On Tue, Jul 25, 2023 at 05:03:28PM -0500, Nishanth Menon wrote: > On 17:42-20230725, Tom Rini wrote: > > On Tue, Jul 25, 2023 at 04:37:55PM -0500, Nishanth Menon wrote: > > > On 17:25-20230725, Tom Rini wrote: > > > > On Tue, Jul 25, 2023 at 01:52:50PM -0500, Nishanth Menon wrote: > > > [..] > > > > > > > > + /* Set USB0 PHY core voltage to 0.85V */ > > > > > + val = readl(CTRLMMR_USB0_PHY_CTRL); > > > > > + val &= ~(CORE_VOLTAGE); > > > > > + writel(val, CTRLMMR_USB0_PHY_CTRL); > > > > > + > > > > > + /* Set USB1 PHY core voltage to 0.85V */ > > > > > + val = readl(CTRLMMR_USB1_PHY_CTRL); > > > > > + val &= ~(CORE_VOLTAGE); > > > > > + writel(val, CTRLMMR_USB1_PHY_CTRL); > > > > > + > > > > > + /* We have 32k crystal, so lets enable it */ > > > > > + val = readl(MCU_CTRL_LFXOSC_CTRL); > > > > > + val &= ~(MCU_CTRL_LFXOSC_32K_DISABLE_VAL); > > > > > + writel(val, MCU_CTRL_LFXOSC_CTRL); > > > > > + /* Add any TRIM needed for the crystal here.. */ > > > > > + /* Make sure to mux up to take the SoC 32k from the crystal */ > > > > > + writel(MCU_CTRL_DEVICE_CLKOUT_LFOSC_SELECT_VAL, > > > > > + MCU_CTRL_DEVICE_CLKOUT_32K_CTRL); > > > > > + > > > > > + /* Setup debounce conf registers - arbitrary values. Times are > > > > > approx */ > > > > > + /* 1.9ms debounce @ 32k */ > > > > > + writel(WKUP_CTRLMMR_DBOUNCE_CFG1, 0x1); > > > > > + /* 5ms debounce @ 32k */ > > > > > + writel(WKUP_CTRLMMR_DBOUNCE_CFG2, 0x5); > > > > > + /* 20ms debounce @ 32k */ > > > > > + writel(WKUP_CTRLMMR_DBOUNCE_CFG3, 0x14); > > > > > + /* 46ms debounce @ 32k */ > > > > > + writel(WKUP_CTRLMMR_DBOUNCE_CFG4, 0x18); > > > > > + /* 100ms debounce @ 32k */ > > > > > + writel(WKUP_CTRLMMR_DBOUNCE_CFG5, 0x1c); > > > > > + /* 156ms debounce @ 32k */ > > > > > + writel(WKUP_CTRLMMR_DBOUNCE_CFG6, 0x1f); > > > > > + > > > > > video_setup(); > > > > > enable_caches(); > > > > > if (IS_ENABLED(CONFIG_SPL_SPLASH_SCREEN) && > > > > > IS_ENABLED(CONFIG_SPL_BMP)) > > > > > > > > Here's a whole lot of seemingly board specific code in a function and > > > > file that's supposed to support any am62 platform. Is this really what > > > > we need, where we need it? > > > > > > * without using the correct voltage for USB, we risk damaging the IOs - > > > board specific, sure. > > > > So what happens when we do this on the other EVM, does it have the same > > values? Is there some must-always-be-safe values? Or is the answer "we > > must do this board specific to be safe" and so need to re-think what can > > and can't be shared between board builds. > > At least the ones we have currently (I am not sure about toradex, > phytech etc), seem to operate the vdd_core at 0.85V .. (which is what > USB is dependent upon).
For Toradex, we do have the equivalent code in our board file, see https://git.toradex.com/cgit/u-boot-toradex.git/tree/board/toradex/verdin-am62/verdin-am62.c?h=toradex_ti-u-boot-2023.04#n92 The 32kHz configuration is just different for us, we do not re-use the same you have here. The debounce conf registers I have no idea what they are about, something we should have also on our board? Any additional details? Francesco
