 /* AKA CLKOUT_D16 */
+#define R9A06G032_MSEBIM_CLK 3 /* AKA CLKOUT_D16 */
+#define R9A06G032_CLK_DDRPHY_PLLCLK 5 /* AKA CLKOUT_D1OR2 */
+#define R9A06G032_CLK50 6 /* AKA CLKOUT_D20 */
+#define R9A06G032_CLK25 7 /* AKA CLKOUT_D40 */
+#define R9A06G032_CLK125 9 /* AKA CLKOUT_D8 */
+#define R9A06G032_CLK_P5_PG1 17 /* AKA DIV_P5_PG */
+#define R9A06G032_CLK_REF_SYNC 21 /* AKA DIV_REF_SYNC */
+#define R9A06G032_CLK_25_PG4 26
+#define R9A06G032_CLK_25_PG5 27
+#define R9A06G032_CLK_25_PG6 28
+#define R9A06G032_CLK_25_PG7 29
+#define R9A06G032_CLK_25_PG8 30
+#define R9A06G032_CLK_ADC 31
+#define R9A06G032_CLK_ECAT100 32
+#define R9A06G032_CLK_HSR100 33
+#define R9A06G032_CLK_I2C0 34
+#define R9A06G032_CLK_I2C1 35
+#define R9A06G032_CLK_MII_REF 36
+#define R9A06G032_CLK_NAND 37
+#define R9A06G032_CLK_NOUSBP2_PG6 38
+#define R9A06G032_CLK_P1_PG2 39
+#define R9A06G032_CLK_P1_PG3 40
+#define R9A06G032_CLK_P1_PG4 41
+#define R9A06G032_CLK_P4_PG3 42
+#define R9A06G032_CLK_P4_PG4 43
+#define R9A06G032_CLK_P6_PG1 44
+#define R9A06G032_CLK_P6_PG2 45
+#define R9A06G032_CLK_P6_PG3 46
+#define R9A06G032_CLK_P6_PG4 47
+#define R9A06G032_CLK_PCI_USB 48
+#define R9A06G032_CLK_QSPI0 49
+#define R9A06G032_CLK_QSPI1 50
+#define R9A06G032_CLK_RGMII_REF 51
+#define R9A06G032_CLK_RMII_REF 52
+#define R9A06G032_CLK_SDIO0 53
+#define R9A06G032_CLK_SDIO1 54
+#define R9A06G032_CLK_SERCOS100 55
+#define R9A06G032_CLK_SLCD 56
+#define R9A06G032_CLK_SPI0 57
+#define R9A06G032_CLK_SPI1 58
+#define R9A06G032_CLK_SPI2 59
+#define R9A06G032_CLK_SPI3 60
+#define R9A06G032_CLK_SPI4 61
+#define R9A06G032_CLK_SPI5 62
+#define R9A06G032_CLK_SWITCH 63
+#define R9A06G032_HCLK_ECAT125 65
+#define R9A06G032_HCLK_PINCONFIG 66
+#define R9A06G032_HCLK_SERCOS 67
+#define R9A06G032_HCLK_SGPIO2 68
+#define R9A06G032_HCLK_SGPIO3 69
+#define R9A06G032_HCLK_SGPIO4 70
+#define R9A06G032_HCLK_TIMER0 71
+#define R9A06G032_HCLK_TIMER1 72
+#define R9A06G032_HCLK_USBF 73
+#define R9A06G032_HCLK_USBH 74
+#define R9A06G032_HCLK_USBPM 75
+#define R9A06G032_CLK_48_PG_F 76
+#define R9A06G032_CLK_48_PG4 77
+#define R9A06G032_CLK_DDRPHY_PCLK 81 /* AKA CLK_REF_SYNC_D4 */
+#define R9A06G032_CLK_FW 81 /* AKA CLK_REF_SYNC_D4 */
+#define R9A06G032_CLK_CRYPTO 81 /* AKA CLK_REF_SYNC_D4 */
+#define R9A06G032_CLK_A7MP 84 /* AKA DIV_CA7 */
+#define R9A06G032_HCLK_CAN0 85
