From: York Sun <york...@freescale.com> Tested all possible values for clk_adjust and write_data_delay for dual rank UDIMM and RDIMM to revise the tables.
Signed-off-by: York Sun <york...@freescale.com> Signed-off-by: Kumar Gala <ga...@kernel.crashing.org> --- board/freescale/mpc8572ds/ddr.c | 110 +++++++++++++++++++++++++++----------- 1 files changed, 78 insertions(+), 32 deletions(-) diff --git a/board/freescale/mpc8572ds/ddr.c b/board/freescale/mpc8572ds/ddr.c index d66ede2..cdde6ec 100644 --- a/board/freescale/mpc8572ds/ddr.c +++ b/board/freescale/mpc8572ds/ddr.c @@ -49,28 +49,27 @@ typedef struct { u32 force_2T; } board_specific_parameters_t; -/* ranges for parameters: - * wr_data_delay = 0-6 - * clk adjust = 0-8 - * cpo 2-0x1E (30) +/* + * CPO value doesn't matter if workaround for errata 111 and 134 enabled. + * + * For DDR2 DIMM, all combinations of clk_adjust and write_data_delay have been + * tested. For RDIMM, clk_adjust = 4 and write_data_delay = 3 is optimized for + * all clocks from 400MT/s to 800MT/s, verified with Kingston KVR800D2D8P6/2G. + * For UDIMM, clk_adjust = 8 and write_delay = 5 is optimized for all clocks + * from 400MT/s to 800MT/s, verified with Micron MT18HTF25672AY-800E1. */ - - -/* XXX: these values need to be checked for all interleaving modes. */ -/* XXX: No reliable dual-rank 800 MHz setting has been found. It may - * seem reliable, but errors will appear when memory intensive - * program is run. */ -/* XXX: Single rank at 800 MHz is OK. */ -const board_specific_parameters_t board_specific_parameters[][20] = { +const board_specific_parameters_t board_specific_parameters_udimm[][20] = { { - /* memory controller 0 */ - /* lo| hi| num| clk| cpo|wrdata|2T */ - /* mhz| mhz|ranks|adjst| | delay| */ - { 0, 333, 2, 6, 7, 3, 0}, - {334, 400, 2, 6, 9, 3, 0}, - {401, 549, 2, 6, 11, 3, 0}, - {550, 680, 2, 1, 10, 5, 0}, - {681, 850, 2, 1, 12, 5, 1}, + /* + * memory controller 0 + * lo| hi| num| clk| cpo|wrdata|2T + * mhz| mhz|ranks|adjst| | delay| + */ + { 0, 333, 2, 8, 7, 5, 0}, + {334, 400, 2, 8, 9, 5, 0}, + {401, 549, 2, 8, 11, 5, 0}, + {550, 680, 2, 8, 10, 5, 0}, + {681, 850, 2, 8, 12, 5, 1}, { 0, 333, 1, 6, 7, 3, 0}, {334, 400, 1, 6, 9, 3, 0}, {401, 549, 1, 6, 11, 3, 0}, @@ -79,14 +78,16 @@ const board_specific_parameters_t board_specific_parameters[][20] = { }, { - /* memory controller 1 */ - /* lo| hi| num| clk| cpo|wrdata|2T */ - /* mhz| mhz|ranks|adjst| | delay| */ - { 0, 333, 2, 6, 7, 3, 0}, - {334, 400, 2, 6, 9, 3, 0}, - {401, 549, 2, 6, 11, 3, 0}, - {550, 680, 2, 1, 11, 6, 0}, - {681, 850, 2, 1, 13, 6, 1}, + /* + * memory controller 1 + * lo| hi| num| clk| cpo|wrdata|2T + * mhz| mhz|ranks|adjst| | delay| + */ + { 0, 333, 2, 8, 7, 5, 0}, + {334, 400, 2, 8, 9, 5, 0}, + {401, 549, 2, 8, 11, 5, 0}, + {550, 680, 2, 8, 11, 5, 0}, + {681, 850, 2, 8, 13, 5, 1}, { 0, 333, 1, 6, 7, 3, 0}, {334, 400, 1, 6, 9, 3, 0}, {401, 549, 1, 6, 11, 3, 0}, @@ -95,16 +96,56 @@ const board_specific_parameters_t board_specific_parameters[][20] = { } }; +const board_specific_parameters_t board_specific_parameters_rdimm[][20] = { + { + /* + * memory controller 0 + * lo| hi| num| clk| cpo|wrdata|2T + * mhz| mhz|ranks|adjst| | delay| + */ + { 0, 333, 2, 4, 7, 3, 0}, + {334, 400, 2, 4, 9, 3, 0}, + {401, 549, 2, 4, 11, 3, 0}, + {550, 680, 2, 4, 10, 3, 0}, + {681, 850, 2, 4, 12, 3, 1}, + }, + + { + /* + * memory controller 1 + * lo| hi| num| clk| cpo|wrdata|2T + * mhz| mhz|ranks|adjst| | delay| + */ + { 0, 333, 2, 4, 7, 3, 0}, + {334, 400, 2, 4, 9, 3, 0}, + {401, 549, 2, 4, 11, 3, 0}, + {550, 680, 2, 4, 11, 3, 0}, + {681, 850, 2, 4, 13, 3, 1}, + } +}; + void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm, unsigned int ctrl_num) { - const board_specific_parameters_t *pbsp = - &(board_specific_parameters[ctrl_num][0]); - u32 num_params = sizeof(board_specific_parameters[ctrl_num]) / - sizeof(board_specific_parameters[0][0]); + const board_specific_parameters_t *pbsp; + u32 num_params; u32 i; ulong ddr_freq; + int matched = 0; + + if (!pdimm->n_ranks) + return; + + if (popts->registered_dimm_en) { + pbsp = &(board_specific_parameters_rdimm[ctrl_num][0]); + num_params = sizeof(board_specific_parameters_rdimm[ctrl_num]) / + sizeof(board_specific_parameters_rdimm[0][0]); + } else { + pbsp = &(board_specific_parameters_udimm[ctrl_num][0]); + num_params = sizeof(board_specific_parameters_udimm[ctrl_num]) / + sizeof(board_specific_parameters_udimm[0][0]); + } /* set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If @@ -138,10 +179,15 @@ void fsl_ddr_board_options(memctl_options_t *popts, popts->cpo_override = pbsp->cpo; popts->write_data_delay = pbsp->write_data_delay; popts->twoT_en = pbsp->force_2T; + matched = 1; + break; } pbsp++; } + if (!matched) + printf("Warning: board specific timing not found!\n"); + /* * Factors to consider for half-strength driver enable: * - number of DIMMs installed -- 1.7.2.3 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot