Hi Alexander, On 8/9/23 17:16, Alexander Dahl wrote:
The board has two SD card slots and we have two defconfigs for booting from either the first (micro SD) named 'sam9x60_curiosity_mmc_defconfig' or the second (full size SD) named 'sam9x60_curiosity_mmc1_defconfig'. For comparable Microchip boards (sama5d27-som1-ek, sama5d29-curiosity, sama7g5ek) with two card slots the defconfigs only differ in BOOTARGS, BOOTCOMMAND, and ENV_FAT_DEVICE_AND_PART and the same should be the case for sam9x60_curiosity.
To shed some light on this: the defconfigs for different at91 boards should differ only in terms of *where the env is stored*, but all the drivers should be available in all defconfigs. The `where it boots from` sometimes is not related to the name of the defconfig, because e.g. we have board_qspiflash_defconfigs, which store the env in the qspi flash, but do not boot Linux from it, main reason is that the QSPI flash is very small (8 Mbytes e.g.) Most boards have a simple boot example from the same media as where the env is stored, but it's not always the case as seen above.
Here the 'mmc1' config has more options enabled to support the raw NAND flash populated on the board, so the 'mmc' config (for mmc0) was adapted by enabling additional options, instead of removing options from mmc1. Signed-off-by: Alexander Dahl <a...@thorsis.com> --- configs/sam9x60_curiosity_mmc_defconfig | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) diff --git a/configs/sam9x60_curiosity_mmc_defconfig b/configs/sam9x60_curiosity_mmc_defconfig index 10937d67d7..269f015989 100644 --- a/configs/sam9x60_curiosity_mmc_defconfig +++ b/configs/sam9x60_curiosity_mmc_defconfig @@ -23,7 +23,7 @@ CONFIG_FIT=y CONFIG_SD_BOOT=y CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="mem=128M console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait" +CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait"
Have you checked the Linux DT if the memory is 128M hence the `mem=128M` is redundant ?
CONFIG_USE_BOOTCOMMAND=y CONFIG_BOOTCOMMAND="fatload mmc 0:1 0x21000000 at91-sam9x60_curiosity.dtb; fatload mmc 0:1 0x22000000 zImage; bootz 0x22000000 - 0x21000000" CONFIG_SYS_CONSOLE_IS_IN_ENV=y @@ -38,6 +38,8 @@ CONFIG_CMD_DM=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_NAND=y +CONFIG_CMD_NAND_TRIMFFS=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_BOOTP_BOOTFILESIZE=y @@ -50,6 +52,8 @@ CONFIG_OF_CONTROL=y CONFIG_ENV_IS_IN_FAT=y CONFIG_ENV_FAT_DEVICE_AND_PART="0:1" CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_REGMAP=y +CONFIG_SYSCON=y CONFIG_CLK=y CONFIG_CLK_CCF=y CONFIG_CLK_AT91=y @@ -60,10 +64,17 @@ CONFIG_CPU=y CONFIG_AT91_GPIO=y CONFIG_DM_I2C=y CONFIG_SYS_I2C_AT91=y +CONFIG_ATMEL_EBI=y +CONFIG_MFD_ATMEL_SMC=y CONFIG_I2C_EEPROM=y CONFIG_MICROCHIP_FLEXCOM=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ATMEL=y +CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_MTD_RAW_NAND=y +CONFIG_DM_NAND_ATMEL=y +CONFIG_SYS_NAND_ONFI_DETECTION=y CONFIG_PHY_MICREL=y CONFIG_MACB=y CONFIG_PINCTRL=y @@ -71,6 +82,8 @@ CONFIG_PINCTRL_AT91=y CONFIG_DM_SERIAL=y CONFIG_DEBUG_UART_ANNOUNCE=y CONFIG_ATMEL_USART=y +CONFIG_SYSRESET=y +CONFIG_SYSRESET_AT91=y CONFIG_TIMER=y CONFIG_MCHP_PIT64B_TIMER=y CONFIG_W1=y
