On 2023/6/5 3:23, Jan Kiszka wrote:
> On 25.05.23 11:36, Yanhong Wang wrote:
>> Enabled ID_EEPROM and I2C configuration for StarFive VisionFive2 board.
>>
>> Signed-off-by: Yanhong Wang <yanhong.w...@starfivetech.com>
>> ---
>> configs/starfive_visionfive2_defconfig | 19 ++++++++++++++++++-
>> 1 file changed, 18 insertions(+), 1 deletion(-)
>>
>> diff --git a/configs/starfive_visionfive2_defconfig
>> b/configs/starfive_visionfive2_defconfig
>> index c57708199d..570a1f53a1 100644
>> --- a/configs/starfive_visionfive2_defconfig
>> +++ b/configs/starfive_visionfive2_defconfig
>> @@ -13,6 +13,7 @@ CONFIG_SYS_PROMPT="StarFive #"
>> CONFIG_OF_LIBFDT_OVERLAY=y
>> CONFIG_DM_RESET=y
>> CONFIG_SPL_MMC=y
>> +CONFIG_SPL_DRIVERS_MISC=y
>> CONFIG_SPL_STACK=0x8180000
>> CONFIG_SPL=y
>> CONFIG_SPL_SPI_FLASH_SUPPORT=y
>> @@ -23,6 +24,7 @@ CONFIG_SPL_OPENSBI_LOAD_ADDR=0x40000000
>> CONFIG_ARCH_RV64I=y
>> CONFIG_CMODEL_MEDANY=y
>> CONFIG_RISCV_SMODE=y
>> +# CONFIG_OF_BOARD_FIXUP is not set
>> CONFIG_FIT=y
>> CONFIG_DISTRO_DEFAULTS=y
>> CONFIG_QSPI_BOOT=y
>> @@ -34,6 +36,8 @@ CONFIG_PREBOOT="setenv fdt_addr ${fdtcontroladdr};fdt addr
>> ${fdtcontroladdr};"
>> CONFIG_DEFAULT_FDT_FILE="starfive/jh7110-starfive-visionfive-2.dtb"
>> CONFIG_DISPLAY_CPUINFO=y
>> CONFIG_DISPLAY_BOARDINFO=y
>> +CONFIG_ID_EEPROM=y
>> +CONFIG_SYS_EEPROM_BUS_NUM=5
>> CONFIG_SPL_MAX_SIZE=0x40000
>> CONFIG_SPL_PAD_TO=0x0
>> CONFIG_SPL_BSS_START_ADDR=0x8040000
>> @@ -45,21 +49,34 @@ CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x80000000
>> CONFIG_SYS_SPL_MALLOC_SIZE=0x400000
>> CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
>> CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=0x2
>> +CONFIG_SPL_I2C=y
>> CONFIG_SPL_DM_SPI_FLASH=y
>> CONFIG_SPL_DM_RESET=y
>> CONFIG_SPL_SPI_LOAD=y
>> CONFIG_SYS_CBSIZE=256
>> CONFIG_SYS_PBSIZE=276
>> CONFIG_SYS_BOOTM_LEN=0x4000000
>> +CONFIG_CMD_EEPROM=y
>> +CONFIG_SYS_EEPROM_SIZE=512
>> +CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=4
>> +CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
>> CONFIG_CMD_MEMINFO=y
>> +CONFIG_CMD_I2C=y
>> CONFIG_CMD_TFTPPUT=y
>> +CONFIG_OF_BOARD=y
>> CONFIG_SYS_RELOC_GD_ENV_ADDR=y
>> +CONFIG_SPL_DM_SEQ_ALIAS=y
>> CONFIG_REGMAP=y
>> CONFIG_SYSCON=y
>> CONFIG_SPL_CLK_COMPOSITE_CCF=y
>> CONFIG_CLK_COMPOSITE_CCF=y
>> CONFIG_SPL_CLK_JH7110=y
>> -# CONFIG_I2C is not set
>> +CONFIG_DM_I2C=y
>> +CONFIG_SYS_I2C_DW=y
>> +CONFIG_MISC=y
>> +CONFIG_I2C_EEPROM=y
>> +CONFIG_SPL_I2C_EEPROM=y
>> +CONFIG_SYS_I2C_EEPROM_ADDR=0X50
>> CONFIG_MMC_HS400_SUPPORT=y
>> CONFIG_SPL_MMC_HS400_SUPPORT=y
>> CONFIG_MMC_DW=y
>
> This comes too late: Already patch 4 needs at least CONFIG_ID_EEPROM=y,
> if not more.
>
Moving patch 4 to the series end, is that okay?
> Make sure you don't leave non-bisectable commit series behind. Whenever
> something breaks (like 55171aedda88), people will use bisection to find
> the causing commit, and then they will appreciate not having to deal
> with such hick-ups.
>
> Jan
>
