Historically, Qualcomm boards in U-Boot have all had their own
board/qualcomm/xyz directory, their own CONFIG_TARGET_XYZ option, their
own hardcoded sysmap-xyz.c file, and their own U-Boot specific
devicetree with little/no compatibility with upstream DT.
This series makes a few final prepatory changes, and then replaces
almost all of the board specific code with generic alternatives. The end
result is that all Qualcomm boards both current and future (with the
exception of the db410c and db820c) can be supported by a single U-Boot
binary by just providing the correct DT. New boards can be added without
introducing any addition mach/ or board/ code or config options.
Due to the nature of this change, the patch ("mach-snapdragon:
generalise board support") has become pretty big, I tried a few
different ways to represent this in git history, but the other methods
(e.g. adding a stub "generic" target and removing it again) were more
confusing and made for much messier git history. The current patch is
mostly atomic, but requires regenerating the config.
The QCS404 EVB board had some code to enable the USB VBUS regulator,
this is dropped in favour of a adding a new vbus-supply property to the
dwc3-generic driver. This will also be used by the dragonboard845c in a
future patch. This handles the common case of a board requiring some
regulator be enabled for USB host mode.
A more detailed description of the changes is below.
== Memory map ==
The memory map was historically hardcoded into U-Boot, this meant that
U-Boot had to be built for a specific variant of a device. This is
changed to instead read the memory map from the DT /memory node.
Additionally, most boards mapped addresss 0x0 as valid, as a result if a
null pointer access happens then it will cause a bus stall (and board
hang). This is fixed so that null pointer accesses will now correctly
throw an exception.
== DT loading ==
Previously, boards used the FDT blob embedded into U-Boot (via
OF_SEPARATE). However, most Qualcomm boards run U-Boot as a secondary
bootloader, so we can instead rely on the first-stage bootloader to
populate some useful FDT properties for us (notably the /memory node and
KASLR seed) and fetch the DTB that it provides. Combined with the memory
map changes above, this let's us entirely avoid configuring the memory
map explicitly.
== defconfig ==
Most of the board defconfigs and config headers were quite similar, to
simplify maintenance going forward, all the fully generic boards (sdm845
and qcs404-evb so far) are adapted to use the new qcom_defconfig. Going
forward, all new Qualcomm boards should be supported by this defconfig.
A notable exception is for specific usecases (like U-Boot as the primary
bootloader).
== The older dragonboards ==
The db410c and db820c both have some custom board init code, as a result
they aren't yet binary compatible. mach-snapdragon is adjusted so
that all the necessary config options (e.g. CONFIG_SYS_BOARD) can be set
from their defconfigs, this makes it possible to enable support for new
boards without introducing additional config options.
The db410c can run U-Boot either chainloaded like the other boards, or
as a first-stage bootloader replacing aboot. However it was hardcoded to
only build for the latter option. This series introduces a new
"chainloaded" defconfig to enable easier testing via fastboot.
== dynamic environment variables ==
This series also introduces runtime-allocated load addresses via the lmb
allocator. This allows for booting on boards with vastly different
memory layouts without any pre-calculation or macro magic in the config
header. This feature is based on similar code in mach-apple.
The soc, board, and fdtfile environment variables are also generated
automatically. Many Qualcomm boards follow a similar scheme for DTB
naming such that the name can often be derived from the root compatible
properties. This is intended to cover the most common cases and be a
simple solution for booting generic distro images without having to
explicitly choose the right DTB. The U-Boot DTS can be tweaked if
necessary to produce the correct name, the variable can be overwritten,
or a bootloader like GRUB can load the devicetree instead.
== Upstream DT ==
All Qualcomm boards have had their devicetree files replaced with the
upstream versions. Previous patch series made the necessary driver
adjustments to fully support the upstream DT format. All future
Qualcomm boards should use upstream DTS by default.
Once Sumit's work to import dt-rebasing has been merged, we will drop
the imported DT and bindings again.
---
I have tested this series on the Dragonboard410c, Dragonboard820c, and
Dragonboard845c. I unfortunately don't have access to a QCS404 EVB board
to test.
This series is based on the qcom-next branch [1] and depends on my PMIC
fixes series [2], an integration branch for testing can be found at [3].
The non-qualcomm-specific changes (patches 1 and 2) don't have any
dependencies.