+#define R9A06G032_HCLK_CAN1 86
+#define R9A06G032_HCLK_DELTASIGMA 87
+#define R9A06G032_HCLK_PWMPTO 88
+#define R9A06G032_HCLK_RSV 89
+#define R9A06G032_HCLK_SGPIO0 90
+#define R9A06G032_HCLK_SGPIO1 91
+#define R9A06G032_RTOS_MDC 92
+#define R9A06G032_CLK_CM3 93
+#define R9A06G032_CLK_DDRC 94
+#define R9A06G032_CLK_ECAT25 95
+#define R9A06G032_CLK_HSR50 96
+#define R9A06G032_CLK_HW_RTOS 97
+#define R9A06G032_CLK_SERCOS50 98
+#define R9A06G032_HCLK_ADC 99
+#define R9A06G032_HCLK_CM3 100
+#define R9A06G032_HCLK_CRYPTO_EIP150 101
+#define R9A06G032_HCLK_CRYPTO_EIP93 102
+#define R9A06G032_HCLK_DDRC 103
+#define R9A06G032_HCLK_DMA0 104
+#define R9A06G032_HCLK_DMA1 105
+#define R9A06G032_HCLK_GMAC0 106
+#define R9A06G032_HCLK_GMAC1 107
+#define R9A06G032_HCLK_GPIO0 108
+#define R9A06G032_HCLK_GPIO1 109
+#define R9A06G032_HCLK_GPIO2 110
+#define R9A06G032_HCLK_HSR 111
+#define R9A06G032_HCLK_I2C0 112
+#define R9A06G032_HCLK_I2C1 113
+#define R9A06G032_HCLK_LCD 114
+#define R9A06G032_HCLK_MSEBI_M 115
+#define R9A06G032_HCLK_MSEBI_S 116
+#define R9A06G032_HCLK_NAND 117
+#define R9A06G032_HCLK_PG_I 118
+#define R9A06G032_HCLK_PG19 119
+#define R9A06G032_HCLK_PG20 120
+#define R9A06G032_HCLK_PG3 121
+#define R9A06G032_HCLK_PG4 122
+#define R9A06G032_HCLK_QSPI0 123
+#define R9A06G032_HCLK_QSPI1 124
+#define R9A06G032_HCLK_ROM 125
+#define R9A06G032_HCLK_RTC 126
+#define R9A06G032_HCLK_SDIO0 127
+#define R9A06G032_HCLK_SDIO1 128
+#define R9A06G032_HCLK_SEMAP 129
+#define R9A06G032_HCLK_SPI0 130
+#define R9A06G032_HCLK_SPI1 131
+#define R9A06G032_HCLK_SPI2 132
+#define R9A06G032_HCLK_SPI3 133
+#define R9A06G032_HCLK_SPI4 134
+#define R9A06G032_HCLK_SPI5 135
+#define R9A06G032_HCLK_SWITCH 136
+#define R9A06G032_HCLK_SWITCH_RG 137
+#define R9A06G032_HCLK_UART0 138
+#define R9A06G032_HCLK_UART1 139
+#define R9A06G032_HCLK_UART2 140
+#define R9A06G032_HCLK_UART3 141
+#define R9A06G032_HCLK_UART4 142
+#define R9A06G032_HCLK_UART5 143
+#define R9A06G032_HCLK_UART6 144
+#define R9A06G032_HCLK_UART7 145
+#define R9A06G032_CLK_UART0 146
+#define R9A06G032_CLK_UART1 147
+#define R9A06G032_CLK_UART2 148
+#define R9A06G032_CLK_UART3 149
+#define R9A06G032_CLK_UART4 150
+#define R9A06G032_CLK_UART5 151
+#define R9A06G032_CLK_UART6 152
+#define R9A06G032_CLK_UART7 153
+
+#endif /* __DT_BINDINGS_R9A06G032_SYSCTRL_H__ */
--
2.25.1
