On 2023/4/19 00:46, Jonas Karlman wrote:
This rearrange and remove duplicate defines to make the code cleaner.

There is no need to read vendor area1 and use an offset each time, it is
easier and clearer to just use the reg offset defined in TRM, same as
the other vendor regs.

This also removes use of the misspelled const for the RK3588 CMDOUT reg,
it will be re-added when support for RK3588 is introduced.

Signed-off-by: Jonas Karlman <jo...@kwiboo.se>
Reviewed-by: Kever Yang <kever.y...@rock-chips.com>

Thanks,
- Kever

---
v2:
- No change

  drivers/mmc/rockchip_sdhci.c | 40 ++++++++++++------------------------
  1 file changed, 13 insertions(+), 27 deletions(-)

diff --git a/drivers/mmc/rockchip_sdhci.c b/drivers/mmc/rockchip_sdhci.c
index 9716fbb54dd4..bcf65e091741 100644
--- a/drivers/mmc/rockchip_sdhci.c
+++ b/drivers/mmc/rockchip_sdhci.c
@@ -47,46 +47,36 @@
  #define ARASAN_VENDOR_REGISTER                0x78
  #define ARASAN_VENDOR_ENHANCED_STROBE BIT(0)
-/* DWC IP vendor area 1 pointer */
-#define DWCMSHC_P_VENDOR_AREA1         0xe8
-#define DWCMSHC_AREA1_MASK             GENMASK(11, 0)
-/* Offset inside the vendor area 1 */
-#define DWCMSHC_EMMC_CONTROL           0x2c
+/* Rockchip specific Registers */
+#define DWCMSHC_EMMC_EMMC_CTRL         0x52c
  #define DWCMSHC_CARD_IS_EMMC          BIT(0)
  #define DWCMSHC_ENHANCED_STROBE               BIT(8)
-
-/* Rockchip specific Registers */
  #define DWCMSHC_EMMC_DLL_CTRL         0x800
  #define DWCMSHC_EMMC_DLL_CTRL_RESET   BIT(1)
  #define DWCMSHC_EMMC_DLL_RXCLK                0x804
  #define DWCMSHC_EMMC_DLL_TXCLK                0x808
  #define DWCMSHC_EMMC_DLL_STRBIN               0x80c
-#define DECMSHC_EMMC_DLL_CMDOUT                0x810
  #define DWCMSHC_EMMC_DLL_STATUS0      0x840
  #define DWCMSHC_EMMC_DLL_STATUS1      0x844
  #define DWCMSHC_EMMC_DLL_START                BIT(0)
-#define DWCMSHC_EMMC_DLL_RXCLK_SRCSEL  29
+#define DWCMSHC_EMMC_DLL_LOCKED                BIT(8)
+#define DWCMSHC_EMMC_DLL_TIMEOUT       BIT(9)
  #define DWCMSHC_EMMC_DLL_START_POINT  16
  #define DWCMSHC_EMMC_DLL_START_DEFAULT        5
  #define DWCMSHC_EMMC_DLL_INC_VALUE    2
  #define DWCMSHC_EMMC_DLL_INC          8
  #define DWCMSHC_EMMC_DLL_BYPASS               BIT(24)
  #define DWCMSHC_EMMC_DLL_DLYENA               BIT(27)
+#define DLL_RXCLK_NO_INVERTER          BIT(29)
+#define DLL_RXCLK_ORI_GATE             BIT(31)
  #define DLL_TXCLK_TAPNUM_DEFAULT      0xA
-
+#define DLL_TXCLK_TAPNUM_FROM_SW       BIT(24)
  #define DLL_STRBIN_TAPNUM_DEFAULT     0x8
  #define DLL_STRBIN_TAPNUM_FROM_SW     BIT(24)
  #define DLL_STRBIN_DELAY_NUM_SEL      BIT(26)
  #define DLL_STRBIN_DELAY_NUM_OFFSET   16
  #define DLL_STRBIN_DELAY_NUM_DEFAULT  0x16
-#define DLL_TXCLK_TAPNUM_FROM_SW BIT(24)
-#define DWCMSHC_EMMC_DLL_LOCKED                BIT(8)
-#define DWCMSHC_EMMC_DLL_TIMEOUT       BIT(9)
-#define DLL_RXCLK_NO_INVERTER          1
-#define DLL_RXCLK_INVERTER             0
-#define DLL_RXCLK_ORI_GATE             BIT(31)
-#define DWCMSHC_ENHANCED_STROBE                BIT(8)
  #define DLL_LOCK_WO_TMOUT(x) \
        ((((x) & DWCMSHC_EMMC_DLL_LOCKED) == DWCMSHC_EMMC_DLL_LOCKED) && \
        (((x) & DWCMSHC_EMMC_DLL_TIMEOUT) == 0))
@@ -328,8 +318,7 @@ static int rk3568_sdhci_config_dll(struct sdhci_host *host, 
u32 clock, bool enab
                if (ret)
                        return ret;
- extra = DWCMSHC_EMMC_DLL_DLYENA |
-                       DLL_RXCLK_NO_INVERTER << DWCMSHC_EMMC_DLL_RXCLK_SRCSEL;
+               extra = DWCMSHC_EMMC_DLL_DLYENA | DLL_RXCLK_NO_INVERTER;
                sdhci_writel(host, extra, DWCMSHC_EMMC_DLL_RXCLK);
extra = DWCMSHC_EMMC_DLL_DLYENA |
@@ -346,10 +335,9 @@ static int rk3568_sdhci_config_dll(struct sdhci_host 
*host, u32 clock, bool enab
                 * Disable DLL and reset both of sample and drive clock.
                 * The bypass bit and start bit need to be set if DLL is not 
locked.
                 */
-               sdhci_writel(host, DWCMSHC_EMMC_DLL_BYPASS | 
DWCMSHC_EMMC_DLL_START,
-                            DWCMSHC_EMMC_DLL_CTRL);
+               extra = DWCMSHC_EMMC_DLL_BYPASS | DWCMSHC_EMMC_DLL_START;
+               sdhci_writel(host, extra, DWCMSHC_EMMC_DLL_CTRL);
                sdhci_writel(host, DLL_RXCLK_ORI_GATE, DWCMSHC_EMMC_DLL_RXCLK);
-               sdhci_writel(host, 0, DECMSHC_EMMC_DLL_CMDOUT);
                sdhci_writel(host, 0, DWCMSHC_EMMC_DLL_TXCLK);
                /*
                 * Before switching to hs400es mode, the driver will enable
@@ -368,7 +356,7 @@ static int rk3568_sdhci_config_dll(struct sdhci_host *host, 
u32 clock, bool enab
  static int rk3568_sdhci_set_ios_post(struct sdhci_host *host)
  {
        struct mmc *mmc = host->mmc;
-       u32 reg, vendor_reg;
+       u32 reg;
reg = sdhci_readw(host, SDHCI_HOST_CONTROL2);
        reg &= ~SDHCI_CTRL_UHS_MASK;
@@ -400,9 +388,7 @@ static int rk3568_sdhci_set_ios_post(struct sdhci_host 
*host)
sdhci_writew(host, reg, SDHCI_HOST_CONTROL2); - vendor_reg = (sdhci_readl(host, DWCMSHC_P_VENDOR_AREA1) & DWCMSHC_AREA1_MASK)
-                    + DWCMSHC_EMMC_CONTROL;
-       reg = sdhci_readw(host, vendor_reg);
+       reg = sdhci_readw(host, DWCMSHC_EMMC_EMMC_CTRL);
if (IS_MMC(mmc))
                reg |= DWCMSHC_CARD_IS_EMMC;
@@ -414,7 +400,7 @@ static int rk3568_sdhci_set_ios_post(struct sdhci_host 
*host)
        else
                reg &= ~DWCMSHC_ENHANCED_STROBE;
- sdhci_writew(host, reg, vendor_reg);
+       sdhci_writew(host, reg, DWCMSHC_EMMC_EMMC_CTRL);
return 0;
  }

Reply via email to