[1]: https://source.denx.de/u-boot/custodians/u-boot-snapdragon
[2]:
https://lore.kernel.org/u-boot/20231114-b4-qcom-dt-compat-v3-0-88a92f8f0...@linaro.org/
[3]:
https://source.denx.de/u-boot/custodians/u-boot-snapdragon/-/tree/b4/qcom-common-target
---
Changes in v3:
- Remove dragonboard410c.dts file
- Introduce generic board_usb_init() function.
- Remove db410c specific dead code (smem RAM layout)
- Fix pinctrl DT compatibility for msm8916/msm8996
- Reference git tag where DT and headers were taken from Linux.
- Adjust ramdisk allocation size to 128M
- Improve documentation wording, reference buildman
- Fix mapping for reserved regions to avoid speculative pre-fetching
- Apply quicksort to memory banks read from DT to ensure ordering
- Link to v2:
https://lore.kernel.org/r/20231219-b4-qcom-common-target-v2-0-b6dd97042...@linaro.org
Changes in v2:
- Split DTS changes to reduce patch size.
- Import full board DTS files from Linux too, and introduce -u-boot.dtsi
files where necessary to make any U-Boot specific changes.
- Add a pinctrl driver for qcom PMIC GPIOs
- Always enable LINUX_KERNEL_IMAGE_HEADER
- Link to v1:
https://lore.kernel.org/r/20231121-b4-qcom-common-target-v1-0-9492198e0...@linaro.org
To: Neil Armstrong <neil.armstr...@linaro.org>
To: Sumit Garg <sumit.g...@linaro.org>
To: Ramon Fried <rfried....@gmail.com>
Cc: Marek Vasut <ma...@denx.de>
To: Dzmitry Sankouski <dsankou...@gmail.com>
To: Caleb Connolly <caleb.conno...@linaro.org>
To: Peng Fan <peng....@nxp.com>
To: Jaehoon Chung <jh80.ch...@samsung.com>
To: Rayagonda Kokatanur <rayagonda.kokata...@broadcom.com>
To: Lukasz Majewski <lu...@denx.de>
To: Sean Anderson <sean...@gmail.com>
To: Jorge Ramirez-Ortiz <jorge.ramirez.or...@gmail.com>
To: Stephan Gerhold <step...@gerhold.net>
Cc: <u-boot@lists.denx.de>
---
Caleb Connolly (36):
arm: init: export prev_bl_fdt_addr
usb: dwc3-generic: support external vbus regulator
mmc: msm_sdhci: use modern clock handling
dt-bindings: drop msm_sdhci binding
clk/qcom: use upstream compatible properties
clock/qcom: qcs404: fix clk_set_rate
serial: msm: add debug UART
serial: msm: fix clock handling
serial_msm: fix pinctrl
gpio: qcom_pmic: 1-based GPIOs
gpio: qcom_pmic: add a quirk to skip GPIO configuration
gpio: qcom_pmic: add pinctrl driver
board: dragonboard410c: add chainloaded config fragment
board: dragonboard410c: upstream DT compat
board: dragonboard410c: import board code from mach-snapdragon
board: dragonboard820c: use LINUX_KERNEL_IMAGE_HEADER
mach-snapdragon: generalise board support
mach-snapdragon: dynamic load addresses
mach-snapdragon: generate fdtfile automatically
mach-snapdragon: carve out no-map regions
doc: board/qualcomm: document generic targets
dt-bindings: import headers for SDM845
dts: sdm845: import supporting dtsi files
dts: sdm845: replace with upstream DTS
dt-bindings: import headers for MSM8916
dts: msm8916: import PMIC dtsi files
dts: msm8916: replace with upstream DTS
dt-bindings: import headers for MSM8996
dts: msm8996: import PMIC dtsi files
dts: dragonboard820c: use correct bindings for clocks
dts: msm8996: replace with upstream DTS
dt-bindings: import headers for qcs404
dts: qcs404-evb: replace with upstream DT
board: qcs404-evb: drop board code
pinctrl: qcom: fix DT compatibility
MAINTAINERS: Qualcomm: add some missing paths
MAINTAINERS | 12 +-
abort | 20 +
arch/arm/Kconfig | 4 +
arch/arm/dts/Makefile | 9 +-
arch/arm/dts/apq8016-sbc-u-boot.dtsi | 11 +
arch/arm/dts/apq8016-sbc.dts | 729 +++
arch/arm/dts/apq8096-db820c-u-boot.dtsi | 14 +
arch/arm/dts/apq8096-db820c.dts | 1137 ++++
arch/arm/dts/dragonboard410c-uboot.dtsi | 44 -
arch/arm/dts/dragonboard410c.dts | 209 -
arch/arm/dts/dragonboard820c-uboot.dtsi | 32 -
arch/arm/dts/dragonboard820c.dts | 151 -
arch/arm/dts/dragonboard845c-uboot.dtsi | 26 -
arch/arm/dts/dragonboard845c.dts | 48 -
arch/arm/dts/msm8916-pm8916.dtsi | 157 +
arch/arm/dts/msm8916.dtsi | 2702 +++++++++
arch/arm/dts/msm8996.dtsi | 3884 +++++++++++++
arch/arm/dts/pm8916.dtsi | 178 +
arch/arm/dts/pm8994.dtsi | 152 +
arch/arm/dts/pm8998.dtsi | 130 +
arch/arm/dts/pmi8994.dtsi | 65 +
arch/arm/dts/pmi8998.dtsi | 98 +
arch/arm/dts/pms405.dtsi | 149 +
arch/arm/dts/qcs404-evb-4000-u-boot.dtsi | 26 +
arch/arm/dts/qcs404-evb-4000.dts | 96 +
arch/arm/dts/qcs404-evb-uboot.dtsi | 30 -
arch/arm/dts/qcs404-evb.dts | 390 --
arch/arm/dts/qcs404-evb.dtsi | 389 ++
arch/arm/dts/qcs404.dtsi | 1829 ++++++
arch/arm/dts/sdm845-db845c.dts | 1190 ++++
.../arm/dts/sdm845-samsung-starqltechn-u-boot.dtsi | 16 +
arch/arm/dts/sdm845-samsung-starqltechn.dts | 460 ++
arch/arm/dts/sdm845-wcd9340.dtsi | 86 +
arch/arm/dts/sdm845.dtsi | 5801 +++++++++++++++++++-
arch/arm/dts/starqltechn-uboot.dtsi | 27 -
arch/arm/dts/starqltechn.dts | 68 -
arch/arm/lib/save_prev_bl_data.c | 5 +
arch/arm/mach-snapdragon/Kconfig | 95 +-
arch/arm/mach-snapdragon/Makefile | 8 +-
arch/arm/mach-snapdragon/board.c | 454 ++
arch/arm/mach-snapdragon/dram.c | 99 -
arch/arm/mach-snapdragon/include/mach/dram.h | 12 -
arch/arm/mach-snapdragon/include/mach/misc.h | 13 -
arch/arm/mach-snapdragon/init_sdm845.c | 73 -
arch/arm/mach-snapdragon/misc.c | 55 -
arch/arm/mach-snapdragon/sysmap-apq8016.c | 31 -
arch/arm/mach-snapdragon/sysmap-apq8096.c | 31 -
arch/arm/mach-snapdragon/sysmap-qcs404.c | 43 -
arch/arm/mach-snapdragon/sysmap-sdm845.c | 31 -
board/qualcomm/dragonboard410c/Kconfig | 15 -
board/qualcomm/dragonboard410c/Makefile | 2 +-
.../dragonboard410c/configs/chainloaded.config | 7 +
board/qualcomm/dragonboard410c/dragonboard410c.c | 130 +-
board/qualcomm/dragonboard820c/Kconfig | 15 -
board/qualcomm/dragonboard820c/Makefile | 1 -
board/qualcomm/dragonboard820c/dragonboard820c.c | 39 +-
board/qualcomm/dragonboard820c/head.S | 33 -
board/qualcomm/dragonboard820c/u-boot.lds | 111 -
board/qualcomm/dragonboard845c/Kconfig | 12 -
board/qualcomm/qcs404-evb/Kconfig | 15 -
board/qualcomm/qcs404-evb/Makefile | 6 -
board/qualcomm/qcs404-evb/qcs404-evb.c | 62 -
configs/dragonboard410c_defconfig | 8 +-
configs/dragonboard820c_defconfig | 8 +-
configs/dragonboard845c_defconfig | 29 -
configs/qcom_defconfig | 73 +
configs/qcs404evb_defconfig | 55 -
configs/starqltechn_defconfig | 41 -
doc/board/qualcomm/board.rst | 125 +
doc/board/qualcomm/debugging.rst | 61 +
doc/board/qualcomm/index.rst | 4 +-
doc/board/qualcomm/qcs404.rst | 79 -
doc/board/qualcomm/sdm845.rst | 167 -
doc/device-tree-bindings/mmc/msm_sdhci.txt | 25 -
doc/device-tree-bindings/usb/ehci-msm.txt | 10 -
drivers/clk/qcom/clock-apq8016.c | 9 +-
drivers/clk/qcom/clock-apq8096.c | 7 +-
drivers/clk/qcom/clock-qcs404.c | 7 +-
drivers/gpio/qcom_pmic_gpio.c | 224 +-
drivers/mmc/msm_sdhci.c | 69 +-
drivers/phy/qcom/msm8916-usbh-phy.c | 4 +-
drivers/pinctrl/qcom/pinctrl-apq8016.c | 28 +-
drivers/pinctrl/qcom/pinctrl-apq8096.c | 16 +-
drivers/pinctrl/qcom/pinctrl-qcs404.c | 16 +-
drivers/serial/Kconfig | 8 +
drivers/serial/serial_msm.c | 57 +-
drivers/usb/dwc3/dwc3-generic.c | 12 +
drivers/usb/host/ehci-msm.c | 24 +-
include/configs/dragonboard845c.h | 20 -
include/configs/qcom.h | 21 +
include/configs/qcs404-evb.h | 20 -
include/configs/sdm845.h | 26 -
include/dt-bindings/arm/coresight-cti-dt.h | 37 +
include/dt-bindings/clock/qcom,camcc-sdm845.h | 116 +
include/dt-bindings/clock/qcom,dispcc-sdm845.h | 56 +
include/dt-bindings/clock/qcom,gcc-msm8916.h | 179 +
include/dt-bindings/clock/qcom,gcc-msm8996.h | 362 ++
include/dt-bindings/clock/qcom,gpucc-sdm845.h | 24 +
include/dt-bindings/clock/qcom,lpass-sdm845.h | 15 +
include/dt-bindings/clock/qcom,mmcc-msm8996.h | 295 +
include/dt-bindings/clock/qcom,rpmcc.h | 174 +
include/dt-bindings/clock/qcom,rpmh.h | 37 +
include/dt-bindings/clock/qcom,turingcc-qcs404.h | 15 +
include/dt-bindings/clock/qcom,videocc-sdm845.h | 35 +
include/dt-bindings/dma/qcom-gpi.h | 11 +
include/dt-bindings/firmware/qcom,scm.h | 39 +
include/dt-bindings/iio/qcom,spmi-vadc.h | 300 +
include/dt-bindings/interconnect/qcom,msm8916.h | 100 +
.../dt-bindings/interconnect/qcom,msm8996-cbf.h | 12 +
include/dt-bindings/interconnect/qcom,msm8996.h | 163 +
include/dt-bindings/interconnect/qcom,osm-l3.h | 15 +
include/dt-bindings/interconnect/qcom,sdm845.h | 150 +
include/dt-bindings/phy/phy-qcom-qmp.h | 20 +
include/dt-bindings/phy/phy-qcom-qusb2.h | 37 +
include/dt-bindings/pinctrl/qcom,pmic-gpio.h | 164 +
include/dt-bindings/pinctrl/qcom,pmic-mpp.h | 106 +
include/dt-bindings/power/qcom-rpmpd.h | 412 ++
.../dt-bindings/regulator/qcom,rpmh-regulator.h | 36 +
include/dt-bindings/reset/qcom,gcc-msm8916.h | 100 +
include/dt-bindings/reset/qcom,sdm845-aoss.h | 17 +
include/dt-bindings/reset/qcom,sdm845-pdc.h | 22 +
include/dt-bindings/soc/qcom,apr.h | 28 +
include/dt-bindings/soc/qcom,rpmh-rsc.h | 14 +
include/dt-bindings/sound/apq8016-lpass.h | 9 +
include/dt-bindings/sound/qcom,lpass.h | 46 +
include/dt-bindings/sound/qcom,q6afe.h | 9 +
include/dt-bindings/sound/qcom,q6asm.h | 26 +
include/dt-bindings/sound/qcom,q6dsp-lpass-ports.h | 234 +
include/dt-bindings/sound/qcom,wcd9335.h | 15 +
include/init.h | 11 +
130 files changed, 23881 insertions(+), 2580 deletions(-)
---
base-commit: 4c3dfa1b8babf9fc0575ce08eed99f950d3bab84
// Caleb (they/them)
